Use ssleep() / msleep() [as appropriate]
instead of schedule_timeout() to guarantee the task delays as expected.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Acked-by: NArnaldo Carvalho de Melo <acme@conectiva.com.br>
Signed-off-by: NMaximilian Attems <janitor@sternwelten.at>
Signed-off-by: NDomen Puncer <domen@coderock.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is a follow up to patch 1 regarding "Selective Sub Address
matching with call user data".  It allows use of the Fast-Select-Acceptance
optional user facility for X.25.

This patch just implements fast select with no restriction on response
(NRR).  What this means (according to ITU-T Recomendation 10/96 section
6.16) is that if in an incoming call packet, the relevant facility bits are
set for fast-select-NRR, then the called DTE can issue a direct response to
the incoming packet using a call-accepted packet that contains
call-user-data.  This patch allows such a response.  

The called DTE can also respond with a clear-request packet that contains
call-user-data.  However, this feature is currently not implemented by the
patch.

How is Fast Select Acceptance used?
By default, the system does not allow fast select acceptance (as before).
To enable a response to fast select acceptance,  
After a listen socket in created and bound as follows
	socket(AF_X25, SOCK_SEQPACKET, 0);
	bind(call_soc, (struct sockaddr *)&locl_addr, sizeof(locl_addr));
but before a listen system call is made, the following ioctl should be used.
	ioctl(call_soc,SIOCX25CALLACCPTAPPRV);
Now the listen system call can be made
	listen(call_soc, 4);
After this, an incoming-call packet will be accepted, but no call-accepted 
packet will be sent back until the following system call is made on the socket
that accepts the call
	ioctl(vc_soc,SIOCX25SENDCALLACCPT);
The network (or cisco xot router used for testing here) will allow the 
application server's call-user-data in the call-accepted packet, 
provided the call-request was made with Fast-select NRR.
Signed-off-by: NShaun Pereira <spereira@tusc.com.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Shaun Pereira <spereira@tusc.com.au>

This is the first (independent of the second) patch of two that I am
working on with x25 on linux (tested with xot on a cisco router).  Details
are as follows.

Current state of module:

A server using the current implementation (2.6.11.7) of the x25 module will
accept a call request/ incoming call packet at the listening x.25 address,
from all callers to that address, as long as NO call user data is present
in the packet header.

If the server needs to choose to accept a particular call request/ incoming
call packet arriving at its listening x25 address, then the kernel has to
allow a match of call user data present in the call request packet with its
own.  This is required when multiple servers listen at the same x25 address
and device interface.  The kernel currently matches ALL call user data, if
present.

Current Changes:

This patch is a follow up to the patch submitted previously by Andrew
Hendry, and allows the user to selectively control the number of octets of
call user data in the call request packet, that the kernel will match.  By
default no call user data is matched, even if call user data is present. 
To allow call user data matching, a cudmatchlength > 0 has to be passed
into the kernel after which the passed number of octets will be matched. 
Otherwise the kernel behavior is exactly as the original implementation.

This patch also ensures that as is normally the case, no call user data
will be present in the Call accepted / call connected packet sent back to
the caller 

Future Changes on next patch:

There are cases however when call user data may be present in the call
accepted packet.  According to the X.25 recommendation (ITU-T 10/96)
section 5.2.3.2 call user data may be present in the call accepted packet
provided the fast select facility is used.  My next patch will include this
fast select utility and the ability to send up to 128 octets call user data
in the call accepted packet provided the fast select facility is used.  I
am currently testing this, again with xot on linux and cisco.  
Signed-off-by: NShaun Pereira <spereira@tusc.com.au>

(With a fix from Alexey Dobriyan <adobriyan@gmail.com>)
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: jlamanna@gmail.com

ebtables.c vfree() checking cleanups.

Signed-off by: James Lamanna <jlamanna@gmail.com>
Signed-off-by: NDomen Puncer <domen@coderock.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Nishanth Aravamudan <nacc@us.ibm.com>

Use msleep() instead of schedule_timeout() to guarantee the task
delays as expected. The current code is not wrong, but it does not account for
early return due to signals, so I think msleep() should be appropriate.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NDomen Puncer <domen@coderock.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off by: Chuck Short <zulcss@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides support for registering multiple netpoll clients to the
same network device.  Only one of these clients may register an rx_hook,
however.  In practice, this restriction has not been problematic.  It is
worth mentioning, though, that the current design can be easily extended to
allow for the registration of multiple rx_hooks.

The basic idea of the patch is that the rx_np pointer in the netpoll_info
structure points to the struct netpoll that has rx_hook filled in.  Aside
from this one case, there is no need for a pointer from the struct
net_device to an individual struct netpoll.

A lock is introduced to protect the setting and clearing of the np_rx
pointer.  The pointer will only be cleared upon netpoll client module
removal, and the lock should be uncontested.
Signed-off-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces a netpoll_info structure, which the struct net_device
will now point to instead of pointing to a struct netpoll.  The reason for
this is two-fold: 1) fields such as the rx_flags, poll_owner, and poll_lock
should be maintained per net_device, not per netpoll;  and 2) this is a first
step in providing support for multiple netpoll clients to register against the
same net_device.

The struct netpoll is now pointed to by the netpoll_info structure.  As
such, the previous behaviour of the code is preserved.
Signed-off-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This trivial patch moves the assignment of poll_owner to -1 inside of
the lock.  This fixes a potential SMP race in the code.
Signed-off-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Small patch to save an unecessary call to strlen() : sprintf() gave us
the length, just trust it.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After using this facility for a while to test my changes to the
cipher crypt() layer, I realised that I should've listend to Dave
and made this thing use CPU cycle counters :) As it is it's too
jittery for me to feel safe about relying on the results.

So here is a patch to make it use CPU cycles by default but fall
back to jiffies if the user specifies a non-zero sec value.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing keys used in the speed tests do not pass the 3DES quality check.
This patch makes it use the template keys instead.

Other algorithms can supply template keys through the same interface if needed.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Reyk Floeter <reyk@vantronix.net>

I recently had the requirement to do some benchmarking on cryptoapi, and
I found reyk's very useful performance test patch [1].

However, I could not find any discussion on why that extension (or
something providing a similar feature but different implementation) was
not merged into mainline.  If there was such a discussion, can someone
please point me to the archive[s]?

I've now merged the old patch into 2.6.12-rc1, the result can be found
attached to this email.

[1] http://lists.logix.cz/pipermail/padlock/2004/000010.htmlSigned-off-by: NHarald Welte <laforge@gnumonks.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems that bad code tends to get copied (see test_cipher_speed).  So let's
kill this idiom before it spreads any further.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch just changes the order of structure members.
Signed-off-by: NHarald Welte <laforge@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHarald Welte <laforge@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kconfig option had an extra double quote at the end of the line
which was causing in warning when building.
Signed-off-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

EMU10K1/EMU10K2 driver
Signed-off-by: NJames Courtier-Dutton <James@superbug.co.uk>

VIA82xx driver
Added dxs_support entry for  Soltek SL-K8Tpro-939.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA Codec driver
Adds SPDIF in/out support to the SigmaTel HDA codecs. Now builds
the input mux control element names from the defcfg regs.
Signed-off-by: NMatt <matt@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

VIA82xx driver
Fixed the info text about dxs_support option (suggest dxs_support=5).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Documentation,HDA Codec driver,HDA generic driver,HDA Intel driver
- Fix some invalid configurations, typos in the last patch
- Make init_verbs chainable, so that different configs can share the same
  init_verbs
- Reorder and clean up the source codes in patch_realtek.c
- Add the pin default configuration parser, used commonly in cmedia
  and realtek patch codes.
- Add 'auto' model to ALC880 for auto-configuration from BIOS
  Use this model as default, and 3-stack as fallback
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Control Midlevel
Add const prefix to snd_kcontrol_new_t pointer for better protection.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA Codec driver,HDA Intel driver
Merged the work of pshou <pshou@realtek.com.tw> for the support of
more models with ALC codecs: ALC880 ASUS, Uniwill, FSC1734, generic 6-stack,
and ALC260 HP.  Tests with the real hardwares are appreciated.

The codec patch is cleaned up:  The preset configuration of codecs are
stored in the table and copied to the spec instance.

Added/fixed comments.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA Codec driver
Allow sub_device=0 in board config check.  This means that every device
with the given sub vendor ID will match.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA Codec driver
Clean up and fix ALC-codec support code.

The last addition of bound volume is fixed now to handle correctly
the bound 'mute switches'.  The analog loopback should work better.
The init verbs are fixed together with this change.

The numbers are replaced with macros for better readability.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA Codec driver
Feed front signals to all surround channels if no data is given
for surround channels.

It seems that CLFE works as expected (only center outputs) even if
connected from the front line - at least on my test system.
If this change causes problems on other system (e.g. only the left
channel is transferred to the center channel), please let me know...
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA generic driver
Print all AMP IN values when multiple nodes are connected.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Trident driver
Disable MPU401 support on SIS7018 since it results in kernel freeze.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA Codec driver
Fix the analog loopback volumes of ALC codecs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA Codec driver
Fix the PCM mixer switch for AD1986a (it was a typo).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA Codec driver
Fixed the handling of amp cache in hda-codec driver.
The confliction of cache values with different indices should be fixed now.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

VIA82xx driver
As the original reporter noted, the NO_VRA must be used for loud volumes.
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

CA0106 driver
Signed-off-by: NJames Courtier-Dutton <James@superbug.co.uk>

Documentation
Added documentation for HDSP MADI driver by Winfried Ritsch.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDSPM driver,PCI drivers,RME9652 driver
Added RME Hammerfall DSP MADI driver by Winfried Ritsch.
(Moved from alsa-driver tree to mainline.)
Signed-off-by: NTakashi Iwai <tiwai@suse.de>