The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.

In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

i2c0 is connected to the gsl1680 capacitive touch panel controller.
i2c1 is connected to an mma7660 3-axis accelerometer.
i2c2 is connected to the front and back gc0309 camera sensors.
The camera sensors require additional regulators be enabled before
they are available.

All these peripherals are not supported by the kernel yet.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The card detect pin setting was taken from the original fex file,
and is confirmed to work.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that we have R_PIO controller support and the pinmux for R_UART,
add the correct pinctrl properties to the R_UART node.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Ippo-q8h is a tablet circuit board commonly found in cheap Android
tablets with A23 SoCs. There are at least 2 versions of the board, with
different peripherals, such as WiFi chips.

Common features among these tablets include 512 MB DRAM, NAND, MMC, LCD,
capacitive touchscreen, accelerometer, 1 or 2 camera sensors, USB OTG,
microphone and speaker.

v5 of these board designs has a ESP8089 WiFi chip (not supported)
connected to mmc1. This patch adds very basic support.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds the stdout-path property to various i.MX boards. Values
of the property have been taken from barebox, so they should be
correct. Also, the older linux,stdout-path property is converted
to stdout-path.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The PBA-B-01 carrier board can be equipped with either Quad or DualLite/Solo
phyFLEX i.MX6 modules (PFL-A-02).
This moves all common devices into imx6qdl-phytec-pbab01.dtsi. The SoC specific
device trees then just include the pfla01 and pbab01 dtsi files corresponding
to the SoC variant.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds support for SATA on Phytec phyFLEX-i.MX6 Quad module.
Signed-off-by: NAshutosh singh <ashutosh.s@phytec.in>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds support for GPMI-NAND on Phytec phyFLEX-i.MX6 Quad module.
Signed-off-by: NAshutosh singh <ashutosh.s@phytec.in>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds support for USB_HOST on Phytec phyFLEX-i.MX6 Quad module.
Signed-off-by: NAshutosh singh <ashutosh.s@phytec.in>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds support for USB_OTG on Phytec phyFLEX-i.MX6 Quad module.
Signed-off-by: NAshutosh singh <ashutosh.s@phytec.in>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add support for imx6q Phytec phyFLEX-i.MX6 Quad (aka pfla02 and pbab01).
 - Module pfla02
 - Carrier-Board pbab01
Signed-off-by: NChristian Hemp <c.hemp@phytec.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Replace /include/ (dtc) with #include (C pre-processor) for all imx DT
files, so that gcc -E handles the entire include tree, and hence any of
those files can #include some other file e.g. for constant definitions.

This allows future use of #defines and header files in order to define
names for various constants, such as pinctrl settings. Use of those
features will increase the readability of the device tree files.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Just to keep consistency with other dts files, place 'status' entry as the last
one.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Following omap3-evm.dts way, it changes all imx dts files to use label
in board dts to refer to nodes defined by soc dtsi.  Thus, the board
dts files become easier to read and edit with the least indentation
levels.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Basic support for the Ka-Ro i.MX25 based TX25 board.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Cc: Lothar Waßmann <LW@KARO-electronics.de>

Fix serial console node and allow the board to boot again.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add a very basic dt support for mx27_3ds (also known as mx27pdk).
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>