Reported-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: NKeith Packard <keithp@keithp.com>

We were using uninitialised watermarks values for disabled pipes which
were combined into a single WM register and so corrupting the values for
the enabled pipe and upsetting the display hardware.
Reported-by: NRiccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32612Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Similar to booting, we need to inspect the state left by the BIOS and
remove any conflicting bits before we take over. The example reported by
Seth Forshee is very similar to the bug we encountered with the state left
by grub2, that the crtc pipe<->planning mapping was reversed from our
expectations and so we failed to turn off the outputs when booting or,
in this case, resuming. This may be in fact the same bug, but triggered
at resume time.

This patch rearranges the code we already have to clear up the
conflicting state upon init and calls it from reset (which is called
after we have lost control of the hardware, i.e. along both the boot and
resume paths) instead.
Reported-and-tested-by: NSeth Forshee <seth.forshee@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35796Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Reviewed-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Fix up the debug file to report the right frequencies.  On SNB, we program
the PCU with a frequency ratio, which is multiplied by 100MHz on the CPU
side.  But GFX only runs at half that, so report it as such to avoid
confusion.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NKeith Packard <keithp@keithp.com>

A broken implementation of is_pot() prevented the detection of when a
singular pipe was enabled. Eric Anholt pointed out the existence of
is_power_of_2() so use that instead of our broken code!

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35402Signed-off-by: NYuanhan Liu <yuanhan.liu@intel.com>
Tested-by: xunx.fang@intel.com
Reviewed-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

If the pipe or plane is already enabled, then we do not need to enable
it again and can skip the delay. Similarly if it is already disabled
when we want to disable it, we can also skip it.

This fixes a regression from b24e7179, which caused the LVDS
output on one PineView machine to become corrupt after changing
orientation several times.

References: https://bugs.freedesktop.org/show_bug.cgi?id=34601
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NKeith Packard <keithp@keithp.com>
Tested-by: mengmeng.meng@intel.com

... as wait_for_vblank (and friends) will do a flush of the MMIO writes
anyway.

References: https://bugs.freedesktop.org/show_bug.cgi?id=34601
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Whilst the GT is powered down (rc6), writes to MMADDR are placed in a
FIFO by the System Agent. This is a limited resource, only 64 entries, of
which 20 are reserved for Display and PCH writes, and so we must take
care not to queue up too many writes. To avoid this, there is counter
which we can poll to ensure there are sufficient free entries in the
fifo.

"Issuing a write to a full FIFO is not supported; at worst it could
result in corruption or a system hang."
Reported-and-Tested-by: NMatt Turner <mattst88@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34056Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

After disabling, we're meant to teardown the bo used for the contexts,
not recurse into ourselves again and preventing module unload.
Reported-and-tested-by: NBen Widawsky <bwidawsk@gmail.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The code paths for modesetting are growing in complexity as we may need
to move the buffers around in order to fit the scanout in the aperture.
Therefore we face a choice as to whether to thread the interruptible status
through the entire pinning and unbinding code paths or to add a flag to
the device when we may not be interrupted by a signal. This does the
latter and so fixes a few instances of modesetting failures under stress.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Dave Airlie spotted that we had a potential bug should we ever rearrange
the drm_i915_gem_object so not the base drm_gem_object was not its first
member. He noticed that we often convert the return of
drm_gem_object_lookup() immediately into drm_i915_gem_object and then
check the result for nullity. This is only valid when the base object is
the first member and so the superobject has the same address. Play safe
instead and use the compiler to convert back to the original return
address for sanity testing.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

In a few places I replaced reads of per-pipe registers with the actual
register offsets themselves (converting I915_READ(reg) to _PIPE(reg)).
Alexey caught this on his 9xx machine because the cursor control write
was affected.  A quick audit showed a few more places where I'd borked
a read, so here's a patch to fix things up.
Reported-by: NAlexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[ickle: compilation fix]
Tested-by: NAlexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This reverts commit 633f2ea2 and the
attempted fix dcbe6f2b.

There is a single clock source used for both SSC (some LVDS and DP) and
non-SSC (VGA, DVI) outputs. So we need to be careful to only enable SSC
as necessary. However, fiddling with DREFCLK was causing DP links to be
dropped and we do not have a fix ready, so revert.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

eDP on the CPU doesn't need the PCH set up at all, it can in fact cause
problems.  So avoid FDI training and PCH PLL enabling in that case.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

If the gpu is hung, then whatever was inside the render cache is lost
and there is little point waiting for it. Or complaining if we see an
EIO or EAGAIN instead. So, if the GPU is indeed in its death throes when
we need to rewrite the registers for a new framebuffer, just ignore the
error and proceed with the update.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

If the gpu is hung, then whatever was inside the render cache is lost
and there is little point waiting for it. Or complaining if we see an
EIO or EAGAIN instead. So, if the GPU is indeed in its death throes when
we need to rewrite the registers for a new framebuffer, just ignore the
error and proceed with the update.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Disable any PCH ports associated with a pipe when disabling it.  This
should prevent transcoder disable failures due to ports still being on.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[ickle: introduce *_PIPE_ENABLED() macro]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The irony of the patch to fix the resume regression on PineView causing
a further regression on Ironlake is not lost on me.
Reported-by: NJeff Chua <jeff.chua.linux@gmail.com>
Reported-by: NBjörn Schließmann <chronoss@gmx.de>
Tested-by: NBjörn Schließmann <chronoss@gmx.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28802Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The automatic powersaving feature is once again causing havoc, with 100%
reliable hangs on boot and resume on affected machines.
Reported-by: NFrancesco Allertsen <fallertsen@gmail.com>
Reported-by: NGui Rui <chaos.proton@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28582Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

We had some conversions over to the _PIPE macros, but didn't get
everything.  So hide the per-pipe regs with an _ (still used in a few
places for legacy) and add a few _PIPE based macros, then make sure
everyone uses them.

[update: remove usage of non-existent no-op macro]
[update 2: keep modesetting suspend/resume code, update to new reg names]
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[ickle: stylistic cleanups for checkpatch and taste]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The PCH can drive several reference clocks simultaneously, and needs to
with multiple display configurations.  So we can't just clobber the
existing state everytime we set a mode, we need to take into account
what the other CRTCs are doing at the time.

Doing so fixes an issue where you'd lose the LVDS display at boot if you
had an LVDS+DP config.

[updated: init bools and check CRTC status correctly]
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

When a transcoder is disabled, any ports pointing at it should also be
disabled.  If they're not, we may fail to disable the transcoder,
leading to blank displays.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

These bits have a different meaning on ILK+, where planes are hardwired
to pipes.  Fixing this avoid some spurious assertion failures.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The specs say to do so.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

For consistency and segregation from the noisy DRM_DEBUG().
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Fortunately unreachable. For Crestline, the watermarks must always be
programmed to 8...
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Based on a patch by Takashi Iwai.
Reported-by: NMatthias Hopf <mat@mshopf.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=27272Tested-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Move the plane->mode config to the point of use rather than repeatedly
querying the same information.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Reports of FIFO underruns are still persisting on gm45.

References: https://bugs.freedesktop.org/show_bug.cgi?id=27589Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

For CRT and SDVO/HDMI, we need to use a normal, non-SSC, clock and so we
must clear any enabling bits left-over from earlier outputs. And also
seems to correct the LVDS panel on the Lenovo U160.

However, at one point, it did cause an "ERROR failed to disable
trancoder". So prolonged testing on top of Jesse's refactored and
error-checking CRTC logic is desired.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The i915 driver normally assumes the video bios has configured several
of the LVDS panel registers, and it just inherits the values. If the
vbios has not run, several of these will need to be setup. So we need to
check that the LVDS sync polarity is correctly configured per any
available modelines (e.g. EDID) and adjust if not, issuing a warning as
we do.
Signed-off-by: NMark Hayter <mdhayter@chromium.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

These make us increase our frequency much more readily, and decrease
them only after significant idle time, resulting in a 20% performance
increase for nexuiz.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Move code around and invoke iomem annotation in a few more places in
order to silence sparse. Still a few more iomem annotations to go...
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

I changed 945's self refresh to work without the need for the driver to
enable/disable self refresh manually based on the idle state of the gpu.
This is much better than enabling/disabling self refresh for various
reasons, including staying in a lower power state for more time and
avoiding the need for cpu cycles.

This was originally done manually to workaround issues with the hardware
hanging. However, since 94400120: drm/i915: enable low power render
writes on GEN3 hardware, automatic CxSR seems stable.
Signed-off-by: NAlexander Lam <lambchop468@gmail.com>
Acked-by : Li Peng <peng.li@linux.intel.com>
[ickle: play safe with the ordering and disable CxSR before tweaking any
watermark and enable afterwards.]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

eDP on the CPU doesn't need the PCH set up at all, it can in fact cause
problems.  So avoid FDI training and PCH PLL enabling in that case.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NYuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

We need to unlock the phase sync pointer enable bit before we can
actually enable the phase sync pointer workaround on Ironlake.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Factor out the FDI disable function (make it a mirror of
ironlake_fdi_enable) and add some FDI related assertions to the FDI
training code (we need an active pipe & plane before we start
transmitting bits).
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Along with assertion checks for the FDI transmitters and receivers
(including PLLs).  Modify the pipe enable function to check for FDI PLL
status as well, when driving PCH ports.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>