Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Check whether L2 is present or not in XSC3. If it's present, enable L2
immediately.

Disabling L2 after L2 is enabled that would result in unpredicatable behavior
of XSC3 processor.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Outer cache checked whether L2 is enabled or not. If L2 isn't enabled in XSC3,
it would enable L2. This operation is evil that would make system hang.

In XSC3 core document, these words are mentioned in below.

"Following reset, the L2 Unified Cache Enable bit is cleared. To enable the L2
Cache, software may set the bit to a '1' before or at the same time as enabling
the MMU. Enabling the L2 Cache after the MMU has been enabled or disabling the
L2 Cache after the L2 Cache has been enabled, may result in unpredictable
behavior of the processor."

When outer cache is initialized, the MMU is already enabled. We couldn't enable
L2 after MMU enabled.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

PXA mmc host driver supports card detect, read only and power gpio pin
setting already. Zylonite platform driver needn't implement this any more.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

ARRAY_AND_SIZE is already defined arch/arm/mach-mmp/common.h which is
already included.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Bin Yang <bin.yang@marvell.com>
Acked-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarc Zyngier <maz@misterjones.org>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

DM9000s on Zeus sometime fail under heavy load.
Relaxing the timings a bit seems to be of a great help.
Signed-off-by: NMarc Zyngier <maz@misterjones.org>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarc Zyngier <maz@misterjones.org>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This has to be selected, otherwise some peripherals don't get initialized.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Use resource_size for {request/release}_mem_region and ioremap.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

We can't request the cascade channel before it's been registered, so
move it afterwards.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This fixes a "start_kernel(): bug: interrupts were enabled early".

rtc_cmos now takes care of initializing the ISA RTC and reading the
current time and date from it; there's no need to repeat that here,
thereby causing interrupts to be enabled too early.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

PAGE_KERNEL should not be executable; any area marked executable can
be prefetched into the instruction cache.  We don't want vmalloc areas
to be read in this way.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

It is unpredictable to have the same memory mapped using different
shared bit settings for ARMv6 and ARMv7 CPUs.  Fix this for the CPU
write buffer bug test.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit f74f7e57 (ARM: use
flush_kernel_dcache_area() for dmabounce) has broken dmabounce build:

  CC      arch/arm/common/dmabounce.o
arch/arm/common/dmabounce.c: In function 'unmap_single':
arch/arm/common/dmabounce.c:315: error: implicit declaration of function '__cpuc_flush_kernel_dcache_area'
make[2]: *** [arch/arm/common/dmabounce.o] Error 1

Fix it.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix bug of uart0 platfrom data for nuc900
Signed-off-by: Nlijie <eltshanli@gmail.com>
Signed-off-by: NWan ZongShun <mcuos.com@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

putc support for nuc900
Signed-off-by: Nlijie <eltshanli@gmail.com>
Signed-off-by: NWan ZongShun <mcuos.com@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

fix compiling error for NUC900
Signed-off-by: Nlijie <eltshanli@gmail.com>
Signed-off-by: NWan ZongShun <mcuos.com@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On Oprofile ARMv7 the PMNC_D bit was set to lower the PMU IRQs
and so to decrease the risk of errata #628216 from appearing.
The effect of setting the PMNC_D bit is that the CCNT counter
is divided by 64, making the program counter events count
inaccurate.
The new OMAP3 r4 cores should have that errata fixed.

The PMNC_D bit should not be set, this patch fixes it.
Signed-off-by: NJean Pihet <jpihet@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

26-bit ARM support was removed a long time ago, and this symbol has
been defined to be 'y' ever since.  As it's never disabled anymore,
we can kill it without any side effects.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This avoids races in the VFP code where the dead thread may have
state on another CPU.  By moving this code to exit_thread(), we
will be running as the thread, and therefore be running on the
current CPU.

This means that we can ensure that the only local state is accessed
in the thread notifiers.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 2c9b9c84 added an argument to __cpuc_flush_dcache_page
and renamed it.

Update a caller of the old function to fix this build error:

  CC      arch/arm/mm/copypage-v6.o
arch/arm/mm/copypage-v6.c: In function 'v6_copy_user_highpage_nonaliasing':
arch/arm/mm/copypage-v6.c:51: error: implicit declaration of function '__cpuc_flush_dcache_page'
make[1]: *** [arch/arm/mm/copypage-v6.o] Error 1
make: *** [arch/arm/mm] Error 2
Reported-by: NJinsung Yang <jsgood.yang@samsung.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add pseudo-DMA by FIQ to the S3C24XX SPI driver.  This allows the driver
to get DMA-like performance where there are either no free DMA channels or
when doing transfers that required both TX and RX data paths.

Since this patch requires the addition of an assembly file to hold the FIQ
code, we rename the module (instead of adding a rename of the .c file to
this patch).  We expect most users are loading this via udev and thus
there should be no change to the userland configuration.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NSimtec Linux Team <linux@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Commit f62349ee had side effect that
causes kernel to oops when we are suspending to ram:

	# echo mem > /sys/power/state

	WARNING: at kernel/irq/manage.c:858 __free_irq+0x90/0x174()
	Trying to free already-free IRQ 72
	Modules linked in:
	Backtrace:
	[<c00328d0>] (dump_backtrace+0x0/0x110) from [<c0347298>] (dump_stack+0x18/0x1c)
	 r7:dfd4be08 r6:c009505c r5:c03fbfd1 r4:0000035a
	[<c0347280>] (dump_stack+0x0/0x1c) from [<c005a408>] (warn_slowpath_common+0x50/0x68)
	[<c005a3b8>] (warn_slowpath_common+0x0/0x68) from [<c005a46c>] (warn_slowpath_fmt+0x30)
	 r7:c0474afc r6:00000048 r5:00000000 r4:c0474ac0
	[<c005a43c>] (warn_slowpath_fmt+0x0/0x38) from [<c009505c>] (__free_irq+0x90/0x174)
	 r3:00000048 r2:c03fc0ef
	[<c0094fcc>] (__free_irq+0x0/0x174) from [<c0095184>] (free_irq+0x44/0x64)
	[<c0095140>] (free_irq+0x0/0x64) from [<c0038100>] (omap_uart_enable_irqs+0x4c/0x90)
	 r7:c034d58c r6:00000003 r5:00000000 r4:c0463028
	[<c00380b4>] (omap_uart_enable_irqs+0x0/0x90) from [<c003d8f8>] (omap3_pm_begin+0x1c/0)
	 r5:00000003 r4:00000000
	[<c003d8dc>] (omap3_pm_begin+0x0/0x28) from [<c008d008>] (suspend_devices_and_enter+0x)
	[<c008cfd8>] (suspend_devices_and_enter+0x0/0x1dc) from [<c008d29c>] (enter_state+0xe8)
	 r5:c03f7f46 r4:00000000
	[<c008d1b4>] (enter_state+0x0/0x140) from [<c008c8e0>] (state_store+0x9c/0xc4)
	 r7:c034d58c r6:00000003 r5:00000003 r4:c03f7f46
	[<c008c844>] (state_store+0x0/0xc4) from [<c01cb2dc>] (kobj_attr_store+0x20/0x24)
	[<c01cb2bc>] (kobj_attr_store+0x0/0x24) from [<c0119420>] (sysfs_write_file+0x114/0x14)
	[<c011930c>] (sysfs_write_file+0x0/0x148) from [<c00cb298>] (vfs_write+0xb8/0x164)
	[<c00cb1e0>] (vfs_write+0x0/0x164) from [<c00cb408>] (sys_write+0x44/0x70)
	 r8:4001f000 r7:00000004 r6:df81bd00 r5:00000000 r4:00000000
	[<c00cb3c4>] (sys_write+0x0/0x70) from [<c002f040>] (ret_fast_syscall+0x0/0x38)
	 r8:c002f204 r7:00000004 r6:401fa5e8 r5:4001f000 r4:00000004

This is due the fact that uart_list list was populated in
omap_serial_early_init() and omap_uart_enable_irqs() went through this
list even when serial idle wasn't enabled for all uarts.

This patch moves the code that populates the uart_list and enables uart
clocks into omap_serial_init_port().
Signed-off-by: NMika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Recent drivers/mfd/twl4030* renames to twl broke compile for
various boards as the series was missing a patch to change
the board-*.c files.

This patch renames include twl4030.h to include twl.h
and also renames twl4030_i2c_ routines.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Currently all architectures but microblaze unconditionally define
USE_ELF_CORE_DUMP.  The microblaze omission seems like an error to me, so
let's kill this ifdef and make sure we are the same everywhere.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: <linux-arch@vger.kernel.org>
Cc: Michal Simek <michal.simek@petalogix.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add the platform specific callback to control LCD panel and backlight
power.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Commit db205463 was incorrectly applied,
and reverted here to re-apply.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

OMAP34XX has EHCI, so select USB_ARCH_HAS_EHCI.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This driver was merged before the ep93xx core support was added
for the keypad clock and acquiring/releasing the necessary gpio's.
Now that the proper support is in the ep93xx core this driver
needs to be updated to work correctly.

Summary of changes:
  1) Remove some unused members from the platform data.
  2) Remove the custom KEY macro and use the ones available in
     <linux/input/matrix_keypad.h>
  3) Remove the keypad_{readl/writel} macros and just use
     __raw_{readl/writel} directly.
  4) Update the clk_set_rate() call to work with the core support.
  5) Cleanup the probe routine and remove some unneeded messages.
  6) Use the ep93xx core functions to acquire and release the gpio's.
  7) Fix the clk_get() call to get the keypad clock.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Allow the use of another DMA controller driver in atmel-mci sd/mmc driver.
 This adds a generic dma_slave pointer to the mci platform structure where
we can store DMA controller information.  In atmel-mci we use information
provided by this structure to initialize the driver (with new helper
functions that are architecture dependant).

This also adds at32/avr32 chip modifications to cope with this new access
method.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The Kconfigs for in-tree floating point emulation do not allow building
as modules. That leaves the Acorn FPEmulator module. I found two public
releases of this as a binary module for 2.1 and 2.2 kernels, optimized
for ARMV4.[1] If there is a resurgence of interest in this, the symbols
can always be re-exported.

This allows the EXPORT_SYMBOL_ALIAS() hack to be removed. The ulterior
motive here is that EXPORT_SYMBOL_ALIAS() makes it harder to sort the
resulting kernel symbol tables.  Sorted symbol tables will allow faster
symbol resolution during module loading.

Note that fp_send_sigs() and fp_printk() are simply aliases for existing
exports and add no obvious value.  Similarly fp_enter could easily be
renamed to kern_fp_enter at the point of definition. Therefore removing
EXPORT_SYMBOL_ALIAS will not serve as a material obstacle to re-adding
the exports should they be desired in future.

Build tested only.

[1] http://ftp.arm.linux.org.uk/pub/linux/arm/fpemulator/Signed-off-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Commit 023bf6f1 "linker script: unify usage of discard definition"
changed the linker scripts for all architectures except for ARM.
I can find no discussion about this ommision, so here are the changes
for ARM.

These changes are exactly parallel to the ia64 case.

"ia64 is notable because it first throws away some ia64 specific
 subsections and then include the rest of the sections into the final
 image, so those sections must be discarded before the inclusion."

Not boot-tested.  In build testing, the modified linker script generated
an identical vmlinux file.

[I would like to be able to rely on this unified discard definition.
 I want to sort the kernel symbol tables to allow faster symbol
 resolution during module loading. The simplest way appears to be
 to generate sorted versions from vmlinux.o, link them in to vmlinux,
 _and discard the original unsorted tables_.

 This work is driven by my x86 netbook, but it is implemented at a
 generic level. It is possible it will benefit some ARM systems also.]
Signed-off-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by-without-testing: Tejun Heo <tj@kernel.org>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPeter Zijlstra <peterz@infradead.org>
Acked-by: NIngo Molnar <mingo@elte.hu>