提交 · 2be818a116b22dff518f0d7112e6bed39f2034a1 · openanolis / cloud-kernel

22 3月, 2013 1 次提交

Revert "USB: quatech2: only write to the tty if the port is open." · 2be818a1

由 Greg Kroah-Hartman 提交于 3月 21, 2013

This reverts commit 27b351c5.  It caused
problems with the build.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Bill Pemberton <wfp5p@viridian.itc.virginia.edu>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

2be818a1

19 3月, 2013 3 次提交

TTY: add tty_port_tty_hangup helper · aa27a094

由 Jiri Slaby 提交于 3月 07, 2013

It allows for cleaning up on a considerable amount of places. They did
port_get, hangup, kref_put. Now the only thing needed is to call
tty_port_tty_hangup which does exactly that. And they can also decide
whether to consider CLOCAL or completely ignore that.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

aa27a094

TTY: quatech2, remove unneeded is_open · e4408ce3

由 Jiri Slaby 提交于 3月 07, 2013

tty->ops->break_ctl cannot be called outside the gap between open and
close. So there is no need to check whether the port is open in
break_ctl in quatech2. Remove the check and also that member
completely.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

e4408ce3

TTY: add tty_port_tty_wakeup helper · 6aad04f2

由 Jiri Slaby 提交于 3月 07, 2013

It allows for cleaning up on a considerable amount of places. They did
port_get, wakeup, kref_put. Now the only thing needed is to call
tty_port_tty_wakeup which does exactly that.

One exception is ifx6x60 where tty_wakeup was open-coded. We now call
tty_wakeup properly there.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

6aad04f2

14 3月, 2013 1 次提交

USB: quatech2: only write to the tty if the port is open. · 27b351c5

由 Bill Pemberton 提交于 3月 13, 2013

The commit 2e124b4a removed the checks
that prevented qt2_process_read_urb() from trying to put chars into
ttys that weren't actually opened.  This resulted in 'tty is NULL'
warnings from flush_to_ldisc() when the device was used.

The devices use just one read urb for all ports.  As a result
qt2_process_read_urb() may be called with the current port set to a
port number that has not been opened.  Add a check if the port is open
before calling tty_flip_buffer_push().
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

27b351c5

13 3月, 2013 1 次提交

qcserial: bind to DM/DIAG port on Gobi 1K devices · 3f8bc5e4

由 Dan Williams 提交于 3月 13, 2013

Turns out we just need altsetting 1 and then we can talk to it.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

3f8bc5e4

12 3月, 2013 2 次提交

usb: serial: Add Rigblaster Advantage to device table · a57e82a1

由 Steve Conklin 提交于 3月 07, 2013

The Rigblaster Advantage is an amateur radio interface sold by West Mountain
Radio. It contains a cp210x serial interface but the device ID is not in
the driver.
Signed-off-by: NSteve Conklin <sconklin@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

a57e82a1

qcaux: add Franklin U600 · 2d90e636

由 Dan Williams 提交于 2月 19, 2013

4 ports; AT/PPP is standard CDC-ACM.  The other three (added by this
patch) are QCDM/DIAG, possibly GPS, and unknown.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

2d90e636

11 3月, 2013 1 次提交

usb: cp210x new Vendor/Device IDs · be3101c2

由 Matwey V. Kornilov 提交于 3月 09, 2013

This patch adds support for the Lake Shore Cryotronics devices to
the CP210x driver.

These lines are ported from cp210x driver distributed by Lake Shore web site:
   http://www.lakeshore.com/Documents/Lake%20Shore%20cp210x-3.0.0.tar.gz
and licensed under the terms of GPLv2.

Moreover, I've tested this changes with Lake Shore 335 in my labs.
Signed-off-by: NMatwey V. Kornilov <matwey@sai.msu.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

be3101c2

07 3月, 2013 2 次提交

USB: added support for Cinterion's products AH6 and PLS8 · 1941138e

由 Christian Schmiedl 提交于 3月 06, 2013

add support for Cinterion's products AH6 and PLS8 by adding Product IDs
and USB_DEVICE tuples.
Signed-off-by: NChristian Schmiedl <christian.schmiedl@gemalto.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

1941138e

USB: option: add Huawei E5331 · daec90e7

由 Bjørn Mork 提交于 2月 27, 2013

Another device using CDC ACM with vendor specific protocol to mark
serial functions.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

daec90e7

14 2月, 2013 3 次提交

USB: option: add Huawei "ACM" devices using protocol = vendor · 1f3f6877

由 Bjørn Mork 提交于 2月 13, 2013

The USB device descriptor of one identity presented by a few
Huawei morphing devices have serial functions with class codes
02/02/ff, indicating CDC ACM with a vendor specific protocol. This
combination is often used for MSFT RNDIS functions, and the CDC
ACM class driver will therefore ignore such functions.

The CDC ACM class driver cannot support functions with only 2
endpoints.  The underlying serial functions of these modems are
also believed to be the same as for alternate device identities
already supported by the option driver. Letting the same driver
handle these functions independently of the current identity
ensures consistent handling and user experience.

There is no need to blacklist these devices in the rndis_host
driver. Huawei serial functions will either have only 2 endpoints
or a CDC ACM functional descriptor with bmCapabilities != 0, making
them correctly ignored as "non RNDIS" by that driver.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

1f3f6877

USB: serial: fix null-pointer dereferences on disconnect · b2ca6990

由 Johan Hovold 提交于 2月 13, 2013

Make sure serial-driver dtr_rts is called with disc_mutex held after
checking the disconnected flag.

Due to a bug in the tty layer, dtr_rts may get called after a device has
been disconnected and the tty-device unregistered. Some drivers have had
individual checks for disconnect to make sure the disconnected interface
was not accessed, but this should really be handled in usb-serial core
(at least until the long-standing tty-bug has been fixed).

Note that the problem has been made more acute with commit 0998d063
("device-core: Ensure drvdata = NULL when no driver is bound") as the
port data is now also NULL when dtr_rts is called resulting in further
oopses.
Reported-by: NChris Ruehl <chris.ruehl@gtsys.com.hk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

b2ca6990

USB: option: add Yota / Megafon M100-1 4g modem · cd565279

由 Bjørn Mork 提交于 2月 12, 2013

Interface layout:

 00 CD-ROM
 01 debug COM port
 02 AP control port
 03 modem
 04 usb-ethernet

Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0408 ProdID=ea42 Rev= 0.00
S:  Manufacturer=Qualcomm, Incorporated
S:  Product=Qualcomm CDMA Technologies MSM
S:  SerialNumber=353568051xxxxxx
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

cd565279

02 2月, 2013 3 次提交

USB: ftdi_sio: add Zolix FTDI PID · 0ba3b2cc

由 Petr Kubánek 提交于 2月 01, 2013

Add support for Zolix Omni 1509 monochromator custom USB-RS232 converter.
Signed-off-by: NPetr Kubánek <petr@kubanek.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

0ba3b2cc

USB: option: add Changhong CH690 · d4fa6815

由 Bjørn Mork 提交于 2月 01, 2013

New device with 3 serial interfaces:

 If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend) Sub=ff Prot=ff
 If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend) Sub=ff Prot=ff
 If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend) Sub=ff Prot=ff
 If#= 3 Alt= 0 #EPs= 2 Cls=08(stor) Sub=06 Prot=50

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

d4fa6815

USB: ftdi_sio: add PID/VID entries for ELV WS 300 PC II · c249f911

由 Sven Killig 提交于 2月 01, 2013

Add PID/VID entries for ELV WS 300 PC II weather station
Signed-off-by: NSven Killig <sven@killig.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

c249f911

31 1月, 2013 1 次提交

USB: add OWL CM-160 support to cp210x driver · 8de7f4da

由 Luis Llorente Campo 提交于 1月 31, 2013

This adds support for the OWL CM-160 electricity monitor to the cp210x
driver.
Signed-off-by: NLuis Llorente <luisllorente@luisllorente.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

8de7f4da

30 1月, 2013 2 次提交

USB: option: add support for Telit LE920 · 03eb466f

由 Daniele Palmas 提交于 1月 28, 2013

Add PID and special handling for Telit LE920
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

03eb466f

USB: qcserial: add Telit Gobi QDL device · 78796ae1

由 Daniele Palmas 提交于 1月 28, 2013

Add VID and PID for Telit Gobi QDL device
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

78796ae1

26 1月, 2013 1 次提交

usb: add driver for xsens motion trackers · 59e931c4

由 Frans Klaver 提交于 1月 25, 2013

Signed-off-by: NFrans Klaver <frans.klaver@xsens.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

59e931c4

25 1月, 2013 1 次提交

USB: option: add and update Alcatel modems · f8f0302b

由 Bjørn Mork 提交于 1月 23, 2013

Adding three currently unsupported modems based on information
from .inf driver files:

  Diag  VID_1BBB&PID_0052&MI_00
  AGPS  VID_1BBB&PID_0052&MI_01
  VOICE VID_1BBB&PID_0052&MI_02
  AT    VID_1BBB&PID_0052&MI_03
  Modem VID_1BBB&PID_0052&MI_05
  wwan  VID_1BBB&PID_0052&MI_06

  Diag  VID_1BBB&PID_00B6&MI_00
  AT    VID_1BBB&PID_00B6&MI_01
  Modem VID_1BBB&PID_00B6&MI_02
  wwan  VID_1BBB&PID_00B6&MI_03

  Diag  VID_1BBB&PID_00B7&MI_00
  AGPS  VID_1BBB&PID_00B7&MI_01
  VOICE VID_1BBB&PID_00B7&MI_02
  AT    VID_1BBB&PID_00B7&MI_03
  Modem VID_1BBB&PID_00B7&MI_04
  wwan  VID_1BBB&PID_00B7&MI_05

Updating the blacklist info for the X060S_X200 and X220_X500D,
reserving interfaces for a wwan driver, based on

  wwan VID_1BBB&PID_0000&MI_04
  wwan VID_1BBB&PID_0017&MI_06

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

f8f0302b

19 1月, 2013 6 次提交

tty: Added a CONFIG_TTY option to allow removal of TTY · 4f73bc4d

由 Joe Millenbach 提交于 1月 17, 2013

The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.

The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer.  Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.

bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY.  The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.

add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function                                     old     new   delta
chr_dev_init                                 166     170      +4
allow_signal                                  80      82      +2
static.__warned                              143     142      -1
disallow_signal                               63      62      -1
__set_special_pids                            95      94      -1
unregister_console                           126     121      -5
start_kernel                                 546     541      -5
register_console                             593     588      -5
copy_from_user                                45      40      -5
sys_setsid                                   128     120      -8
sys_vhangup                                   32      19     -13
do_exit                                     1543    1526     -17
bitmap_zero                                   60      40     -20
arch_local_irq_save                          137     117     -20
release_task                                 674     652     -22
static.spin_unlock_irqrestore                308     260     -48
Signed-off-by: NJoe Millenbach <jmillenbach@gmail.com>
Reviewed-by: NJamey Sharp <jamey@minilop.net>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

4f73bc4d

USB: io_ti: kill custom closing_wait implementation · f40d7815