Add board support with device tree for Hisilicon Hi3620 SoC platform.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
[khilman: fix checkpatch errors]
[khilman: fold in patch which selects GPIO in Kconfig]
Signed-off-by: NKevin Hilman <khilman@linaro.org>

To avoid having to make every text section swap the instruction order
of all instructions, make sure modules are built also built with --be8
(as is the current kernel final link).

If we do not do this, we would end up having to swap all instructions
when loading a module, instead of just the instructions that we are
applying ELF relocations to.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: NDave Martin <Dave.Martin@arm.com>

Install targets (install, zinstall, uinstall) on arm have a dependency
to vmlinux. This may cause parts of the kernel to be rebuilt during
installation. We must avoid this since this may run as root. Install
targets "ABSOLUTELY MUST NOT MODIFY THE SOURCE TREE." as Linus
emphasized this in:

 http://lkml.org/lkml/2013/7/10/600

So on arm and maybe other archs we need the same as for x86:

 1648e4f8 x86, kbuild: make "make install" not depend on vmlinux

This patch fixes this for arm. Dependencies are removed and instead a
check to install.sh is added for the files that are needed.

This issue was uncovered by this build error where the -j option is
used in conjunction with install targets:

 $ make <makeflags>
 $ make <makeflags> zinstall
 ...
   DEPMOD
 Usage: .../scripts/depmod.sh /sbin/depmod <kernelrelease>

(INSTALL_MOD_PATH and INSTALL_PATH variables set, so no root perms
required in this case.)

The problem is that zinstall on arm due to its dependency to vmlinux
does a prepare/prepare3 and finally does a forced rewrite of
kernel.release even if it exists already.

Rebuilding kernel.release removes it first and then recreates it. This
might race with another parallel make job running depmod.

So this patch should fix this one too.

Also quoting $(KERNELRELEASE) arg for install.sh as this messes
argument order in case it is empty (which is the case if the kernel
was not built yet).
Signed-off-by: NRobert Richter <robert.richter@linaro.org>
Signed-off-by: NRobert Richter <rric@kernel.org>
Acked-by: Michal Marek <mmarek@suse.cz>.
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: N"Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: NMichal Marek <mmarek@suse.cz>

The Shark machine sub-architecture (also known as DNARD, the
DIGITAL Network Appliance Reference Design) lacks a maintainer
able to apply and test patches to modernize the architecture.

It is suspected that the current kernel, while it compiles,
does not even boot on this machine. The listed maintainer has
expressed that he will not be able to spend any time on the
maintenance for the coming year.

So let's delete it from the kernel for now. It can always be
resurrected with git revert if maintenance is resumed.

As the VIA82c505 PCI adapter was only used by this
architecture, that gets deleted too.

Cc: arm@kernel.org
Cc: Alexander Schulz <alex@shark-linux.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

So, there's a comment I put at the top of this, which people seem to
fail to read.  So let's fix it for them instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add ARCH_SHMOBILE_MULTI to mach-shmobile that can be used
to enable ARCH_MULTIPLATFORM on selected SoCs and boards.

The headers stay under arch/arm/mach-shmobile/include/mach/
for now, they can and will be migrated independently over time.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Starting up the C compiler can be a slow operation on some systems.
Though these calls don't individually take a lot of time, they add up.
Rearrange the ARM Makefile a bit to avoid extra calls to the compiler
when they can be easily avoided.

When running with the Chrome OS ARM cross compiler
"armv7a-cros-linux-gnueabi-", this shaved .55 seconds (from 5.31
seconds to 4.76 seconds) off an incremental build of the kernel:
  time make -j32 ARCH=arm CROSS_COMPILE=armv7a-cros-linux-gnueabi-

Thanks to Mike Frysinger for the clean trick to make this work.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The %.dtb dependency is specified to depend on the PHONY "scripts".
That means that it'll build every time even if the underlying dtb file
hasn't been touched.  Use an order-only prerequisites to fix this.
Also mark "dtbs" as PHONY for correctness.

This was broken in (70b0476a ARM: 7513/1: Make sure dtc is built before
running it).
Reported-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Reviewed-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The STiH415 is the next generation of HD, AVC set-top box processors for
satellite, cable, terrestrial and IP-STB markets. It is an ARM Cortex-A9
1.0 GHz, dual-core CPU.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Stuart Menefy <stuart.menefy@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch adds support for the TI-Nspire platform.

Changes between v1 and v2:
* Added GENERIC_IRQ_CHIP to platform Kconfig
Signed-off-by: NDaniel Tang <dt.tangr@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This adds a generic devicetree board file and a dtsi for boards
based on the RK3066a SoCs from Rockchip.

Apart from the generic parts (gic, clocks, pinctrl) the only components
currently supported are the timers, uarts and mmc ports (all DesignWare-
based).
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NOlof Johansson <olof@lixom.net>

I got a build error today that made me realize that it is not
possible to build a kernel for a SiRF platform without enabling
CONFIG_PRIMA2, since a lot of common code depends on CONFIG_PRIMA2.

This fixes all occurences that appear like common SiRF code.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NMark Brown <broonie@linaro.org>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NBarry Song <Baohua.Song@csr.com>
Acked-by: NMike Turquette <mturquette@linaro.org>

After removing support for ATAGS based boot on Exynos, there is not much
that can be shared between Exynos and other S5P platforms. This patch
makes Exynos a standalone Samsung platform, not using PLAT_S5P.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Texas Instruments Keystone family of multi-core devices are
based on ARM Cortex A15. Patch adds basic definitions for a
new Keystone sub-architecture in ARM.

The TCI66xxK2H Communications Infrastructure Keystone SoCs
are member of the C66x family based on TI's new KeyStone 2
multi-core SoC Architecture designed specifically for high
performance wireless and networking infrastructure applications.
The SOCs contains many subsystems like Cortex A15 ARM CorePacs,
C66XX DSP CorePacs, MSMC memory controller, Tera Net bus,
IP Network, Navigator, Hyperlink, 1G/10G Ethernet, Radio layers
and queue based communication systems.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: arm@kernel.org
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Clean up some trailing whitespace issues in arch/arm/Makefile.
Signed-off-by: NDaniel Tang <dt.tangr@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch modifies the required Kconfig and Makefile files to allow the
building of kernel for Cortex-M3.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Reviewed-by: NJonathan Austin <jonathan.austin@arm.com>
Tested-by: NJonathan Austin <jonathan.austin@arm.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

The platform was merged about 10 years ago, and has seen few updates
for most of the time since. The people that merged the code seem
no longer interested in it either, so let's remove it now.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NRobert Schwebel <r.schwebel@pengutronix.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>

There are no conflicting files between the three mach-spear* directories
and plat-spear any more, so we can now move all file to a common
mach-spear directory.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>

This patch is for just moving plat-s3c24xx/*.c into mach-s3c24xx/, so
that we could remove plat-s3c24xx directory. But since the PLAT_S3C24XX
is used in drivers, the statement is not deleted and it will be sorted
out next time.

Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add support for the smallest, dumbest possible platform, to be
used as a guest for KVM or other hypervisors.

It only mandates a GIC and architected timers. Fits nicely with
a multiplatform zImage. Uses very little silicon area.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
[will: fixed up conflicts with GIC move to drivers/irqchip/]
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Targets KVM support for Cortex A-15 processors.

Contains all the framework components, make files, header files, some
tracing functionality, and basic user space API.

Only supported core is Cortex-A15 for now.

Most functionality is in arch/arm/kvm/* or arch/arm/include/asm/kvm_*.h.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Reviewed-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <c.dall@virtualopensystems.com>

This patch moves mach-s3c2440/pll into mach-s3c24xx/
and removes arch/arm/mach-s3c2440/ directory in kernel.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch moves mach-s3c2412/cpufreq driver into mach-s3c24xx/
and removes arch/arm/mach-s3c2412/ directory in kernel.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Recent ARMv7 toolchains assume that unaligned memory accesses will not
fault and will instead be handled by the processor.

For the nommu case (without an MPU), memory will be treated as
strongly-ordered and therefore unaligned accesses may fault regardless
of the SCTLR.A setting.

This patch passes -mno-unaligned-access to GCC when compiling for nommu
targets, preventing the generation of unaligned memory access in the
kernel.
Acked-by: NNicolas Pitre <nico@linaro.org>
Tested-by: NJonathan Austin <jonathan.austin@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The current rules have the .dtb files build in a different directory
from the .dts files. The only reason for this is that it was what
PowerPC has done historically. This patch changes ARM to use the generic
dtb rule which builds .dtb files in the same directory as the source .dts.

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: NOlof Johansson <olof@lixom.net>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
[swarren: added rm command for old stale .dtb files]
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

In order to start upstreaming Broadcom SoC support, create
a starting hierarchy, arch and dts files.
The first support SoC family that is planned is the
BCM281XX (BCM11130/11140/11351/28145/28155) family of dual A9 mobile
SoC cores.
This code is just the skeleton code for get the machine upstreamed. It
has been made MULTIPLATFORM compatible.
Next steps
----------
Upstream a basic set of drivers - sufficient for a console boot to
ramdisk. These will includer timer, gpio, i2c drivers.
After this basic set, we will proceed with a more comprehensive set
of drivers for the 281XX SoC family.

v2 patch mods
--------
 - Remove l2x0_of_init call as there were problems with the code.
   A separate patch will be submitted with cache init code
 - Rename capri files and refs to bcm281xx-based names
 - Add bcm281xx binding doc
 - various misc cleanups

v3 patch mods
-------------
 - Remove extra #include lines
 - Remove remaining references to capri
 - dt uart chipset string added
 - cleaned up chip # references

v4 patch mods
-------------
 - swap order of compatible definitions for uart
 - fix typo

v5 patch mods
-------------
 - Rename bcm281xx to bcm11351 in dts+code,
   leaving references to bcm281xx only in help+comments.

v6 patch mods
-------------
 - fix typo in uart 'compatible' string
Signed-off-by: NChristian Daudt <csd@broadcom.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NStefan Roese <sr@denx.de>

This moves the MTU timer driver from arch/arm/plat-nomadik
to drivers/clocksource and moves the header file to the
platform_data directory.

As this moves the last file being compiled to an object out
of arch/arm/plat-nomadik, we have to "turn off the light"
and delete the plat-nomadik directory, because it is not
allowed to have an empty Makefile in a plat-* directory.
This is probably also a desired side effect of depopulating
the arch/arm directory of drivers. Luckily we have just
deleted all the <plat/*> include files prior to this so
by moving the last one we may delete the directory.

After this all the Ux500 and Nomadik device drivers live
outside of the arch/arm hierarchy.

Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The Zynq support in mainline does not (yet) make use of any of the
generic clk or clk lookup functionality.  Remove what is upstream for
now, until the out-of-tree implementation is in suitable form for
merging.

An important side effect of this patch is that it allows the building of
a Zynq kernel without running into unresolved symbol problems:

   drivers/built-in.o: In function `amba_get_enable_pclk':
   clkdev.c:(.text+0x444): undefined reference to `clk_enable'
   drivers/built-in.o: In function `amba_remove':
   clkdev.c:(.text+0x488): undefined reference to `clk_disable'
   drivers/built-in.o: In function `amba_probe':
   clkdev.c:(.text+0x540): undefined reference to `clk_disable'
   drivers/built-in.o: In function `amba_device_add':
   clkdev.c:(.text+0x77c): undefined reference to `clk_disable'
   drivers/built-in.o: In function `enable_clock':
   clkdev.c:(.text+0x29738): undefined reference to `clk_enable'
   drivers/built-in.o: In function `disable_clock':
   clkdev.c:(.text+0x29778): undefined reference to `clk_disable'
   drivers/built-in.o: In function `__pm_clk_remove':
   clkdev.c:(.text+0x297f8): undefined reference to `clk_disable'
   drivers/built-in.o: In function `pm_clk_suspend':
   clkdev.c:(.text+0x29bc8): undefined reference to `clk_disable'
   drivers/built-in.o: In function `pm_clk_resume':
   clkdev.c:(.text+0x29c28): undefined reference to `clk_enable'
   make[2]: *** [vmlinux] Error 1
   make[1]: *** [sub-make] Error 2
   make: *** [all] Error 2

In addition, eliminate Zynq's "use" of the versatile platform, as it is
no longer needed.  As Nick Bowler points out:

   For the record, I think this was introduced by commit 56a34b03
   ("ARM: versatile: Make plat-versatile clock optional") which forgot to
   select PLAT_VERSATILE_CLOCK on Zynq.  This is not all that surprising,
   because the fact that Zynq "uses" PLAT_VERSATILE is secretly hidden in
   the Makefile.

   Nevertheless, the only feature from versatile that Zynq needed was the
   clock support, so this patch should *also* delete the secret use of
   plat-versatile by removing this line from arch/arm/Makefile:

      plat-$(CONFIG_ARCH_ZYNQ)      += versatile
Signed-off-by: NJosh Cartwright <josh.cartwright@ni.com>
Cc: John Linn <john.linn@xilinx.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NMichal Simek <michal.simek@xilinx.com>

It's really unnecessary to have plat-mxc, and let's merge it into
mach-imx.  It's pretty much just a bunch of file renaming and
Kconfig/Makefile merge.

To make the change less invasive, we keep using Kconfig symbol
CONFIG_ARCH_MXC for mach-imx sub-architecture.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The Linaro cross toolchain and probably others nowadays default to
building in THUMB2 mode. When building a kernel for a CPU that does
not support THUMB2, the compiler complains about incorrect flags.
We can work around this by setting -marm for all non-T2 builds.

-marm was passed unconditionally for C files previously, but nothing was
passed to the gcc frontend when processing .S files, resulting in a
warning.  The assembler never defaults to ARM unless -Wa,-mthumb is
supplied explicitly, so the files were still assembled correctly.

This patch makes sure that -marm is passed for .S files too, and also
avoids the redundant gcc -marm -mthumb in Thumb kernels.

Without this patch, building assabet_defconfig results in:

usr/initramfs_data.S:1:0: warning: target CPU does not support THUMB instructions [enabled by default]
arch/arm/nwfpe/entry.S:1:0: warning: target CPU does not support THUMB instructions [enabled by default]
firmware/cis/PCMLM28.cis.gen.S:1:0: warning: target CPU does not support THUMB instructions [enabled by default]
(and many more)
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NDave Martin <dave.martin@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>

Remove mach-bcmring as this is no longer maintained or used.
Signed-off-by: NChristian Daudt <csd@broadcom.com>
Reviewed-by: NJiandong Zheng <jdzheng@broadcom.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic
support for this SoC.

http://www.broadcom.com/products/BCM2835
http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf

Note that the documentation in the latter .pdf assumes the MMU setup
that's used on the "VideoCore" companion processor, and does not document
physical peripheral addresses. Subtract 0x5e000000 to obtain the physical
addresses. This is accounted for by the ranges property in the /soc node
in the device tree.

The BCM2835 SoC is used in the Raspberry Pi. This patch also adds a
minimal device tree for this board; enough to see some very early kernel
boot messages through earlyprintk. However, this patch does not yet
provide a useful booting system.

http://www.raspberrypi.org/.

This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split from 3-4 months ago, and significantly stripped down and
modified since.
Signed-off-by: NChris Boot <bootc@bootc.net>
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NDom Cobley <popcornmix@gmail.com>
Signed-off-by: NDom Cobley <dc4@broadcom.com>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Tools like kisskb are good at finding build regressions in the kernel
sources. However, regressions in the DT desscriptions are not found,
because generally these build systems don't build the DT binary blobs.

Extend the ARM all target to build all enabled DTB files.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Reviewed-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This lets us build a multiplatform kernel for experimental purposes.
However, it will not be useful for any real work, because it relies
on a number of useful things to be disabled for now:

* SMP support must be turned off because of conflicting symbols.
  Marc Zyngier has proposed a solution by adding a new SOC
  operations structure to hold indirect function pointers
  for these, but that work is currently stalled

* We turn on SPARSE_IRQ unconditionally, which is not supported
  on most platforms. Each of them is currently in a different
  state, but most are being worked on.

* A common clock framework is in place since v3.4 but not yet
  being used. Work on this is on its way.

* DEBUG_LL for early debugging is currently disabled.

* THUMB2_KERNEL does not work with allyesconfig because the
  kernel gets too big

[Rob Herring]: Rebased to not be dependent on the mass mach header rename.
As a result, omap2plus, imx, mxs and ux500 are not converted. Highbank,
picoxcell, mvebu, and socfpga are converted.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Acked-by: NJamie Iles <jamie@jamieiles.com>
Cc: Dinh Nguyen <dinguyen@altera.com>

'make dtbs' in a clean tree will try running the dtc before actually
building it.  Make these rules depend upon the scripts to build it.

Cc: <stable@vger.kernel.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add assembler versions of AES and SHA1 for ARM platforms.  This has provided
up to a 50% improvement in IPsec/TCP throughout for tunnels using AES128/SHA1.

Platform   CPU SPeed    Endian   Before (bps)   After (bps)   Improvement

IXP425      533 MHz      big     11217042        15566294        ~38%
KS8695      166 MHz     little    3828549         5795373        ~51%
Signed-off-by: NDavid McCullough <ucdevel@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This patch removes the ARM architecture mach-pnx4008. No direct support or user
feedback since 2006. Acknowledgements from NXP/Philips and Linux arm-soc
maintainers.
Signed-off-by: NRoland Stigge <stigge@antcom.de>

- Basic hypervisor.h and interface.h definitions.
- Skeleton enlighten.c, set xen_start_info to an empty struct.
- Make xen_initial_domain dependent on the SIF_PRIVILIGED_BIT.

The new code only compiles when CONFIG_XEN is set, that is going to be
added to arch/arm/Kconfig in patch #11 "xen/arm: introduce CONFIG_XEN on
ARM".

Changes in v3:

- improve comments.
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Adding core definitions for Altera's SOCFPGA ARM platform.
Mininum support for Altera's SOCFPGA Cyclone 5 hardware.
Signed-off-by: NDinh Nguyen <dinguyen@altera.com>
Reviewed-by: NPavel Machek <pavel@denx.de>
Reviewed-by: NRob Herring <rob.herring@calxeda.com>
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>