- 09 4月, 2013 11 次提交
-
-
由 Peter Ujfalusi 提交于
We have proper driver stack to handle the pmu_stat LED which is connected PWMB of twl4030. Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 Peter Ujfalusi 提交于
Enable support for the PWMs and LED as PWM drivers. Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 Peter Ujfalusi 提交于
Enable support for the PWMs and LEDs as PWM drivers. Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 AnilKumar Ch 提交于
Add a new address space/memory resource to d_can device tree node. D_CAN RAM initialization is achieved through RAMINIT register which is part of AM33XX control module address space. D_CAN RAM init or de-init should be done by writing instance corresponding value to control module register. Till we have a separate control module driver to write to control module, d_can driver will handle the register writes to control module by itself. So a new address space to represent this control module register is added to d_can driver. Signed-off-by: NAnilKumar Ch <anilkumar@ti.com> Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 AnilKumar Ch 提交于
Add d_can instances to aliases node to get the D_CAN instance number from the driver. To initialize D_CAN message RAM, corresponding instance number is required. To initialize instance 0 message RAM then 0x1 should be written and for instance 1 message RAM, 0x2 should be written to control module register. With device-tree framework ip instance number is "-1" by default for all instances. To get device id/instance number then modules should be added to DT "aliases" node. of_alias_get_id() gives the device id number based on number of alias nodes present in "aliases node". Signed-off-by: NAnilKumar Ch <anilkumar@ti.com> Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 Matthias Brugger 提交于
This is a follow-up to Javier Martinez effort adding initial device tree support to IGEP technology devices [1]. It adds uart1 and uart2 bindings to the generic dtsi for the IGEP boards. [1] http://www.spinics.net/lists/linux-omap/msg83409.htmlSigned-off-by: NMatthias Brugger <matthias.bgg@gmail.com> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 Javier Martinez Canillas 提交于
ISEE IGEP COM Module is an TI OMAP3 SoC computer on module. This patch adds an initial device tree support to boot an IGEP COM Module from the MMC/SD. Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk> Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com> [b-cousson@ti.com: Update the Makefile for 3.8-rc2] Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 Javier Martinez Canillas 提交于
ISEE IGEPv2 is an TI OMAP3 SoC based embedded board. This patch adds an initial device tree support to boot an IGEPv2 from the MMC/SD. Currently is working everything that is supported by DT on OMAP3 SoCs (MMC/SD, GPIO LEDs, EEPROM, TWL4030 audio). Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk> Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com> [benoit.cousson@linaro.org: Update the Makefile for 3.8-rc2] Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 Javier Martinez Canillas 提交于
Add a generic .dtsi device tree source file for the common characteristics across IGEP Technology devices. Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: NMatthias Brugger <matthias.bgg@gmail.com> Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 AnilKumar Ch 提交于
Rename I2C and GPIO nodes according to AM33XX TRM. According to AM33XX TRM device instances are starting from "0" like i2c0, i2c1 and i2c3. Signed-off-by: NPantelis Antoniou <panto@antoniou-consulting.com> [panto@antoniou-consulting.com: initial patch by pantelis's] Signed-off-by: NAnilKumar Ch <anilkumar@ti.com> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 Benoit Cousson 提交于
Merge tag 'omap-devel-b-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into for_3.10/dts_merged
-
- 03 4月, 2013 20 次提交
-
-
由 Roger Quadros 提交于
Provide RESET and Power regulators for the USB PHY, the USB Host port mode and the PHY device. Also provide pin multiplexer information for USB host pins. CC: Benoît Cousson <b-cousson@ti.com> Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Adds device nodes for HS USB Host module, TLL module, OHCI and EHCI controllers. CC: Benoît Cousson <b-cousson@ti.com> Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Adds device nodes for HS USB Host module, TLL module, OHCI and EHCI controllers. CC: Benoît Cousson <b-cousson@ti.com> Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulator and NOP PHY device. VAUX2 supplies the PHY's VCC. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. VAUX2 supplies the PHY's VCC. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Remove deprecated USBHS platform data. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's VCC and RESET regulators and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's VCC and RESET regulators and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's VCC and RESET regulators and the NOP PHY device. Get rid of managing the PHY clock as it will be done by the PHY driver. For that to work we create a clock alias that links the PHY clock name to the PHY device name. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
This helper allows board support code to add the PHY's VCC and RESET regulators which are GPIO controlled as well as the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 01 4月, 2013 9 次提交
-
-
由 Rajendra Nayak 提交于
omap3_noncore_dpll_set_rate() attempts an enable of bypass clk as well as ref clk for every .set_rate attempt on a noncore DPLL, regardless of whether the .set_rate results in the DPLL being locked or put in bypass. Early at boot, while some of these DPLLs are programmed and locked (using .set_rate for the DPLL), this causes an ordering issue. For instance, on OMAP5, the USB DPLL derives its bypass clk from ABE DPLL. If a .set_rate of USB DPLL which programmes the M,N and locks it is called before the one for ABE, the enable of USB bypass clk (derived from ABE DPLL) then attempts to lock the ABE DPLL and fails as the M,N values for ABE are yet to be programmed. To get rid of this ordering needs, enable bypass clk for a DPLL as part of its .set_rate only when its being put in bypass, and only enable the ref clk when its locked. Reported-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NRajendra Nayak <rnayak@ti.com> Signed-off-by: NPaul Walmsley <paul@pwsan.com>
-
由 Paul Walmsley 提交于
_pwrdm_save_clkdm_state_and_activate() tried to test one of its unsigned arguments to determine whether it was less than zero. Fix by moving the error test to the caller. Reported-by: NChen Gang <gang.chen@asianux.com> Signed-off-by: NPaul Walmsley <paul@pwsan.com>
-
由 Rajendra Nayak 提交于
_HWMOD_WAKEUP_ENABLED is currently unused across the hwmod framework. Just get rid of it, so we have one less flag to worry about. Tested-by: NVaibhav Bedia <vaibhav.bedia@ti.com> Signed-off-by: NRajendra Nayak <rnayak@ti.com> Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: NPaul Walmsley <paul@pwsan.com>
-
由 Vaibhav Hiremath 提交于
WDT1 module can take one of the below clocks as input functional clock - - On-Chip 32K RC Osc [default/reset] - 32K from PRCM The On-Chip 32K RC Osc clock is not an accurate clock-source as per the design/spec, so as a result, for example, timer which supposed to get expired @60Sec, but will expire somewhere ~@40Sec, which is not expected by any use-case. The solution here is to switch the input clock-source to PRCM generated 32K clock-source during boot-time itself. Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Benoit Cousson <benoit.cousson@linaro.org> Cc: Paul Walmsley <paul@pwsan.com>
-
由 Vaibhav Hiremath 提交于
This patch adds sysc definitions to the wdt1 hwmod entry, which in-turn makes sure that sysc idle bit-fields are configured to valid state on enable/disable callbacks. With the recent submitted patch from Santosh Shilimkar, "ARM: OMAP2+: hwmod: Don't call _init_mpu_rt_base if no sysc" (commit: 4a98c2d89), it is required to add sysconf information to each valid hwmod entry, else device will not be come out from idle state properly and leads to below kernel crash - [2.190237] Unhandled fault: external abort on non-linefetch (0x1028) at 0xf9e35034 [2.198325] Internal error: : 1028 [#1] SMP ARM [2.203101] Modules linked in: [2.206334] CPU: 0 Not tainted (3.9.0-rc3-00059-gd114294#1) [2.212679] PC is at omap_wdt_disable.clone.5+0xc/0x60 [2.218090] LR is at omap_wdt_probe+0x184/0x1fc Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Benoit Cousson <benoit.cousson@linaro.org> Cc: Paul Walmsley <paul@pwsan.com>
-
由 Linus Torvalds 提交于
-
git://git.infradead.org/users/vkoul/slave-dma由 Linus Torvalds 提交于
Pull slave-dmaengine fixes from Vinod Koul: "Two fixes for slave-dmaengine. The first one is for making slave_id value correct for dw_dmac and the other one fixes the endieness in DT parsing" * 'fixes' of git://git.infradead.org/users/vkoul/slave-dma: dw_dmac: adjust slave_id accordingly to request line base dmaengine: dw_dma: fix endianess for DT xlate function
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media由 Linus Torvalds 提交于
Pull media fixes from Mauro Carvalho Chehab: "For a some fixes for Kernel 3.9: - subsystem build fix when VIDEO_DEV=y, VIDEO_V4L2=m and I2C=m - compilation fix for arm multiarch preventing IR_RX51 to be selected - regression fix at bttv crop logic - s5p-mfc/m5mols/exynos: a few fixes for cameras on exynos hardware" * 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: [media] [REGRESSION] bt8xx: Fix too large height in cropcap [media] fix compilation with both V4L2 and I2C as 'm' [media] m5mols: Fix bug in stream on handler [media] s5p-fimc: Do not attempt to disable not enabled media pipeline [media] s5p-mfc: Fix encoder control 15 issue [media] s5p-mfc: Fix frame skip bug [media] s5p-fimc: send valid m2m ctx to fimc_m2m_job_finish [media] exynos-gsc: send valid m2m ctx to gsc_m2m_job_finish [media] fimc-lite: Fix the variable type to avoid possible crash [media] fimc-lite: Initialize 'step' field in fimc_lite_ctrl structure [media] ir: IR_RX51 only works on OMAP2
-
git://git.kernel.dk/linux-block由 Linus Torvalds 提交于
Pull block fixes from Jens Axboe: "Alright, this time from 10K up in the air. Collection of fixes that have been queued up since the merge window opened, hence postponed until later in the cycle. The pull request contains: - A bunch of fixes for the xen blk front/back driver. - A round of fixes for the new IBM RamSan driver, fixing various nasty issues. - Fixes for multiple drives from Wei Yongjun, bad handling of return values and wrong pointer math. - A fix for loop properly killing partitions when being detached." * tag 'for-linus-20130331' of git://git.kernel.dk/linux-block: (25 commits) mg_disk: fix error return code in mg_probe() rsxx: remove unused variable rsxx: enable error return of rsxx_eeh_save_issued_dmas() block: removes dynamic allocation on stack Block: blk-flush: Fixed indent code style cciss: fix invalid use of sizeof in cciss_find_cfgtables() loop: cleanup partitions when detaching loop device loop: fix error return code in loop_add() mtip32xx: fix error return code in mtip_pci_probe() xen-blkfront: remove frame list from blk_shadow xen-blkfront: pre-allocate pages for requests xen-blkback: don't store dev_bus_addr xen-blkfront: switch from llist to list xen-blkback: fix foreach_grant_safe to handle empty lists xen-blkfront: replace kmalloc and then memcpy with kmemdup xen-blkback: fix dispatch_rw_block_io() error path rsxx: fix missing unlock on error return in rsxx_eeh_remap_dmas() Adding in EEH support to the IBM FlashSystem 70/80 device driver block: IBM RamSan 70/80 error message bug fix. block: IBM RamSan 70/80 branding changes. ...
-