The driver stores the PCI resource addresses into 'unsigned long' variable
before calling ioremap_nocache() on them. This warrants kernel oops when the
registers are accessed on PPC 44x platforms which (being 32-bit) have PCI
memory space mapped beyond 4 GB.

The arch/ppc/ kernel has a fixup in ioremap() that creates an illusion that
the PCI memory resource is mapped below 4 GB, but arch/powerpc/ code got rid
of this trick, having instead CONFIG_RESOURCES_64BIT enabled.

[ Bump driver version and release date -DaveM ]
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PPP support in generic HDLC in Linux 2.6.25 is broken and will cause
a kernel panic when a device configured in PPP mode is activated.

It will be replaced by new PPP implementation after Linux 2.6.25 is
released.

This affects only PPP support in generic HDLC (mostly Hitachi SCA
and SCA-II based drivers, wanxl, and few others). Standalone syncppp
and async PPP support are not affected.
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch fixes two weaknesses in send/receive packet handling which may
lead to kernel panics during DLPAR memory add operations.
Signed-off-by: NThomas Klein <tklein@de.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add missing sysfs device association. Compile tested only -ENOHW.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=10380Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Cc: Cesar Eduardo Barros <cesarb@cesarb.net>
Cc: <tom@sharkbay.at>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3956Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This critical patch fixes a mac address issue recently introduced.  If the
device's mac address was in correct order and the flag
NVREG_TRANSMITPOLL_MAC_ADDR_REV was set, during nv_remove the flag would get
cleared.  During next load, the mac address would get reversed because the
flag is missing.

As it has been indicated previously, the flag is cleared across a low power
transition.  Therefore, the driver should set the mac address back into the
reversed order when clearing the flag.

Also, the driver should set back the flag after a low power transition to
protect against kexec command calling nv_probe a second time.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Cc: "Yinghai Lu" <yhlu.kernel@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

It seems no good reason to use comma here.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Call phy_disconnect() on remove routine.  Otherwise the phy timer
causes a kernel crash when unloading.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The new Fixed PHY method, fixed-link property, isn't
impl. for ucc_geth which makes fixed PHYs non functional.
Add support for the new method to restore the Fixed PHY
functionality.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

fs_enet_close() calls napi_disable() unconditionally. This patch skips the
call when use_napi isn't set.
Signed-off-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Any usage of sky2 on new Yukon Supreme would cause a NULL dereference.
The chip is very new, so the support is still untested; vendor has
not sent any eval hardware.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Copy the network namespace from the socket to the timewait socket.
Signed-off-by: NDaniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes kernel bugzilla 10371.

As reported by M.Piechaczek@osmosys.tv, if we try to grab a
char sized socket option value, as in:

  unsigned char ttl = 255;
  socklen_t     len = sizeof(ttl);
  setsockopt(socket, IPPROTO_IP, IP_MULTICAST_TTL, &ttl, &len);

  getsockopt(socket, IPPROTO_IP, IP_MULTICAST_TTL, &ttl, &len);

The ttl returned will be wrong on big-endian, and on both little-
endian and big-endian the next three bytes in userspace are written
with garbage.

It's because of this test in do_ip_getsockopt():

	if (len < sizeof(int) && len > 0 && val>=0 && val<255) {

It should allow a 'val' of 255 to pass here, but it doesn't so it
copies a full 'int' back to userspace.

On little-endian that will write the correct value into the location
but it spams on the next three bytes in userspace.  On big endian it
writes the wrong value into the location and spams the next three
bytes.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed bug: Wrong register was written to when bringing the chip out of
reset.

[ Bump driver version and release date -DaveM ]
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this patch, the generic L3 tracker would kick in
if nf_conntrack_ipv4 was not loaded before nf_nat, which
would lead to translation problems with ICMP errors.

NAT does not make sense without IPv4 connection tracking
anyway, so just add a call to need_ipv4_conntrack().
Signed-off-by: NJan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shifts larger than the data type are undefined, don't try to shift
an u32 by 32. Also remove some special-casing of bitmasks divisible
by 32.

Based on patch by Jan Engelhardt <jengelh@computergmbh.de>.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit df9dcb45 ([IPSEC]: Fix inter address family IPsec tunnel handling)
broke openswan by removing the selector initialization for tunnel mode
in case it is uninitialized.

This patch restores the initialization, fixing openswan, but probably
breaking inter-family tunnels again (unknown since the patch author
disappeared). The correct thing for inter-family tunnels is probably
to simply initialize the selector family explicitly.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The layer above will free the skb in an error case.
Signed-off-by: NDaniel Wagner <wagi@monom.org>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes assignment of the interrupt vectors on the SSB MIPS core.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes the TPS flag handling for the SSB pcicore driver.
This fixes interrupts on some devices.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When associating to a b-only AP where there is no ERP IE, short preamble
mode is left at previous state (probably also protection mode). In this
case, disable protection and use short preamble mode as specified in
capability field. The same is done if capability field is changed on-the-fly.
Signed-off-by: NVladimir Koutny <vlado@ksp.sk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If print_mac() is used inside of a pr_debug() the compiler
can't see that the call is redundant so still performs it
even of pr_debug() ends up being a nop.

So don't use print_mac() in such cases in hot code paths,
use MAC_FMT et al. instead.

As noted by Joe Perches, pr_debug() could be modified to
handle this better, but that is a change to an interface
used by the entire kernel and thus needs to be validated
carefully.  This here is thus the less risky fix for
2.6.25
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MTU probe can cause some remedies for FRTO because the normal
packet ordering may be violated allowing FRTO to make a wrong
decision (it might not be that serious threat for anything
though). Thus it's safer to not run FRTO while MTU probe is
underway.

It seems that the basic FRTO variant should also look for an
skb at probe_seq.start to check if that's retransmitted one
but I didn't implement it now (plain seqno in window check
isn't robust against wraparounds).
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes Bugzilla #10384

tcp_simple_retransmit does L increment without any checking
whatsoever for overflowing S+L when Reno is in use.

The simplest scenario I can currently think of is rather
complex in practice (there might be some more straightforward
cases though). Ie., if mss is reduced during mtu probing, it
may end up marking everything lost and if some duplicate ACKs
arrived prior to that sacked_out will be non-zero as well,
leading to S+L > packets_out, tcp_clean_rtx_queue on the next
cumulative ACK or tcp_fastretrans_alert on the next duplicate
ACK will fix the S counter.

More straightforward (but questionable) solution would be to
just call tcp_reset_reno_sack() in tcp_simple_retransmit but
it would negatively impact the probe's retransmission, ie.,
the retransmissions would not occur if some duplicate ACKs
had arrived.

So I had to add reno sacked_out reseting to CA_Loss state
when the first cumulative ACK arrives (this stale sacked_out
might actually be the explanation for the reports of left_out
overflows in kernel prior to 2.6.23 and S+L overflow reports
of 2.6.24). However, this alone won't be enough to fix kernel
before 2.6.24 because it is building on top of the commit
1b6d427b ([TCP]: Reduce sacked_out with reno when purging
write_queue) to keep the sacked_out from overflowing.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: NAlessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes a long-standing bug which makes NewReno recovery crippled.
With GSO the whole head skb was marked as LOST which is in
violation of NewReno procedure that only wants to mark one packet
and ended up breaking our TCP code by causing counter overflow
because our code was built on top of assumption about valid
NewReno procedure. This manifested as triggering a WARN_ON for
the overflow in a number of places.

It seems relatively safe alternative to just do nothing if
tcp_fragment fails due to oom because another duplicate ACK is
likely to be received soon and the fragmentation will be retried.

Special thanks goes to Soeren Sonnenburg <kernel@nn7.de> who was
lucky enough to be able to reproduce this so that the warning
for the overflow was hit. It's not as easy task as it seems even
if this bug happens quite often because the amount of outstanding
data is pretty significant for the mismarkings to lead to an
overflow.

Because it's very late in 2.6.25-rc cycle (if this even makes in
time), I didn't want to touch anything with SACK enabled here.
Fragmenting might be useful for it as well but it's more or less
a policy decision rather than mandatory fix. Thus there's no need
to rush and we can postpone considering tcp_fragment with SACK
for 2.6.26.

In 2.6.24 and earlier, this very same bug existed but the effect
is slightly different because of a small changes in the if
conditions that fit to the patch's context. With them nothing
got lost marker and thus no retransmissions happened.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fast retransmission can be forced locally to the rfc3517
branch in tcp_update_scoreboard instead of making such fragile
constructs deeper in tcp_mark_head_lost.

This is necessary for the next patch which must not have
loopholes for cnt > packets check. As one can notice,
readability got some improvements too because of this :-).
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the STA AID setting and actually makes hostapd/mac80211
work properly in presence of power-saving stations.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes an hard crash which happened upon driver loading on bcm4303 rev.
2 devices.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch enables the IWL4965_HT flag (n-band) in Kconfig.
Removed the "depends on n" from Kconfig for config IWL4965_HT
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit bada339b enforces that all
interfaces have a valid MAC address before they are brought up.

ipw2200 does not assign a MAC address to it's radiotap interface, meaning
that the radiotap interface cannot be brought up in 2.6.24.
https://bugs.gentoo.org/show_bug.cgi?id=215714

Fix this by copying the MAC address from the real interface.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After moving lbs_find_best_network_ssid() from scan.c to assoc.c gcc was
able to deduce that new_mode might stay uninitialized.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

a) if you initialize something with le32_to_cpu(...), then |= it
with host-endian and feed to cpu_to_le32(), it's most definitely
*not* __le32.  As sparse would've told you...

b) the whole sequence is |= cpu_to_le32(host-endian constant)
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

My previous section fix only turned one section problem into another
section problem.

This patch fixes it for real.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The other if blocks don't redeclare temp, remove the redeclaration in
the final if() block.

drivers/net/phy/marvell.c:214:7: warning: symbol 'temp' shadows an earlier one
drivers/net/phy/marvell.c:160:6: originally declared here
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

These entries are allocated in vlan_dev_set_egress_priority, 
but are never released and leaks on vlan device removal.

Drop these in vlan's ->uninit callback - after the device is 
brought down and everyone is notified about it is going to
be unregistered.

Found during testing vlan netnsization patchset.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5784 B step and newer chips require the PHY DSPs to be fine-tuned
based on one-time programmable values stored in the chip.  This is
essential to achieve optimal PHY operations especially when using
long cables.  We also need to properly handle the 10Mbit RX bit in the
CPMU_CTRL register during PHY reset.

Update version to 3.89.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Let it update the state of all CPUs. The network stack goes
into pains to feed the current IP addresses in, but it is not very
effective if that is only done for some random CPU instead of all.
So change it to feed bits into all CPUs.  I decided to do that lockless 
because well somewhat random results are ok.

v2: Drop rename so that this patch doesn't depend on x86 maintainers
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Anycast DST entries allocated inside ipv6_dev_ac_inc are leaked when
network device is stopped without removing IPv6 addresses from it. The
bug has been observed in the reality on 2.6.18-rhel5 kernel.

In the above case addrconf_ifdown marks all entries as obsolete and
ip6_del_rt called from __ipv6_dev_ac_dec returns ENOENT. The
referrence is not dropped.

The fix is simple. DST entry should not keep referrence when stored in
the FIB6 tree.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>