Add support for eMMC/SD/SDIO Intel GLK host controllers.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The newer msm sdhci's cores use a different DLL hardware for HS400.
Update the configuration and calibration of the newer DLL block.

The HS400 DLL block used previously is CDC LP 533 and requires
programming multiple registers and waiting for configuration to
complete and then enable it. It has about 18 register writes and
two register reads.

The newer HS400 DLL block is SDC4 DLL and requires two register
writes for configuration and one register read to confirm that it
is initialized. There is an additional register write to enable
the power save mode for SDC4 DLL block.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Signed-off-by: NKrishna Konda <kkonda@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In HS400 mode a new RCLK is introduced on the interface for read data
transfers. The eMMC5.0 device transmits the read data to the host with
respect to rising and falling edges of RCLK. In order to ensure correct
operation of read data transfers in HS400 mode, the incoming RX data
needs to be sampled by delayed version of RCLK.

The CDCLP533 delay circuit shifts the RCLK by T/4. It needs to be
initialized, configured and enabled once during HS400 mode switch and
when operational voltage/clock is changed.
Signed-off-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Save the tuning phase once the tuning is performed.
This phase value will be used while calibrating DLL
for HS400 mode.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The following msm platform specific changes are added to support HS400.
- Allow tuning for HS400 mode.
- Configure HS400 timing mode using the VENDOR_SPECIFIC_FUNC register.
Signed-off-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

SDHC MSM controller need 2x clock for MCLK at GCC.
Hence make required changes to have 2x clock for
DDR timing modes.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

sdhci-msm controller may have different clk-rates for each
bus speed mode. Thus implement set_clock callback for
sdhci-msm driver.
Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Factor out sdhci_enable_clk from sdhci_set_clock
and make it EXPORT_SYMBOL so that it can be called.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

sdhc-msm controller needs this SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN
& SDHCI_QUIRK2_PRESET_VALUE_BROKEN to be set. Hence setting it.
Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This add get_min_clock() and get_max_clock() callback
for sdhci-msm. sdhci-msm min/max clocks may be different
hence implement these callbacks.
Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

SDCC core with minor version >= 0x42 introduced new 14lpp
DLL. This has additional requirements in the reset sequence
for DLL tuning. Make necessary changes as needed.

Without this patch we see below errors on such SDHC controllers
	sdhci_msm 7464900.sdhci: mmc0: DLL failed to LOCK
	mmc0: tuning execution failed: -110
Signed-off-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add "xo" value which is tcxo clock to sdhci-msm
DT binding properties.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch changes the poor style of writel/readl registers
into more readable format. This avoid mixed style format
of readl/writel in sdhci-msm driver.
This patch also removes the one line comments which were present for
above writel/readl, since they were of no help.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

"support-highspeed" was the obsoleted property.
And "broken-cd" is not synopsys specific property.
It can be referred to mmc.txt binding Documentation.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The "clock-freq-min-max" property was deprecated.
There is "max-frequency" property in drivers/mmc/core/host.c
"max-frequency" can be replaced with "clock-freq-min-max".
Minimum clock value might be set to 100K by default.
Then MMC core should try to find the correct value from 400K to 100K.
So it just needs to set Maximum clock value.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove the unnecessary mmc_data structure.
Instead, cmd->data can be used.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch removed the meaningless value. Instead, use the cookie's enum
values for executing correctly.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

stop_cmdr should be set to values relevant to stop command.
It migth be assigned to values whatever there is mrq->stop or not.
Then it doesn't need to use dw_mci_prepare_command().
It's enough to use the prep_stop_abort for preparing stop command.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If DW_MMC_CARD_NO_USE_HOLD isn't set, it's usesd by default.
Enve if SDMMC_CMD_USB_HOLD_REG is set in prepare_command(), but it
doesn't set in pre_stop_abort().

To maintain the consistency, add the checking condition for this.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If there is no property "clock-freq-min-max", mmc->f_min should be set
to 400K by default. But Some SoC can be used 100K.
When 100K is used, MMC core will try to check from 400K to 100K.
Reported-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If display the debug message, this message should be spamming.
If flags is maintained the previous value, didn't display the debug
message.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Developer wants to see the real register value, not register offset.
This patch fixed to display the real value of register.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Trivial fix to spelling mistake "desciptor" to "descriptor" in
dev_dbg message.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

By moving the mmc_packed_init() and mmc_packed_clean() into the
only file in the kernel where they are used, we save two exported
functions and can staticize those to the block.c file.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The struct mmc_blk_request contains an opaque void *data that
is actually only used to store a pointer to a per-request
struct mmc_blk_data. This is confusing, so rename the member
to blkdata and forward-declare the block.c local struct.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Instead of open coding the check for the same thing that
the helper checks: use the helper.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Request card detect and write protect gpios using the provided API
by mmc core.

If a gpio is provided for card detect, we don't need to poll.
So only use polling when a gpio is not provided.

Once all pdata users register the gpios using gpio descriptors,
we could remove the platform callbacks.
Signed-off-by: NAxel Haslam <ahaslam@baylibre.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NDavid Lechner <david@lechnology.com>

Card detect and write protect are currently not working on a DT
boot, and the driver relies on polling to get the state
of the card. The current code depends on platform data callbacks
to register and get the state of the gpios.

mmc core provides a generic way to parse device tree configuration,
which will take care of registering the gpios for us, lets use it
so that we don't need to poll, and parse the same properties.
Signed-off-by: NAxel Haslam <ahaslam@baylibre.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NDavid Lechner <david@lechnology.com>

We surely have SDIO support by now :)
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Commit 7729c7a2 ("mmc: tmio: Provide separate interrupt handlers")
refactored the sdio irq handler and wrongly used the mask for SD irqs,
not for SDIO irqs. This doesn't really matter in practice because both
values keep the only interrupt we are interested in. But still, this is
wrong and wants to be fixed.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

wbsd_request_dma() does not check for dma mapping errors.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We never set "ret" to RESULT_OK.

Fixes: 9f9c4180 ("mmc: mmc_test: add test for non-blocking transfers")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The type of host->private is (unsigned long *).  No cast is needed
to return an opaque pointer.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add bytewise register accesses support for newer versions of IPROC
SDHCI controllers.
Previous sdhci-iproc versions of SDIO controllers
(such as Raspberry Pi and Cygnus) only allowed for 32-bit register
accesses.
Signed-off-by: NSrinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: NScott Branden <scott.branden@broadcom.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Adds brcm,sdhci-iproc compat string to DT bindings document for
the iProc SDHCI driver.
Signed-off-by: NAnup Patel <anup.patel@broadcom.com>
Signed-off-by: NScott Branden <scott.branden@broadcom.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add tuning support for use with SDR104 mode
This includes adding support for the sampling clock controller (SCC).

Based on work by Ai Kyuse.

Cc: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add tuning support for use with SDR104 mode
Signed-off-by: NAi Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add hw reset support.
Signed-off-by: NAi Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

An illegal sequence command error may occur if there is a stopbit or
cmd_index error as well as a CRC error. The correct course of action
is to re-enable IRQs

An illegal sequence data error may occur if there is a CRC or stopbit
error,  or underrun. In this case set data->error correctly.

This is in preparation for enabling tuning support which relies on
differentiating between illegal sequence and other errors.
Signed-off-by: NAi Kyuse <ai.kyuse.uw@renesas.com>
[simon: broken out of a larger patch]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>