Touchpad LED will not turn on after S3, it will make the touchpad status
doesn't consist with the LED.
By adding one flag to let the LED device restore it's status.
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Trivial platform driver for Traverse Technologies Geos and Geos2
single-board computers. Uses SMBIOS to identify platform.
Based on progressive revisions of the leds-net5501 driver that
was rewritten by Ed Wildgoose as a platform driver.

Supports GPIO-based LEDs (3) and 1 polled button which is
typically used for a soft reset.
Signed-off-by: NPhilip Prindeville <philipp@redfish-solutions.com>
Reviewed-by: NEd Wildgoose <ed@wildgooses.com>
Acked-by: NAndres Salomon <dilinger@queued.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

This doesn't change how the code works, but it silences a Sparse
complaint:
drivers/platform/x86/toshiba_acpi.c:121:37: error: dubious one-bit signed bitfield
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

The "wmi_interface *iface" is a useless input argument for internal wmi get/set
functions, remove it to clear up source code.

Tested on Lenovo E520.
Tested on Acer TravelMate 4750.
Tested-by: Nmr.kobzar <mr.kobzar@gmail.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: NLee, Chun-Yi <jlee@suse.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

This will let the MSIC driver to create platform device for the thermal
driver.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Instead of complaining that the voltage is on, we can just ask the MSIC to
turn the voltage off. This should save some power.

Voltage for thermistors is turned on when ADC conversion is initiated.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Intel MSIC MFD driver provides common register access interface to the
devices in the MSIC die so we use that instead of SCU IPC.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

In newer boards this device is called "msic_thermal" instead of
"msic_sensor". To support both we add suitable alias for the driver.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Signed-off-by: NCorentin Chary <corentin.chary@gmail.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

asus_acpi only support old models, it has been deprecated since
2009 in favor of asus-laptop, it's not built by any (sane) distro,
so it is time to say good bye.

Thanks to Julien Lerouge and Karol Kozimor for the work they have
done on it, I would never have wrote asus-laptop and other asus
related drivers without asus_acpi.
Signed-off-by: NCorentin Chary <corentin.chary@gmail.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Signed-off-by: NCorentin Chary <corentin.chary@gmail.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

But don't try to do than on pegatron tablets to avoid any
conflict.
Signed-off-by: NCorentin Chary <corentin.chary@gmail.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Let the user tells if BLED and WLED should be exposed as led or
rfkill (the old sysfs are still here, but this adds a standard
interface to control the device).

For example on my A6JC, with WAPF=1, I would do:

$ modprobe asus-laptop wled_type=led bluetooth_type=rfkill

There is still no known way to automatically guess what BLED
and WLED methods will control, it's why user information is needed.

A userspace database could do that automatically, and maybe some DMI
matching in the driver.
Signed-off-by: NCorentin Chary <corentin.chary@gmail.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Signed-off-by: NCorentin Chary <corentin.chary@gmail.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Signed-off-by: NCorentin Chary <corentin.chary@gmail.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Use pr_warn not pr_warning.
Coalesce formats.
Argument aligning.
Remove superfluous parentheses.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLee, Chun-Yi <jlee@suse.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Use pr_warn not pr_warning.
Coalesce formats.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLee, Chun-Yi <jlee@suse.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

- don't output error when probing features at load
- print the SABI signature if samsung_sabi_init()
  succeed
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

We still need to figure out exactly what each of different fields
represent, but they contain at least model and version informations.
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

This enable the driver for everything that look like
a laptop and is from vendor "SAMSUNG ELECTRONICS CO., LTD.".
Note that laptop supported by samsung-q10 seem to have a different
vendor strict.

Also remove every log output until we know that we have a SABI interface
(except if the driver is forced to load, or debug is enabled).

Keeping a whitelist of laptop with a model granularity is something that can't
work without close vendor cooperation (and we don't have that).
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

The wireless status get and get commands seems to use one
byte per device. First byte is for wlan and third is for bluetooh,
we will have to find what the other are for.
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

We can now do the self test using debugfs, so remove the code
and keep the debug flag to enable more traces.
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

This allow to call arbitrary sabi commands wihout
modifying the driver at all. For example, setting
the keyboard backlight brightness to 5 using debugfs
interface can be done like that:

 ; Set the command
 echo 0x78 > command
 ; Set the data
 echo 0x0582 > d0
 ; Fill the rest with 0
 echo 0 > d1
 echo 0 > d2
 echo 0 > d3
 ; And issue the command
 cat call
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

* SABI command are on 16 bits, not 8
* SABI can read/write up to 11 byte of data
* There is not real difference between "get" and "set"
  commands, so refactorise the code of both functions
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Will be usefull later when we will have more platform sysfs files
like battery_life_extender or usb_charge.
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

samsung-laptop is not at all related to ACPI, but since this interface
is not documented at all, and the driver has to use it at load to
understand how it works on the laptop, I think it's a good idea to
disable it if a better solution is available.
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Create _init()/_exit() function for each subsystem, remove
the local struct samsung_laptop * and only keep a
struct platform_device * that can only be used in samsung_init()
and samsung_exit().
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Even if this driver can only be loaded once, it is still a good
idea to create some kind of context structure.
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

This patch converts the drivers in drivers/platform/x86/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: Hong Liu <hong.liu@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Turn off the following triggered with gcc 4.6.1 on Debian testing:

drivers/platform/x86/hdaps.c: In function ‘hdaps_temp2_show’:
drivers/platform/x86/hdaps.c:398:16: warning: ‘temp’ may be used uninitialized in this function [-Wuninitialized]
drivers/platform/x86/hdaps.c: In function ‘hdaps_temp1_show’:
drivers/platform/x86/hdaps.c:385:16: warning: ‘temp’ may be used uninitialized in this function [-Wuninitialized]

Cc: Frank Seidel <frank@f-seidel.de>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: NBorislav Petkov <bp@alien8.de>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Add "Vostro 3555", "Inspiron N311z", and "Inspiron M5110" into quirks,
so that they could have touchpad LED function work.
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Fix scancodes returned by driver to match scancodes used to remap keys.

(Before the patch FN/E returned scancode 0x1B, but to remap scancode
0x14 had to be used).

The scancodes returned by the sony-laptop driver for function keys did not
match the scancodes used to remap keys.  Also, since the scancode was sent
to the input subsystem after the mapped keysym the /lib/udev/keymap
utility was confused about which scancode to report for which keysym.

This patch fixes the driver so the correct scancode is shown for each
key.  It also adds to the documentation a description of where to find
the scancodes.
Signed-off-by: NJohn Hughes <john@calva.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

All the production devices use the PC compatible version of this device so
don't use the SCU interfaces or the SCU firmware interfaces.

Delete lots of code and conditional paths
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>