Since the watchdog code in sch56xx-common now uses the watchdog core, the
Kconfig entires for the sch5627 and sch5636 should depend on WATCHDOG
being set. Also select the watchdog core when we select one of the drivers.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

WDOG_NO_WAY_OUT (3) and WDOG_ACTIVE (0) are the bit numbers, not a mask.
So "data->wddev.status |= WDOG_ACTIVE;" was intended to set bit zero but
it is a no-op.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This driver adds support for the watchdog functionality provided by
the Dialog Semiconductor DA9052 PMIC chip.

Tested on samsung smdkv6410 and i.mx53 QS boards.
Signed-off-by: NAnthony Olech <Anthony.Olech@diasemi.com>
Signed-off-by: NAshish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This fixes referencing free-ed memory in the corner case where /dev/watchdog
is open when the platform driver gets unbound from the platform device.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Since the watchdog core keeps track of the watchdog's active state, start/stop
will never get called when no changes are necessary. So we can remove the
check for the output_enable register changing before writing it (which is
an expensive operation).
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Convert sch56xx drivers to the generic watchdog core.

Note this patch depends on the "watchdog: Add multiple device support" patch
from Alan Cox.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

If a driver's watchdog_device struct is part of a dynamically allocated
struct (which it often will be), merely locking the module is not enough,
even with a drivers module locked, the driver can be unbound from the device,
examples:
1) The root user can unbind it through sysfd
2) The i2c bus master driver being unloaded for an i2c watchdog

I will gladly admit that these are corner cases, but we still need to handle
them correctly.

The fix for this consists of 2 parts:
1) Add ref / unref operations, so that the driver can refcount the struct
   holding the watchdog_device struct and delay freeing it until any
   open filehandles referring to it are closed
2) Most driver operations will do IO on the device and the driver should not
   do any IO on the device after it has been unbound. Rather then letting each
   driver deal with this internally, it is better to ensure at the watchdog
   core level that no operations (other then unref) will get called after
   the driver has called watchdog_unregister_device(). This actually is the
   bulk of this patch.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This patch fixes some potential multithreading issues, despite only
allowing one process to open the /dev/watchdog device, we can still get
called multiple times at the same time, since a program could be using thread,
or could share the fd after a fork.

This causes 2 potential problems:
1) watchdog_start / open do an unlocked test_n_set / test_n_clear,
   if these 2 race, the watchdog could be stopped while the active
   bit indicates it is running or visa versa.

2) Most watchdog_dev drivers probably assume that only one
   watchdog-op will get called at a time, this is not necessary
   true atm.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Rewrite and extend the wrapper code so that we can easily introduce
locking (this to be able to prevent potential multithreading issues).
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

While they are registered all our watchdogs now have a valid device object
so we can in turn use that to report problems nicely.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Create the watchdog class and it's associated devices.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Some watchdogs merely trigger external alarms and controls. In a managed
environment this is very useful but we want drivers to be able to figure
out which is which now multiple dogs can be loaded. Thus add an ALARMONLY
feature flag.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

We keep the old /dev/watchdog interface file for the first watchdog via
miscdev. This is basically a cut and paste of the relevant interface code
from the rtc driver layer tweaked for watchdog.

Revised to fix problems noted by Hans de Goede
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Make the functions in watchdog_core.h extern like it should.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

The watchdog_core include file should have been named
watchdog_core.h and not watchdog_dev.h . Correct this.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Some watchdog may need to check if watchdog is ACTIVE or not, for example in
their suspend/resume hooks.

This patch adds this routine and changes the core drivers to use it.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Include the private watchdog_dev.h header to pickup the prototypes for the
watchdog_dev_register/unregister functions.

This quiets the following sparse warnings:

warning: symbol 'watchdog_dev_register' was not declared. Should it be static?
warning: symbol 'watchdog_dev_unregister' was not declared. Should it be static?
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Pull x86 trampoline rework from H. Peter Anvin:
 "This code reworks all the "trampoline"/"realmode" code (various bits
  that need to live in the first megabyte of memory, most but not all of
  which runs in real mode at some point) in the kernel into a single
  object.  The main reason for doing this is that it eliminates the last
  place in the kernel where we needed pages to be mapped RWX.  This code
  separates all that code into proper R/RW/RX pages."

Fix up conflicts in arch/x86/kernel/Makefile (mca removed next to reboot
code), and arch/x86/kernel/reboot.c (reboot code moved around in one
branch, modified in this one), and arch/x86/tools/relocs.c (mostly same
code came in earlier due to working around the ld bugs just before the
3.4 release).

Also remove stale x86-relocs entry from scripts/.gitignore as per Peter
Anvin.

* commit '61f54461': (36 commits)
  x86, realmode: Move end signature into header.S
  x86, relocs: When printing an error, say relative or absolute
  x86, relocs: More relocations which may end up as absolute
  x86, relocs: Workaround for binutils 2.22.52.0.1 section bug
  xen-acpi-processor: Add missing #include <xen/xen.h>
  acpi, bgrd: Add missing <linux/io.h> to drivers/acpi/bgrt.c
  x86, realmode: Change EFER to a single u64 field
  x86, realmode: Move kernel/realmode.c to realmode/init.c
  x86, realmode: Move not-common bits out of trampoline_common.S
  x86, realmode: Mask out EFER.LMA when saving trampoline EFER
  x86, realmode: Fix no cache bits test in reboot_32.S
  x86, realmode: Make sure all generated files are listed in targets
  x86, realmode: build fix: remove duplicate build
  x86, realmode: read cr4 and EFER from kernel for 64-bit trampoline
  x86, realmode: fixes compilation issue in tboot.c
  x86, realmode: move relocs from scripts/ to arch/x86/tools
  x86, realmode: header for trampoline code
  x86, realmode: flattened rm hierachy
  x86, realmode: don't copy real_mode_header
  x86, realmode: fix 64-bit wakeup sequence
  ...

Pull EDAC internal API changes from Mauro Carvalho Chehab:
 "This changeset is the first part of a series of patches that fixes the
  EDAC sybsystem.  On this set, it changes the Kernel EDAC API in order
  to properly represent the Intel i3/i5/i7, Xeon 3xxx/5xxx/7xxx, and
  Intel E5-xxxx memory controllers.

  The EDAC core used to assume that:

       - the DRAM chip select pin is directly accessed by the memory
         controller

       - when multiple channels are used, they're all filled with the
         same type of memory.

  None of the above premises is true on Intel memory controllers since
  2002, when RAMBUS and FB-DIMMs were introduced, and Advanced Memory
  Buffer or by some similar technologies hides the direct access to the
  DRAM pins.

  So, the existing drivers for those chipsets had to lie to the EDAC
  core, in general telling that just one channel is filled.  That
  produces some hard to understand error messages like:

       EDAC MC0: CE row 3, channel 0, label "DIMM1": 1 Unknown error(s): memory read error on FATAL area : cpu=0 Err=0008:00c2 (ch=2), addr = 0xad1f73480 => socket=0, Channel=0(mask=2), rank=1

  The location information there (row3 channel 0) is completely bogus:
  it has no physical meaning, and are just some random values that the
  driver uses to talk with the EDAC core.  The error actually happened
  at CPU socket 0, channel 0, slot 1, but this is not reported anywhere,
  as the EDAC core doesn't know anything about the memory layout.  So,
  only advanced users that know how the EDAC driver works and that tests
  their systems to see how DIMMs are mapped can actually benefit for
  such error logs.

  This patch series fixes the error report logic, in order to allow the
  EDAC to expose the memory architecture used by them to the EDAC core.
  So, as the EDAC core now understands how the memory is organized, it
  can provide an useful report:

       EDAC MC0: CE memory read error on DIMM1 (channel:0 slot:1 page:0x364b1b offset:0x600 grain:32 syndrome:0x0 - count:1 area:DRAM err_code:0001:0090 socket:0 channel_mask:1 rank:4)

  The location of the DIMM where the error happened is reported by "MC0"
  (cpu socket #0), at "channel:0 slot:1" location, and matches the
  physical location of the DIMM.

  There are two remaining issues not covered by this patch series:

       - The EDAC sysfs API will still report bogus values.  So,
         userspace tools like edac-utils will still use the bogus data;

       - Add a new tracepoint-based way to get the binary information
         about the errors.

  Those are on a second series of patches (also at -next), but will
  probably miss the train for 3.5, due to the slow review process."

Fix up trivial conflict (due to spelling correction of removed code) in
drivers/edac/edac_device.c

* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (42 commits)
  i7core: fix ranks information at the per-channel struct
  i5000: Fix the fatal error handling
  i5100_edac: Fix a warning when compiled with 32 bits
  i82975x_edac: Test nr_pages earlier to save a few CPU cycles
  e752x_edac: provide more info about how DIMMS/ranks are mapped
  i5000_edac: Fix the logic that retrieves memory information
  i5400_edac: improve debug messages to better represent the filled memory
  edac: Cleanup the logs for i7core and sb edac drivers
  edac: Initialize the dimm label with the known information
  edac: Remove the legacy EDAC ABI
  x38_edac: convert driver to use the new edac ABI
  tile_edac: convert driver to use the new edac ABI
  sb_edac: convert driver to use the new edac ABI
  r82600_edac: convert driver to use the new edac ABI
  ppc4xx_edac: convert driver to use the new edac ABI
  pasemi_edac: convert driver to use the new edac ABI
  mv64x60_edac: convert driver to use the new edac ABI
  mpc85xx_edac: convert driver to use the new edac ABI
  i82975x_edac: convert driver to use the new edac ABI
  i82875p_edac: convert driver to use the new edac ABI
  ...

Pull MIPS updates from Ralf Baechle:
 "The whole series has been sitting in -next for quite a while with no
  complaints.  The last change to the series was before the weekend the
  removal of an SPI patch which Grant - even though previously acked by
  himself - appeared to raise objections.  So I removed it until the
  situation is clarified.  Other than that all the patches have the acks
  from their respective maintainers, all MIPS and x86 defconfigs are
  building fine and I'm not aware of any problems introduced by this
  series.

  Among the key features for this patch series is a sizable patchset for
  Lantiq which among other things introduces support for Lantiq's
  flagship product, the FALCON SOC.  It also means that the opensource
  developers behind this patchset have overtaken Lantiq's competing
  inhouse development team that was working behind closed doors.

  Less noteworthy the ath79 patchset which adds support for a few more
  chip variants, cleanups and fixes.  Finally the usual dose of tweaking
  of generic code."

Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
  MIPS: lantiq: remove orphaned code
  MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
  MIPS: lantiq: implement support for FALCON soc
  MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
  MTD: MIPS: lantiq: implement OF support
  watchdog: MIPS: lantiq: implement OF support and minor fixes
  SERIAL: MIPS: lantiq: implement OF support
  GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
  GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
  GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
  MIPS: pci: convert lantiq driver to OF
  MIPS: lantiq: convert dma to platform driver
  MIPS: lantiq: implement support for clkdev api
  MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
  OF: MIPS: lantiq: implement irq_domain support
  OF: MIPS: lantiq: implement OF support
  MIPS: lantiq: drop mips_machine support
  OF: PCI: const usage needed by MIPS
  MIPS: Cavium: Remove smp_reserve_lock.
  MIPS: Move cache setup to setup_arch().
  ...

Pull arm updates from Russell King:
 "This contains both some fixes found when trying to get the
  Assabet+neponset setup as a replacement firewall with a 3c589 PCMCIA
  card, and a bunch of changes from Al to fix up the ARM signal
  handling, particularly some of the restart behaviour."

* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: neponset: make sure neponset_ncr_frob() is exported
  ARM: fix out[bwl]()
  arm: don't open-code ptrace_report_syscall()
  arm: bury unused _TIF_RESTORE_SIGMASK
  arm: remove unused restart trampoline
  arm: new way of handling ERESTART_RESTARTBLOCK
  arm: if we get into work_pending while returning to kernel mode, just go away
  arm: don't call try_to_freeze() from do_signal()
  arm: if there's no handler we need to restore sigmask, syscall or no syscall
  arm: trim _TIF_WORK_MASK, get rid of useless test and branch...
  arm: missing checks of __get_user()/__put_user() return values

Merge patches through Andrew Morton:
 "180 patches - err 181 - listed below:

   - most of MM.  I held back the (large) "memcg: add hugetlb extension"
     series because a bunfight has recently broken out.

   - leds.  After this, Bryan Wu will be handling drivers/leds/

   - backlight

   - lib/

   - rtc"

* emailed from Andrew Morton <akpm@linux-foundation.org>: (181 patches)
  drivers/rtc/rtc-s3c.c: fix compiler warning
  drivers/rtc/rtc-tegra.c: clean up probe/remove routines
  drivers/rtc/rtc-pl031.c: remove RTC timer interrupt handling
  drivers/rtc/rtc-lpc32xx.c: add device tree support
  drivers/rtc/rtc-m41t93.c: don't let get_time() reset M41T93_FLAG_OF
  rtc: ds1307: add trickle charger support
  rtc: ds1307: remove superfluous initialization
  rtc: rename CONFIG_RTC_MXC to CONFIG_RTC_DRV_MXC
  drivers/rtc/Kconfig: place RTC_DRV_IMXDI and RTC_MXC under "on-CPU RTC drivers"
  drivers/rtc/rtc-pcf8563.c: add RTC_VL_READ/RTC_VL_CLR ioctl feature
  rtc: add ioctl to get/clear battery low voltage status
  drivers/rtc/rtc-ep93xx.c: convert to use module_platform_driver()
  rtc/spear: add Device Tree probing capability
  lib/vsprintf.c: "%#o",0 becomes '0' instead of '00'
  radix-tree: fix preload vector size
  spinlock_debug: print kallsyms name for lock
  vsprintf: fix %ps on non symbols when using kallsyms
  lib/bitmap.c: fix documentation for scnprintf() functions
  lib/string_helpers.c: make arrays static
  lib/test-kstrtox.c: mark const init data with __initconst instead of __initdata
  ...

rtc-s3c.c:673:32: warning: `s3c_rtc_drv_data_array' defined but not used [-Wunused-variable]
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the devres managed resource functions in the probe routine.  Also
affects the remove routine where the previously used free and release
functions are not needed.

The devm_* functions eliminate the need for manual resource releasing and
simplify error handling.  Resources allocated by devm_* are freed
automatically on driver detach.
Signed-off-by: NHannu Heikkinen <ext-hannu.m.heikkinen@nokia.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove RTT interrupt handling, since PIE mode interrupts are now better
emulated in generic code via an hrtimer we have no need for this, and
there is no codepath in the driver that enables these periodic interrupts
anyway.
Signed-off-by: NRajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Adds device tree support for rtc-lpc32xx.c
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the rtc reports the time might be invalid due to oscillator failure,
M41T93_FLAG_OF flag must not be reset by get_time() as the read operation
doesn't make the time valid.

Without this patch, only the first get_time() reported an invalid time,
the second get_time() reported a valid time althought the reported time is
probably wrong due to oscillator failure.

Instead of resetting in get_time(), with this patch M41T93_FLAG_OF is
reset in set_time() when a valid time is to be written.
Signed-off-by: NNikolaus Voss <n.voss@weinmann.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some DS13XX devices have "trickle chargers".  Its configuration register
is at different locations, the setup is the same, though.  Since the
configuration is board specific, introduce a platform_data to this driver.
Tested with a DS1339 on a custom board.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ds1307 was kzalloced, so no need to zero members of the struct.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In order to keep consistency with other rtc drivers,rename CONFIG_RTC_MXC
to CONFIG_RTC_DRV_MXC.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
[akpm@linux-foundation.org: fix missed arch/arm/configs/imx_v6_v7_defconfig]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

RTC_DRV_IMXDI and RTC_MXC are on-chip RTC modules, so move them under
"on-CPU RTC drivers" selection menu.

While at it change the dependency of RTC_DRV_IMXDI from ARCH_MX25 to
SOC_IMX25.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Changes are based on arch/cris/arch-v10/drivers/pcf8563.c

[akpm@linux-foundation.org: fix sparse warning]
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mikael Starvik <starvik@axis.com>
Acked-by: NJesper Nilsson <jesper.nilsson@axis.com>
Cc: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently there is no generic way to get the RTC battery status within an
application.  So add an ioctl to read the status bit.  The idea is that
the bit is set once a low voltage is detected.  It stays there until it is
reset using the RTC_VL_CLR ioctl.
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use module_platform_driver() to remove the boilerplate code.

Also, change the probe and remove functions to __devinit/__devexit.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SPEAr platforms now support DT and so must convert all drivers support DT.
This patch adds DT probing support for rtc and updates its documentation
too.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Cc: Rob Herring <robherring2@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

number()'s behaviour is slighly changed: 0 becomes "0" instead of "00"
when using the flag SPECIAL and base 8.

Before:
Number\Format  %o    %#o  %x    %#x
            0     0   00    0   0x0
            1     1   01    1   0x1
           16    20  020   10  0x10

After:
Number\Format  %o    %#o  %x    %#x
            0     0    0    0   0x0
            1     1   01    1   0x1
           16    20  020   10  0x10
Signed-off-by: NPierre Carrier <pierre@spotify.com>
Acked-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We are not preallocating a sufficient number of nodes.
Signed-off-by: NNick Piggin <npiggin@kernel.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a spinlock warning is printed we usually get

 BUG: spinlock bad magic on CPU#0, modprobe/111
  lock: 0xdff09f38, .magic: 00000000, .owner: /0, .owner_cpu: 0

but it's nicer to print the symbol for the lock if we have it so that we
can avoid 'grep dff09f38 /proc/kallsyms' to find out which lock it was.
Use kallsyms to print the symbol name so we get something a bit easier to
read

 BUG: spinlock bad magic on CPU#0, modprobe/112
  lock: test_lock, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0

If the lock is not in kallsyms %ps will fall back to printing the address
directly.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Using %ps in a printk format will sometimes fail silently and print the
empty string if the address passed in does not match a symbol that
kallsyms knows about.  But using %pS will fall back to printing the full
address if kallsyms can't find the symbol.  Make %ps act the same as %pS
by falling back to printing the address.

While we're here also make %ps print the module that a symbol comes from
so that it matches what %pS already does.  Take this simple function for
example (in a module):

	static void test_printk(void)
	{
		int test;
		pr_info("with pS: %pS\n", &test);
		pr_info("with ps: %ps\n", &test);
	}

Before this patch:

 with pS: 0xdff7df44
 with ps:

After this patch:

 with pS: 0xdff7df44
 with ps: 0xdff7df44
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The code comments for bscnl_emit() and bitmap_scnlistprintf() are
describing snprintf() return semantics, but these functions use
scnprintf() return semantics.  Fix that, and document the
bitmap_scnprintf() return value as well.

Cc: Ryota Ozaki <ozaki.ryota@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>