We need to set the extended radio parameters for wl127x only.
Currently, we were only calling this command with wl127x STA mode, but
we should also do it for AP mode.

Move the call to the extended radio paramaters to the common hw_init
and use a single if for the chip type to do everything at once.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We should not get an hlid value bigger than WL12XX_MAX_LINKS from
wl1271_rx_handle_data().  We have a WARN_ON in case it happens.  But
despite the warning, we would still go ahead and write the hlid bit
into active_hlids (a stack variable).  This would cause us to
overwrite other data in the stack.

To avoid this problem, we now skip the write when issuing the warning,
so at least we don't corrupt data.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Commit 80900d01 accidently broke
the ABI for testmode commands. Restore the ABI again.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NLuciano Coelho <coelho@ti.com>

ieee80211_free_txskb should be used when dropping a frame in the device
rx path such that mac80211 knows about this frame being dropped.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

cfg_workqueue was added to notify cfg80211 that scan, connect
or disconnect is done by calling respective completion handlers.
We can avoid use of this workqueue by calling those handlers
from other places.
1) Call connect, disconnect completion handlers in their callback
   functions.
   ex. Call cfg80211_connect_result() in mwifiex_cfg80211_connect()
2) Call scan completion handler after parsing response of last scan
   command in a queue.

After removing the workqueue, variables (assoc_request etc.) and
checks used for mutual exclusion become redundant. Those are also
removed in this patch.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My previous patch
34a5b4b6 iwlwifi: do not re-configure
HT40 after associated

Fix the case of HT40 after association on specified AP, but it break the
association for some APs and cause not able to establish connection.
We need to address HT40 before and after addociation.

CC: stable@vger.kernel.org #3.0+
Reported-by: NAndrej Gelenberg <andrej.gelenberg@udo.edu>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: NAndrej Gelenberg <andrej.gelenberg@udo.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ted reported that he couldn't connect to some APs
and bisected it to the tx_sync implementation.
Disable it for the BSS context to fix this issue.
Reported-by: NTed Ts'o <tytso@mit.edu>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Command cancel path cancels the current command and moves
it to free command queue. While doing that it deletes the
command entry from the pending list. This is not correct
as the entry has been already deleted from the pending
list at 'mwifiex_exec_next_cmd'. Fixing it.

Also making sure the stale command pointer is cleaned and
unaccessible for later use.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Avoids this:

ERROR: "bcma_chipco_pll_write" [drivers/net/wireless/b43/b43.ko] undefined!
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mwifiex driver no longer supports it's own custom regulatory rules,
but custom regulatory domain capability is still advertised during
wiphy registration by the driver.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The brcmsmac driver has been verified on chipsets that were supported
when it was a pci device driver, ie. bcm4313, bcm43224, and bcm43225.
This patch restricts the driver to 802.11 core revisions that are found
in these chipsets.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of storing the buscore information now the BCMA core device
is kept for quick reference in si_info structure.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Number of fields are no longer needed as the BCMA provides it
or makes them redundant. These have been removed.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In aiutils.c the selected core was maintained by its index number. This
is obsolete using BCMA functions so several functions using that index
have been removed.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function ai_switch_core() is no longer needed and its counterpart
ai_restore_core() as well, because interrupts disabling is not needed
anymore.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to interrupt disable/enable functionality any
longer due to BCMA usage assures the correct core is accessed
in any context.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The macros were used to assure that the correct core was accessed in
the ISR, but register access is now done giving the explicit core so
no need to change interrupt state.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A number of functions in pmu.c are not used or adding no functionality
at all. These have been removed.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The register access macros like R_REG/W_REG/etc. are no longer
needed as the driver uses the BCMA provided functions.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code in aiutils.c now uses the BCMA function for control the
registers in the device cores.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code in pmu.c now uses the functions provided by BCMA to
access the core registers.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code in srom.c now uses the core access function provided by
BCMA so no need to pass __iomem pointer any longer.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code in otp.c now uses the bcma core access functions to
read the OTP information from the device.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of returning the core index the function now returns
the bcma device for the requested core id. This function is
now exposed in the header file.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Specs were updated.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The order is different than on older PHYs.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With previous patch "rtlwifi: use work for lps" we can now use mutex for
protecting ps mode changing critical sections. This fixes running system
with interrupts disabled for long time.

Merge ips_lock and lps_lock as they seems to protect the same data
structures (accessed in rtl_ps_set_rf_state() function).
Reported-by: NPhilipp Dreimann <philipp@dreimann.net>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Mike McCormack <mikem@ring3k.org>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Leaving leisure power save mode can take some time, so it's better to
perform that action in process context with interrupts enabled. This
patch changes lps_leave tasklet to work.
Reported-by: NPhilipp Dreimann <philipp@dreimann.net>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Mike McCormack <mikem@ring3k.org>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Changes were obtained from MMIO dump from 5.100.82.112.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

replace single queue function calls with equivalent multiple queue
functions. Wakeup queue and stop queue calls are guarded by spin lock.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Free SKBs allocated during multiport aggrgation setup when RX
multiport aggregation fails in the middle. With this handling
freeing SKB in mwifiex_process_int_status() for failure case
is removed.

Also handles single RX transaction failure.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Event buffers for PCIe interface are allocated during driver
initialisation, and respective physical addresses are sent to FW
in *_PCIE_DESC_DETAILS command so that FW can do DMA. These buffers
will be freed while unloading the driver. Therefore we should not
free them in event handling error path. Also we should skip next
pending events in failure case.

Also fixed 'returning -1 instead of -ENOMEM is sloppy' warnings.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>