Y2_HW_WOL_ON/Y2_HW_WOL_OFF should be set and cleared per chip,
not per port.  On dual port cards, Y2_HW_WOL_ON should be
enabled if either sky2 port has WOL enabled.

Found while reviewing code for a WOL regression, though this is
probably not the cause of the regression.
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Found this problem when testing IPv6 from a KVM guest to a remote
host via e1000e device on the host.
The following patch fixes the check for IPv6 GSO packet in Intel
ethernet drivers to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.
Signed-off-by: NSridhar Samudrala <sri@us.ibm.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After removing the skb_dma_map/unmap calls the exception handling in
igb_tx_map_adv is not correct.  The issue is that the count value was not
being correctly handled so as a result we were not rewinding the ring as
back as we should have been.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add igbvf to the list of supported Intel drivers and Alex to the list of
maintainers.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When testing the "e1000: enhance frame fragment detection" (and e1000e)
patches we found some bugs with reducing the MTU size.  The 1024 byte
descriptor used with the 1000 mtu test also (re) introduced the
(originally) reported bug, and causes us to need the e1000_clean_tx_irq
"enhance frame fragment detection" fix.

So what has occured here is that 2.6.32 is only vulnerable for mtu <
1500 due to the jumbo specific routines in both e1000 and e1000e.
So, 2.6.32 needs the 2kB buffer len fix for those smaller MTUs, but
is not vulnerable to the original issue reported.  It has been pointed
out that this vulnerability needs to be patched in older kernels that
don't have the e1000 jumbo routine.  Without the jumbo routines, we
need the "enhance frame fragment detection" fix the e1000, old
e1000e is only vulnerable for < 1500 mtu, and needs a similar
fix.  We split the patches up to provide easy backport paths.

There is only a slight bit of extra code when this fix and the
original "enhance frame fragment detection" fixes are applied, so
please apply both, even though it is a bit of overkill.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fmvj18x_cs, serial_cs:
 add new id
 Panasonic lan & modem card (model name:AL-VML101)
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only the first two fields of mcc wrb - embedded, payload_len
need to be cpu_to_le32() swapped while issuing a cmd to the hw.
The fields tag0, tag1 are opaque and returned back to cpu as is...
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Please add support for Microsoft MN-120 PCMCIA network card. It's an
old card, I know, but adding support is very easy. You just need to
get tulip_core.c to recognise its vendor/device ID.

Patch for kernel 2.6.32.4 (and many previous) attached.

 .....Ron Murray
Signed-off-by: NRon Murray <rjmx@rjmx.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pages are posted to the rxq in such a way that more than one frag
can share the page. The last frag that uses the page unmaps the
page.  In the case when a page is not fully used (due to lack of space in rxq)
the last frag that uses the page is not being set as a "last_page_user";
instead, the next frag in the rxq is incorrectly being set.

The fix has also been tested on ppc64 with 64k pages...
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Intel WiMax Wireless Link 6050 can show under more than one USB
ID. Add support for all, introducing a generic flag (i2400mu->i6050)
that denotes a 6x50 based device.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf: x86: Add support for the ANY bit
  perf: Change the is_software_event() definition
  perf: Honour event state for aux stream data
  perf: Fix perf_event_do_pending() fallback callsite
  perf kmem: Print usage help for unknown commands
  perf kmem: Increase "Hit" column length
  hw-breakpoints, perf: Fix broken mmiotrace due to dr6 by reference change
  perf timechart: Use tid not pid for COMM change

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: Reassign prev and switch_count when reacquire_kernel_lock() fail
  sched: Fix vmark regression on big machines

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: retry FS IOs even if it has failed with AC_ERR_INVALID

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  tty: fix race in tty_fasync
  serial: serial_cs: oxsemi quirk breaks resume
  serial: imx: bit &/| confusion
  serial: Fix crash if the minimum rate of the device is > 9600 baud
  serial-core: resume serial hardware with no_console_suspend
  serial: 8250_pnp: use wildcard for serial Wacom tablets
  nozomi: quick fix for the close/close bug
  compat_ioctl: Supress "unknown cmd" message on serial /dev/console

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: hv: fix smp problems in the hyperv core code
  Staging: et131x: Fix 2.6.33rc1 regression in et131x
  Staging: asus_oled: fix oops in 2.6.32.2

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  Revert "sysdev: fix prototype for memory_sysdev_class show/store functions"
  driver-core: fix devtmpfs crash on s390

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: isp1362: fix build failure on ARM systems via irq_flags cleanup
  USB: isp1362: better 64bit printf warning fixes
  USB: fix usbstorage for 2770:915d delivers no FAT
  USB: Fix level of isp1760 Reloading ptd error message
  USB: FHCI: avoid NULL pointer dereference
  USB: Fix duplicate sysfs problem after device reset.
  USB: add speed values for USB 3.0 and wireless controllers
  USB: add missing delay during remote wakeup
  USB: EHCI & UHCI: fix race between root-hub suspend and port resume
  USB: EHCI: fix handling of unusual interrupt intervals
  USB: Don't use GFP_KERNEL while we cannot reset a storage device
  USB: fix bitmask merge error
  usb: serial: fix memory leak in generic driver
  USB: serial: fix USB serial fix kfifo_len locking

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  fs/bio.c: fix shadows sparse warning
  drbd: The kernel code is now equivalent to out of tree release 8.3.7
  drbd: Allow online resizing of DRBD devices while peer not reachable (needs to be explicitly forced)
  drbd: Don't go into StandAlone mode when authentification failes because of network error
  drivers/block/drbd/drbd_receiver.c: correct NULL test
  cfq-iosched: Respect ioprio_class when preempting
  genhd: overlapping variable definition
  block: removed unused as_io_context
  DM: Fix device mapper topology stacking
  block: bdev_stack_limits wrapper
  block: Fix discard alignment calculation and printing
  block: Correct handling of bottom device misaligment
  drbd: check on CONFIG_LBDAF, not LBD
  drivers/block/drbd: Correct NULL test
  drbd: Silenced an assert that could triggered after changing write ordering method
  drbd: Kconfig fix
  drbd: Fix for a race between IO and a detach operation [Bugz 262]
  drbd: Use drbd_crypto_is_hash() instead of an open coded check

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits)
  ACPI: delete acpi_processor_power_verify_c2()
  ACPI: allow C3 > 1000usec
  ACPI: enable C2 and Turbo-mode on Nehalem notebooks on A/C
  ACPI: power_meter: remove double kfree()
  ACPI: processor: restrict early _PDC to opt-in platforms
  ACPI: Fix unused variable warning in sbs.c
  acpi: make ACPI device id constant
  sony-laptop - fix using of uninitialized variable
  ACPI: Fix section mismatch error for acpi_early_processor_set_pdc()
  eeepc-laptop: disable wireless hotplug for 1201N
  eeepc-laptop: add hotplug_disable parameter
  eeepc-laptop: switch to using sparse keymap library
  eeepc-laptop: dmi blacklist to disable pci hotplug code
  eeepc-laptop: disable cpu speed control on EeePC 701
  ACPI: don't cond_resched if irq is disabled
  ACPI: Remove unnecessary cast.
  ACPI: Advertise to BIOS in _OSC: _OST on _PPC changes
  ACPI: EC: Add wait for irq storm
  ACPI: SBS: Move SBS HC callback to faster Notify queue
  x86, ACPI: delete acpi_boot_table_init() return value
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
  ecryptfs: use after free
  ecryptfs: Eliminate useless code
  ecryptfs: fix interpose/interpolate typos in comments
  ecryptfs: pass matching flags to interpose as defined and used there
  ecryptfs: remove unnecessary d_drop calls in ecryptfs_link
  ecryptfs: don't ignore return value from lock_rename
  ecryptfs: initialize private persistent file before dereferencing pointer
  eCryptfs: Remove mmap from directory operations
  eCryptfs: Add getattr function
  eCryptfs: Use notify_change for truncating lower inodes

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: fix possible panic on unmount
  Btrfs: deal with NULL acl sent to btrfs_set_acl
  Btrfs: fix regression in orphan cleanup
  Btrfs: Fix race in btrfs_mark_extent_written
  Btrfs, fix memory leaks in error paths
  Btrfs: align offsets for btrfs_ordered_update_i_size
  btrfs: fix missing last-entry in readdir(3)

In free_unmap_area_noflush(), va->flags is marked as VM_LAZY_FREE first, and
then vmap_lazy_nr is increased atomically.

But, in __purge_vmap_area_lazy(), while traversing of vmap_are_list, nr
is counted by checking VM_LAZY_FREE is set to va->flags.  After counting
the variable nr, kernel reads vmap_lazy_nr atomically and checks a
BUG_ON condition whether nr is greater than vmap_lazy_nr to prevent
vmap_lazy_nr from being negative.

The problem is that, if interrupted right after marking VM_LAZY_FREE,
increment of vmap_lazy_nr can be delayed.  Consequently, BUG_ON
condition can be met because nr is counted more than vmap_lazy_nr.

It is highly probable when vmalloc/vfree are called frequently.  This
scenario have been verified by adding delay between marking VM_LAZY_FREE
and increasing vmap_lazy_nr in free_unmap_area_noflush().

Even the vmap_lazy_nr is for checking high watermark, it never be the
strict watermark.  Although the BUG_ON condition is to prevent
vmap_lazy_nr from being negative, vmap_lazy_nr is signed variable.  So,
it could go down to negative value temporarily.

Consequently, removing the BUG_ON condition is proper.

A possible BUG_ON message is like the below.

   kernel BUG at mm/vmalloc.c:517!
   invalid opcode: 0000 [#1] SMP
   EIP: 0060:[<c04824a4>] EFLAGS: 00010297 CPU: 3
   EIP is at __purge_vmap_area_lazy+0x144/0x150
   EAX: ee8a8818 EBX: c08e77d4 ECX: e7c7ae40 EDX: c08e77ec
   ESI: 000081fe EDI: e7c7ae60 EBP: e7c7ae64 ESP: e7c7ae3c
   DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
   Call Trace:
   [<c0482ad9>] free_unmap_vmap_area_noflush+0x69/0x70
   [<c0482b02>] remove_vm_area+0x22/0x70
   [<c0482c15>] __vunmap+0x45/0xe0
   [<c04831ec>] vmalloc+0x2c/0x30
   Code: 8d 59 e0 eb 04 66 90 89 cb 89 d0 e8 87 fe ff ff 8b 43 20 89 da 8d 48 e0 8d 43 20 3b 04 24 75 e7 fe 05 a8 a5 a3 c0 e9 78 ff ff ff <0f> 0b eb fe 90 8d b4 26 00 00 00 00 56 89 c6 b8 ac a5 a3 c0 31
   EIP: [<c04824a4>] __purge_vmap_area_lazy+0x144/0x150 SS:ESP 0068:e7c7ae3c

[ See also http://marc.info/?l=linux-kernel&m=126335856228090&w=2 ]
Signed-off-by: NYongseok Koh <yongseok.koh@samsung.com>
Reviewed-by: NMinchan Kim <minchan.kim@gmail.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh64: wire up sys_accept4.
  sh: unwire sys_recvmmsg.
  sh: ms7724: Correct sh-eth EEPROM polling timeout.

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 5888/1: arm: Update comments in cacheflush.h and remove unnecessary V6 and V7 comments
  ARM: 5886/1: arm: Fix cpu_proc_fin() for proc-v7.S and make kexec work
  ARM: 5885/1: arm: Flush TLB entries in setup_mm_for_reboot()
  ARM: 5884/1: arm: Fix DCC console for v7
  ARM: 5883/1: Revert "disable NX support for OABI-supporting kernels"
  ARM: 5882/1: ARM: Fix uncompress code compile for different defines of flush(void)
  ARM: fix badly placed mach/plat entries in Kconfig & Makefile

Propagate the ANY bit into the fixed counter config for v3 and higher.
Signed-off-by: NStephane Eranian <eranian@google.com>
[a.p.zijlstra@chello.nl: split from larger patch]
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4b5430c6.0f975e0a.1bf9.ffff85fe@mx.google.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The is_software_event() definition always confuses me because its an
exclusive expression, make it an inclusive one.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Anton reported that perf record kept receiving events even after calling
ioctl(PERF_EVENT_IOC_DISABLE). It turns out that FORK,COMM and MMAP
events didn't respect the disabled state and kept flowing in.
Reported-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: NAnton Blanchard <anton@samba.org>
LKML-Reference: <1263459187.4244.265.camel@laptop>
CC: stable@kernel.org
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Paul questioned the context in which we should call
perf_event_do_pending(). After looking at that I found that it should be
called from IRQ context these days, however the fallback call-site is
placed in softirq context. Ammend this by placing the callback in the IRQ
timer path.
Reported-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1263374859.4244.192.camel@laptop>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Assume A->B schedule is processing, if B have acquired BKL before and it
need reschedule this time. Then on B's context, it will go to
need_resched_nonpreemptible for reschedule. But at this time, prev and
switch_count are related to A. It's wrong and will lead to incorrect
scheduler statistics.
Signed-off-by: NYong Zhang <yong.zhang0@gmail.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <2674af741001102238w7b0ddcadref00d345e2181d11@mail.gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

SD_PREFER_SIBLING is set at the CPU domain level if power saving isn't
enabled, leading to many cache misses on large machines as we traverse
looking for an idle shared cache to wake to.  Change the enabler of
select_idle_sibling() to SD_SHARE_PKG_RESOURCES, and enable same at the
sibling domain level.
Reported-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NMike Galbraith <efault@gmx.de>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1262612696.15495.15.camel@marge.simson.net>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Originally patched by Neil Horman <nhorman@tuxdriver.com>

e1000e could with a jumbo frame enabled interface, and packet split disabled,
receive a packet that would overflow a single rx buffer.  While in practice
very hard to craft a packet that could abuse this, it is possible.

this is related to CVE-2009-4538
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Originally From: Neil Horman <nhorman@tuxdriver.com>
Modified by: Jesse Brandeburg <jesse.brandeburg@intel.com>

Hey all-
	A security discussion was recently given:
http://events.ccc.de/congress/2009/Fahrplan//events/3596.en.html
And a patch that I submitted awhile back was brought up.  Apparently some of
their testing revealed that they were able to force a buffer fragment in e1000
in which the trailing fragment was greater than 4 bytes.  As a result the
fragment check I introduced failed to detect the fragement and a partial
invalid frame was passed up into the network stack.  I've written this patch
to correct it.  I'm in the process of testing it now, but it makes good
logical sense to me.  Effectively it maintains a per-adapter state variable
which detects a non-EOP frame, and discards it and subsequent non-EOP frames
leading up to _and_ _including_ the next positive-EOP frame (as it is by
definition the last fragment).  This should prevent any and all partial frames
from entering the network stack from e1000.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable count and i are unsigned so the (<|>=)0 tests do not work.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was some left over #ifdef ARM logic that is outdated but no one
really noticed.  So instead of relying on this tricky logic, properly
load and utilize the platform irq_flags resources.
Reported-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NLothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some hosts that treat the return value of sizeof differently from unsigned
long might still hit warnings.  So use %zu for sizeof() values.  This is a
better version of the previous commit b0a9cf29.
Signed-off-by: NLothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Resolves kernel.org bug 14914.

Remove entry for 2770:915d (usb digital camera with mass storage
support) from unusual_devs.h. The fix triggered by the entry causes
the file system on the camera to be completely inaccessible (no
partition table, the device is not mountable).

The patch works, but let me clarify a few things about it.  All the
patch does is remove the entry for this device from the
drivers/usb/storage/unusual_devs.h, which is supposed to help with a
problem with the device's reported size (I think).  I'm pretty sure it
was originally added for a reason, so I'm not sure removing it won't
cause other problems to reappear.  Also, I should note that this
unusual_devs.h entry was present (and activating workarounds) in
2.6.29, but in that version everything works fine.  Starting with
2.6.30, things no longer work.
Signed-off-by: NRyan May <rmay31@gmail.com>
Cc: Rohan Hart <rohan.hart17@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This error message is not actually an error, it's an information
message. It is triggered when a transfer which ended in a NAQ is
retried successfully by the hardware.
Signed-off-by: NColin Tuckley <colin.tuckley@arm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>