- 07 8月, 2009 3 次提交
-
-
由 Sascha Hauer 提交于
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
由 Sascha Hauer 提交于
Everyone should be free to include the files he actually needs. Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
由 Sascha Hauer 提交于
Use the default value of 256 which is enough for all i.MX SoCs. Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
- 18 5月, 2009 1 次提交
-
-
由 Magnus Lilja 提交于
The i.MX31 PDK consists of several boards, one of them is a debug board containing a CPLD which controls some debug leds, switch buttons, an interrupt chip and an Ethernet controller. This patch adds support for detecting if the PDK board is present (during boot) and adds the interrupt chip to the kernel. Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com> Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
- 13 3月, 2009 2 次提交
-
-
由 Sascha Hauer 提交于
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
由 Sascha Hauer 提交于
This patch moves the stuff common to i.MX31 and i.MX35 to mx3x.h and the specifics to mx31.h/mx35.h. We can build a kernel which runs on i.MX31 and i.MX35, so always include mx31.h and mx35.h Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
- 18 12月, 2008 3 次提交
-
-
由 Sascha Hauer 提交于
Instead of including other header files, define PHYS_OFFSET directly Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
由 Sascha Hauer 提交于
Instead of including other header files, define CLOCK_TICK_RATE directly Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
由 Sascha Hauer 提交于
This patch removes the inclusion of mach/hardware.h from mach/irqs.h and switches to more meaningful names for the irq related macros. Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
- 09 9月, 2008 1 次提交
-
-
由 Luotao Fu 提交于
Fix some base address declaration by adding a cast. Signed-off-by: NLuotao Fu <l.fu@pengutronix.de> Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
- 07 8月, 2008 1 次提交
-
-
由 Russell King 提交于
This just leaves include/asm-arm/plat-* to deal with. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 05 7月, 2008 2 次提交
-
-
由 Juergen Beisert 提交于
Simplify architecture's irq headers and sources, to share these files between MXC3 and MXC2. Signed-off-by: NJuergen Beisert <j.beisert@pengutronix.de>
-
由 Juergen Beisert 提交于
This patch bases on the one from Daniel Mack. The most important change to Daniel's patch is to be more generic. This gpio routine supports at least the i.MX27 and i.MX31 processors. Signed-off-by: NJuergen Beisert <j.beisert@pengutronix.de> Acked-by: NDaniel Mack <daniel@caiaq.de>
-
- 17 4月, 2008 1 次提交
-
-
由 Robert Schwebel 提交于
From: Juergen Beisert <j.beisert@pengutronix.de> This patch separates the current code into i.MX2 and i.MX3 and modifies the Kconfig files to reflect this separation in the menus. Things happend since last review: - make i.MX3 compile again - fix some structure names to be conform with all the shared/common sources from i.MX1/i.MX2 Previous changes: - stay conform to other Kconfig files (note from Russell King) Signed-off-by: NJuergen Beisert <j.beisert@pengutronix.de> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 22 7月, 2007 1 次提交
-
-
由 Quinn Jensen 提交于
This patch adds the foundation pieces for the Freescale MXC platforms, including i.MX2 and i.MX3 based systems. The bare-bones MX31 support in this patch boots to the rootdev panic with 8250 serial console configured "console=ttyS0,115200". It assumes that Redboot is the boot loader. Signed-off-by: NQuinn Jensen <quinn.jensen@freescale.com> Acked-by: NLennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-