Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 14 8月, 2009 29 次提交
  3. 13 8月, 2009 5 次提交
    • N
      md: allow upper limit for resync/reshape to be set when array is read-only · 4d484a4a
      由 NeilBrown 提交于 
      Normally we only allow the upper limit for a reshape to be decreased
when the array not performing a sync/recovery/reshape, otherwise there
could be races.  But if an array is part-way through a reshape when it
is assembled the reshape is started immediately leaving no window
to set an upper bound.

If the array is started read-only, the reshape will be suspended until
the array becomes writable, so that provides a window during which it
is perfectly safe to reduce the upper limit of a reshape.

So: allow the upper limit (sync_max) to be reduced even if the reshape
thread is running, as long as the array is still read-only.
Signed-off-by: NNeilBrown <neilb@suse.de>
      4d484a4a
    • N
      md/raid5: Properly remove excess drives after shrinking a raid5/6 · 1a67dde0
      由 NeilBrown 提交于 
      We were removing the drives, from the array, but not
removing symlinks from /sys/.... and not marking the device
as having been removed.
Signed-off-by: NNeilBrown <neilb@suse.de>
      1a67dde0
    • N
      md/raid5: make sure a reshape restarts at the correct address. · a639755c
      由 NeilBrown 提交于 
      This "if" don't allow for the possibility that the number of devices
doesn't change, and so sector_nr isn't set correctly in that case.
So change '>' to '>='.
Signed-off-by: NNeilBrown <neilb@suse.de>
      a639755c
    • N
      md/raid5: allow new reshape modes to be restarted in the middle. · 67ac6011
      由 NeilBrown 提交于 
      md/raid5 doesn't allow a reshape to restart if it involves writing
over the same part of disk that it would be reading from.
This happens at the beginning of a reshape that increases the number
of devices, at the end of a reshape that decreases the number of
devices, and continuously for a reshape that does not change the
number of devices.

The current code is correct for the "increase number of devices"
case as the critical section at the start is handled by userspace
performing a backup.

It does not work for reducing the number of devices, or the
no-change case.
For 'reducing', we need to invert the test.  For no-change we cannot
really be sure things will be safe, so simply require the array
to be read-only, which is how the user-space code which carefully
starts such arrays works.
Signed-off-by: NNeilBrown <neilb@suse.de>
      67ac6011
    • N
      md: never advance 'events' counter by more than 1. · 51d5668c
      由 NeilBrown 提交于 
      When assembling arrays, md allows two devices to have different event
counts as long as the difference is only '1'.  This is to cope with
a system failure between updating the metadata on two difference
devices.

However there are currently times when we update the event count by
2.  This was done to keep the event count even when the array is clean
and odd when it is dirty, which allows us to avoid writing common
update to spare devices and so allow those spares to go to sleep.

This is bad for the above reason.  So change it to never increase by
two.  This means that the alignment between 'odd/even' and
'clean/dirty' might take a little longer to attain, but that is only a
small cost.  The spares will get a few more updates but that will
still be spared (;-) most updates and can still go to sleep.

Prior to this patch there was a small chance that after a crash an
array would fail to assemble due to the overly large event count
mismatch.
Signed-off-by: NNeilBrown <neilb@suse.de>
      51d5668c
  5. 12 8月, 2009 6 次提交