This allows to monitor carrier on/off transitions and detect link
flapping issues:
 - new /sys/class/net/X/carrier_changes
 - new rtnetlink IFLA_CARRIER_CHANGES (getlink)

Tested:
  - grep . /sys/class/net/*/carrier_changes
    + ip link set dev X down/up
    + plug/unplug cable
  - updated iproute2: prints IFLA_CARRIER_CHANGES
  - iproute2 20121211-2 (debian): unchanged behavior
Signed-off-by: NDavid Decotigny <decot@googlers.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is in net-next only, for couple of days. Not used anymore, and never
should have been. So just remove it and pretend it was never there.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent patch
bonding: add netlink attributes to slave link dev (1d3ee88a)

Introduced yet another device specific way to access slave information
over rtnetlink. There is one already there for bridge.

This patch introduces generic way to do this, for getting and setting
info as well by extending link_ops. Later on, this new interface will
be used for bridge ports as well.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If link is IFF_SLAVE, extend link dev netlink attributes to include
slave attributes with new IFLA_SLAVE nest.  Add netlink notification
(RTM_NEWLINK) when slave status changes from backup to active, or
visa-versa.

Adds new ndo_get_slave op to net_device_ops to fill skb with IFLA_SLAVE
attributes.  Currently only used by bonding driver, but could be
used by other aggregating devices with slaves.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add nested IFLA_BOND_AD_INFO for bonding 802.3ad info.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_AD_SELECT to allow get/set of bonding parameter
ad_select via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_AD_LACP_RATE to allow get/set of bonding parameter
lacp_rate via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_PACKETS_PER_SLAVE to allow get/set of bonding parameter
packets_per_slave via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_LP_INTERVAL to allow get/set of bonding parameter
lp_interval via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_MIN_LINKS to allow get/set of bonding parameter
min_links via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_ALL_SLAVES_ACTIVE to allow get/set of bonding parameter
all_slaves_active via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_NUM_PEER_NOTIF to allow get/set of bonding parameter
num_grat_arp via netlink.  Bonding parameter num_unsol_na is
synonymous with num_grat_arp, so add only one netlink attribute
to represent both bonding parameters.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_RESEND_IGMP to allow get/set of bonding parameter
resend_igmp via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_XMIT_HASH_POLICY to allow get/set of bonding parameter
xmit_hash_policy via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_FAIL_OVER_MAC to allow get/set of bonding parameter
fail_over_mac via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_PRIMARY_SELECT to allow get/set of bonding parameter
primary_select via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_PRIMARY to allow get/set of bonding parameter
primary via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_ARP_ALL_TARGETS to allow get/set of bonding parameter
arp_all_targets via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_ARP_VALIDATE to allow get/set of bonding parameter
arp_validate via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_ARP_IP_TARGET to allow get/set of bonding parameter
arp_ip_target via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_ARP_INTERVAL to allow get/set of bonding parameter
arp_interval via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_USE_CARRIER to allow get/set of bonding parameter
use_carrier via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_DOWNDELAY to allow get/set of bonding parameter
downdelay via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_UPDELAY to allow get/set of bonding parameter
updelay via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BOND_MIIMON to allow get/set of bonding parameter
miimon via netlink.
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This implements the rtnl_link_ops fill_info routine for HSR.
Signed-off-by: NArvid Brodin <arvid.brodin@alten.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

High-availability Seamless Redundancy ("HSR") provides instant failover
redundancy for Ethernet networks. It requires a special network topology where
all nodes are connected in a ring (each node having two physical network
interfaces). It is suited for applications that demand high availability and
very short reaction time.

HSR acts on the Ethernet layer, using a registered Ethernet protocol type to
send special HSR frames in both directions over the ring. The driver creates
virtual network interfaces that can be used just like any ordinary Linux
network interface, for IP/TCP/UDP traffic etc. All nodes in the network ring
must be HSR capable.

This code is a "best effort" to comply with the HSR standard as described in
IEC 62439-3:2010 (HSRv0).
Signed-off-by: NArvid Brodin <arvid.brodin@xdin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds IPv6 support to vxlan device, as the new version
RFC already mentions it:

   http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-03

Cc: David Stevens <dlstevens@us.ibm.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NNarendra K <narendra_k@dell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add netlink directives and ndo entry to allow for controling
VF link, which can be in one of three states:

Auto - VF link state reflects the PF link state (default)

Up - VF link state is up, traffic from VF to VF works even if
the actual PF link is down

Down - VF link state is down, no traffic from/to this VF, can be of
use while configuring the VF
Signed-off-by: NRony Efraim <ronye@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a flag to control flood of unicast traffic.  By default, flood is
on and the bridge will flood unicast traffic if it doesn't know
the destination.  When the flag is turned off, unicast traffic
without an FDB will not be forwarded to the specified port.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow user to control whether mac learning is enabled on the port.
By default, mac learning is enabled.  Disabling mac learning will
cause new dynamic FDB entries to not be created for a particular port.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow configuring the default destination port on a per-device basis.
Adds new netlink paramater IFLA_VXLAN_PORT to allow setting destination
port when creating new vxlan.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Source compatiability for build iproute2 was broken by:
  commit c7995c43
  Author: Atzm Watanabe <atzm@stratosphere.co.jp>
    vxlan: Allow setting destination to unicast address.

Since this commit has not made it upstream (still net-next),
and better to avoid gratitious changes to exported API's;
go back to original definition, and add a comment.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for 802.1ad VLAN devices. This mainly consists of checking for
ETH_P_8021AD in addition to ETH_P_8021Q in a couple of places and check
offloading capabilities based on the used protocol.

Configuration is done using "ip link":

# ip link add link eth0 eth0.1000 \
	type vlan proto 802.1ad id 1000
# ip link add link eth0.1000 eth0.1000.1000 \
	type vlan proto 802.1q id 1000

52:54:00:12:34:56 > 92:b1:54:28:e4:8c, ethertype 802.1Q (0x8100), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84)
    20.1.0.2 > 20.1.0.1: ICMP echo request, id 3003, seq 8, length 64
92:b1:54:28:e4:8c > 52:54:00:12:34:56, ethertype 802.1Q-QinQ (0x88a8), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 47944, offset 0, flags [none], proto ICMP (1), length 84)
    20.1.0.1 > 20.1.0.2: ICMP echo reply, id 3003, seq 8, length 64
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows setting VXLAN destination to unicast address.
It allows that VXLAN can be used as peer-to-peer tunnel without
multicast.

v4: generalize struct vxlan_dev, "gaddr" is replaced with vxlan_rdst.
    "GROUP" attribute is replaced with "REMOTE".
    they are based by David Stevens's comments.

v3: move a new attribute REMOTE into the last of an enum list
    based by Stephen Hemminger's comments.

v2: use a new attribute REMOTE instead of GROUP based by
    Cong Wang's comments.
Signed-off-by: NAtzm Watanabe <atzm@stratosphere.co.jp>
Acked-by: NDavid L Stevens <dlstevens@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>