iWARP has different physical queue requirements than RoCE
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When computing how much memory is required for the different hw clients
iWARP protocol should be taken into account
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces error handling for errors that occurred during
connection establishment.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch takes care of active/passive disconnect flows.
Disconnect flows can be initiated remotely, in which case a async event
will arrive from peer and indicated to qedr driver. These
are referred to as exceptions. When a QP is destroyed, it needs to check
that it's associated ep has been closed.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the active side connect.
Offload a connection, process MPA reply and send RTR.
In some of the common passive/active functions, the active side
will work in blocking mode.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the passive side connect.
It addresses pre-allocating resources, creating a connection
element upon valid SYN packet received. Calling upper layer and
implementation of the accept/reject calls.

Error handling is not part of this patch.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the ability to add and remove listeners and identify
whether the SYN packet received is intended for iWARP or not. If
a listener is not found the SYN packet is posted back to the chip.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

iWARP handles incoming SYN packets using the ll2 interface. This patch
implements ll2 setup and teardown. Additional ll2 connections will
be used in the future which are not part of this patch series.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new connection type for iWARP ll2 connections for setting
correct ll2 filters and connection type to FW.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make some names more generic as they will be used by iWARP too.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds iWARP support for flows that have common code
between RoCE and iWARP, such as initialization, teardown and
qp setup verbs: create, destroy, modify, query.
It introduces the iWARP specific files qed_iwarp.[ch] and
iwarp_common.h
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

iWARP personality introduced the need for differentiating in several
places in the code whether we are RoCE, iWARP or either. This
leads to introducing new macros for querying the personality.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix out-of-date comment.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in mlx5_core_dbg debug message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NIlan Tayari <ilant@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously the flower offloads never sends messages to the hardware,
and never registers a handler for receiving messages from hardware.
This patch enables the flower offloads to send control messages to
hardware when adding and removing flow rules. Additionally it
registers a control message rx handler for receiving stats updates
from hardware for each offloaded flow.

Additionally this patch adds 4 control message types; Add, modify and
delete flow, as well as flow stats. It also allows
nfp_flower_cmsg_get_data() to be used outside of cmsg.c.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously there was no way of updating flow rule stats after they
have been offloaded to hardware. This is solved by keeping track of
stats received from hardware and providing this to the TC handler
on request.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds metadata describing the mask id of each flow and keeps track of
flows installed in hardware. Previously a flow could not be removed
from hardware as there was no way of knowing if that a specific flow
was installed. This is solved by storing the offloaded flows in a
hash table.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds push vlan, pop vlan, output and drop action capabilities
to flower offloads.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extends matching capabilities for flower offloads to include vlan,
layer 2, layer 3 and layer 4 type matches. This includes both exact
and wildcard matching.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extends the flower flow add function by calculating which match
fields are present in the flower offload structure and allocating
the appropriate space to describe these.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds a flower based TC offload handler for representor devices, this
is in addition to the bpf based offload handler. The changes in this
patch will be used in a follow-up patch to add tc flower offload to
the NFP.

The flower app enables tc offloads on representors by default.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add phys_switch_id support by allowing lookup of
SWITCHDEV_ATTR_ID_PORT_PARENT_ID via the nfp_repr_port_attr_get
switchdev operation.

This is visible to user-space in the phys_switch_id attribute
of a netdev.

e.g.

cd /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0
find . -name phys_switch_id | xargs grep .
./net/eth3/phys_switch_id:00154d1300bd
./net/eth4/phys_switch_id:00154d1300bd
./net/eth2/phys_switch_id:00154d1300bd
grep: ./net/eth5/phys_switch_id: Operation not supported

In the above eth2 and eth3 and representor netdevs for the first and second
physical port. eth4 is the representor for the PF. And eth5 is the PF netdev.
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is based on original Harini's patch and Andrei's patch,
implemented in a separate file to ease the review/maintanance
and integration with other platforms.

This driver supports GEM-GXL:
- Register ptp clock framework
- Initialize PTP related registers
- HW time stamp on the PTP Ethernet packets are received using the
  SO_TIMESTAMPING API. Time stamps are obtained from the dma buffer
  descriptors
- add macb_ptp to compilation chain
Signed-off-by: NRafal Ozieblo <rafalo@cadence.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case that macb is compiled as a module, macb.c has been renamed to
macb_main.c to avoid naming confusion in Makefile.
Signed-off-by: NRafal Ozieblo <rafalo@cadence.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for PTP timestamps in
DMA buffer descriptors. It checks capability at runtime
and uses appropriate buffer descriptor.
Signed-off-by: NRafal Ozieblo <rafalo@cadence.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When filter insertion fails with no rollback, we were trying to convert
 EFX_EF10_FILTER_ID_INVALID to an id to store in 'ids' (which is either
 vlan->uc or vlan->mc).  This would WARN_ON_ONCE and then record a bogus
 filter ID of 0x1fff, neither of which is a good thing.

Fixes: 0ccb998b ("sfc: fix filter_id misinterpretation in edge case")
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the number of TX queues that are allocated doesn't depend
on the number of TCs, the module always loads with max num of UP
per channel.
In order to prevent the allocation of unnecessary memory, the
module will load with minimum number of UPs per channel, and the
user will be able to control the number of TX queues per channel
by changing the number of TC to 8 using the tc command.
The variable num_up will hold the information about the current
number of UPs.
Due to the change, needed to remove the lines that set the value of
UP to be different than zero in the func "mlx4_en_select_queue",
since now the num of TX queues that are allocated is only one per channel
in default.
In order not to force the UP to be zero in case of only one TC, added
a condition before forcing it in the func "mlx4_en_fill_qp_context".

Tested:
After the module is loaded with minimum number of UP per channel, to
increase num of TCs to 8, use:
tc qdisc add dev ens8 root mqprio num_tc 8
In order to decrease the number of TCs to minimum number of UP per channel,
use:
tc qdisc del dev ens8 root
Signed-off-by: NInbar Karmy <inbark@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Cc: Tarick Bedeir <tarick@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until this patch, the number of UPs was hard coded for eight.
Replace this with a variable in struct "mlx4_en_port_profile".
Currently, the variable will hold the maximum number of UP,
as before.
The patch creates an infrastructure to add an option for dynamic
change of the actual number of TCs.
Signed-off-by: NInbar Karmy <inbark@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Cc: Tarick Bedeir <tarick@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.

File size before:
   text	   data	    bss	    dec	    hex	filename
  19057	    392	      0	  19449	   4bf9	drivers/net/ethernet/freescale/gianfar.o

File size After adding 'const':
   text	   data	    bss	    dec	    hex	filename
  19249	    192	      0	  19441	   4bf1	drivers/net/ethernet/freescale/gianfar.o
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.

File size before:
   text	   data	    bss	    dec	    hex	filename
  18709	    401	      0	  19110	   4aa6	drivers/net/ethernet/smsc/smc91x.o

File size After adding 'const':
   text	   data	    bss	    dec	    hex	filename
  18901	    201	      0	  19102	   4a9e	drivers/net/ethernet/smsc/smc91x.o
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.

File size before:
   text	   data	    bss	    dec	    hex	filename
  15426	   1256	      0	  16682	   412a	drivers/net/ethernet/ibm/ibmveth.o

File size After adding 'const':
   text	   data	    bss	    dec	    hex	filename
  15618	   1064	      0	  16682	   412a	drivers/net/ethernet/ibm/ibmveth.o
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver currently creates RX/TX queues during device probe, but
assigns IRQ's to them during device open. On reset, however,
IRQ's are assigned when resetting the queues. If there is a reset
while the device is closed and the device is later opened, the driver will
request IRQ's twice, causing the open to fail. This patch assigns
the IRQ's in the ibmvnic_init function after the queues are reset or
initialized, ensuring IRQ's are only requested once.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in netdev_err message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to change some general performance settings and to provide
some performance settings based on the device that is probed.

This includes:

- Setting the maximum read/write outstanding request limit
- Reducing the AXI interface burst length size
- Selectively setting the Tx and Rx descriptor pre-fetch threshold
- Selectively setting additional cache coherency controls

Tested and verified on all versions of the hardware.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the driver hardcodes the PBLx8 setting.  Remove the need for
specifying the PBLx8 setting and automatically calculate based on the
specified PBL value. Since the PBLx8 setting applies to both Tx and Rx
use the same PBL value for both of them.

Also, the driver currently uses a bit field to set the AXI master burst
len setting. Change to the full bit field range and set the burst length
based on the specified value.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In prep for setting fine grained read and write DMA cache coherency
controls, allow specific values to be used to set the cache coherency
registers.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For IRQ affinity, set the affinity hints for the IRQs to be (initially) on
the processors corresponding to the NUMA node of the device.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to perform memory allocations on the node of the device. The
original allocation or the ring structure and Tx/Rx queues allocated all
of the memory at once and then carved it up for each channel and queue.
To best ensure that we get as much memory from the NUMA node as we can,
break the channel and ring allocations into individual allocations.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the device interrupts should function as level interrupts. For
some hardware configurations this requires setting some control bits
so that if the interrupt status has not been cleared the interrupt
should be reissued.

Additionally, when using MSI or MSI-X interrupts, run the interrupt
service routine as a tasklet so that the re-issuance of the interrupt
is handled properly.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>