Impact: reduce kernel size a bit, address sparse warning

Addresses the problem pointed out by this sparse warning:
  arch/x86/kernel/apic/x2apic_cluster.c:13:1: warning: symbol 'per_cpu__x86_cpu_to_logical_apicid' was not declared. Should it be static?
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1239434726.4418.24.camel@localhost.localdomain>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: cleanup

this warning:

  arch/x86/kernel/early-quirks.c:99: warning: ‘ati_ixp4x0_rev’ defined but not used

triggers because ati_ixp4x0_rev() is only used in the
ACPI && X86_IO_APIC case.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Both software emulated and hardware based CTS and RTS are enabled in
serial driver.

The CTS RTS PIN connection on BF548 UART port is defined as a modem
device not as a host device.  In order to test it under Linux, please
nake a cross UART cable to exchange CTS and RTS signal.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Only the CTS bit is affected.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the new general RS485 Linux data structure (introduced by Alan with
commit number c26c56c0) in the Cris
architecture too (currently, Cris still uses the old private data
structure instead of the new one).
Signed-off-by: NClaudio Scordino <claudio@evidence.eu.com>
Tested-by: NHinko Kocevar <hinko.kocevar@cetrtapot.si>
Tested-by: NJanez Cufer <janez.cufer@cetrtapot.si>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace all DMA_24BIT_MASK macro with DMA_BIT_MASK(24)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Most SPI peripherals use GPIOs as their chip selects, introduce .gpio_cs
for this.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

1. Rewrite of the non-dma data transfer functions to use only ONE mode
   of TIMOD (TIMOD=0x1).  With TIMOD=0, it was not possible to set the TX
   bit pattern.  So the TDBR = 0xFFFF inside the read calls won't work.

2. Clear SPI_RDBR before reading and before duplex transfer.
   Otherwise the garbage data in RDBR will get read.  Since mmc_spi uses a
   lot of duplex transfers, this is the main cause of mmc_spi failure.

3. Poll RXS for transfer completion.  Polling SPIF or TXS cannot
   guarantee transfer completion.  This may interrupt a transfer before it
   is finished.  Also this may leave garbage data in buffer and affect
   next transfer.

[Yi Li <yi.li@analog.com>: add a field "u16 idle_tx_val" in "struct
bfin5xx_spi_chip" to specify the value to transmit if no TX value
is supplied.]
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: NYi Li <yi.li@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for GPIO controlled SPI Chip Selects.  To make use of this
feature, set chip_select = 0 and add a proper cs_gpio to your
controller_data.

struct spi_board_info
        .chip_select = 0

struct bfin5xx_spi_chip
        .cs_gpio = GPIO_P###

There are various SPI devices that require SPI MODE_0, and need to have
the Chip Selects asserted during the entire transfer.  Consider using
SPI_MODE_3 (SPI_CPHA | SPI_CPOL) if your device allows it.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix erroneous SPI Clock divisor calculation.  Make sure SPI_BAUD is always
>= 2.  Writing a value of 0 or 1 to the SPI_BAUD register disables the
serial clock.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove duplicated #include in arch/x86/kernel/ftrace.c.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
LKML-Reference: <1238503291-2532-1-git-send-email-weiyi.huang@gmail.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Preserve I2C clock settings for the Socrates MPC8544 board.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The platform data for the i2c-s3c2410 driver used to allow a min,
max and desired frequency for the I2C bus. This patch reduces it
to simply a desired frequency ceiling and corrects all the uses
of the platform data appropriately.

This means, for example, that on a system with a 66MHz fclk, a
request for 100KHz will achieve 65KHz which is safe and
acceptable, rather than 378KHz which it would have achieved
without this change.
Signed-off-by: NSimtec Linux Team <linux@simtec.co.uk>
Signed-off-by: NDaniel Silverstone <dsilvers@simtec.co.uk>
[ben-linux@fluff.org: tidy subject and description]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The sda_delay field should be specified in ns, not in clock ticks
as when using cpufreq we could be changing the bus rate.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>

Implementation of I2C Adapter/Algorithm Driver for I2C Bus integrated
in Freescale's i.MX/MXC processors.
Signed-off-by: NDarius Augulis <augulis.darius@gmail.com>
Tested-by: NSascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This fixes a problem reported by Sean MacLennan where loading any
module would cause an oops.  We weren't marking the pages containing
the module text as having hardware execute permission, due to a bug
introduced in commit 8d1cf34e ("powerpc/mm: Tweak PTE bit combination
definitions"), hence trying to execute the module text caused an
exception on processors that support hardware execute permission.

This adds _PAGE_HWEXEC to the definitions of PAGE_KERNEL_X and
PAGE_KERNEL_ROX to fix this problem.
Reported-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

[paulus@samba.org: changed to use syscall numbers 320 and 321 since
 perf_counters is currently using 319.]
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

'tramp' is an unsigned long, so print it with %lx.

Fixes the following build warning:
arch/powerpc/kernel/ftrace.c:291: error: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Commit bb725340 ("powerpc64,
ftrace: save toc only on modules for function graph"), added an
#if CONFIG_PPC64.  This changes it to #ifdef.

Fixes the following warning on 32-bit builds:
 arch/powerpc/kernel/ftrace.c:562:5: error: "CONFIG_PPC64" is not defined
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The ptrace compat wrapper mishandles access to the fpu registers.  The
PTRACE_PEEKUSR and PTRACE_POKEUSR requests miscalculate the index into
the fpr array due to the broken FPINDEX macro.  The
PPC_PTRACE_PEEKUSR_3264 request needs to use the same formula that the
native ptrace interface uses when operating on the register number (as
opposed to the 4-byte offset).  The PPC_PTRACE_POKEUSR_3264 request
didn't take TS_FPRWIDTH into account.
Signed-off-by: NAndreas Schwab <schwab@linux-m68k.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The irq remapping layer seems to cause some confusion when people
see a different irq number in /proc/interrupts vs the one they
request in their driver or DTS.

So have the irq remapping layer print out a message when we map an
irq. The message is only printed the first time the irq is mapped,
and it's KERN_DEBUG so most people won't see it.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

commit 28794d34 ("powerpc/kconfig: Kill
PPC_MULTIPLATFORM") broke KEXEC, by making it dependent on BOOK3S, while it
should be PPC_BOOK3S.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

When we call giveup_fpu, we need to need to turn off VSX for the
current process.  If we don't, on return to userspace it may execute a
VSX instruction before the next FP instruction, and not have its
register state refreshed correctly from the thread_struct.  Ditto for
altivec.

This caused a bug where an unaligned lfs or stfs results in
fix_alignment calling giveup_fpu so it can use the FPRs (in order to
do a single <-> double conversion), and then returning to userspace
with FP off but VSX on.  Then if a VSX instruction is executed, before
another FP instruction, it will proceed without another exception and
hence have the incorrect register state for VSX registers 0-31.

   lfs unaligned   <- alignment exception turns FP off but leaves VSX on

   VSX instruction <- no exception since VSX on, hence we get the
                      wrong VSX register values for VSX registers 0-31,
                      which overlap the FPRs.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Enable relay in pseries config, ppc64_defconfig had it enabled but pseries
did not.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We specify a 64MB RMO, but the comment says 128MB.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Instead of checking for known events, pass in all 1s so we handle future
event types.  We were currently missing the IO event type.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

PHYP tells us how often a shared processor dispatch changed physical cpus.
This can highlight performance problems caused by the hypervisor.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Make all messages consistent, some have spaces before the "...", some do not.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The ibm,client-architecture method will often cause a reconfiguration reboot.
When this happens the last thing we see is:

	Hypertas detected, assuming LPAR !

Which doesn't explain what just happened.  Wrap the ibm,client-architecture
so it's clear what is going on:

	Calling ibm,client-architecture... done

In order to maintain the law of conservation of screen real estate, downgrade
two other messages to debug.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Remove duplicated #include's in
  - arch/powerpc/include/asm/ps3fb.h
  - arch/powerpc/kernel/setup-common.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add support for CMOS Sensor Interface on i.MX1 and i.MXL SoCs.

 create mode 100644 arch/arm/mach-mx1/ksym_mx1.c
 create mode 100644 arch/arm/mach-mx1/mx1_camera_fiq.S
 create mode 100644 arch/arm/plat-mxc/include/mach/mx1_camera.h
 create mode 100644 drivers/media/video/mx1_camera.c
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: NDarius Augulis <augulis.darius@gmail.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With the i.MX31 transition to clkdev clock names have changed, but mistakenly
the "mx3-camera.0" has been registered with a non-NULL connection ID, which is
not necessary, since this is the only clock, used by the capture interface
driver. Fix the clock definition and the driver to use NULL as a connection ID.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes the follwing build error caused by
commit 7ca43e75
(mm: use debug_kmap_atomic):

  ...
    AS      arch/frv/mm/tlb-miss.o
  In file included from
  arch/frv/mm/tlb-miss.S:13:
  ...
  Assembler messages:
  include/asm-generic/ioctl.h:73:
  Error: unrecognized instruction `extern unsigned int __invalid_size_argument_for_IO...'
  ...
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds multi-chip support for the Micron MT29F8G08FAB NAND
flash memory on the TQM8548 modules.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. This requires support for multiple GPIOs for the RNB pins.
The NAND chips are selected through address lines defined by the
FDT property "fsl,upm-addr-line-cs-offsets".
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Acked-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add aliases, and correct CS0 offset to match how u-boot
programs it (this was not a problem with cuImage because
the wrapper would reprogram the localbus to match the device
tree).
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

CoreInt provides a mechansim to deliver the IRQ vector directly
into the core on an interrupt (via the SPR EPR) rather than having
to go IACK on the PIC.  This is suppose to provide an improvment
in interrupt latency by reducing the time to get the IRQ vector.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>