When a whole class of devices (possibly from a specific vendor, or
across multiple vendors) require a quirk, explictly listing all devices
in the class make the quirks table unnecessarily large. Fix this by
allowing matching devices based on interface information.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Ensure that intfdata always is NULL if no driver is bound:
1) drvdata is for a driver to store a pointer to driver specific data
2) If no driver is bound, there is no driver specific data associated with
   the device
3) Thus logically drvdata should be NULL if no driver is bound.

We already set intfdata to NULL when a driver is unbound, to ensure that
intfdata will be NULL even if the drivers disconnect method does not properly
clear it. This ensures that intfdata will also be NULL after a failed probe,
even if the driver's probe method left a (likely dangling) pointer in there.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some composite USB devices provide multiple interfaces
with different functions, all using "vendor-specific"
for class/subclass/protocol.  Another OS use interface
numbers to match the driver and interface. It seems
these devices are designed with that in mind - using
static interface numbers for the different functions.

This adds support for matching against the
bInterfaceNumber, allowing such devices to be supported
without having to resort to testing against interface
number whitelists and/or blacklists in the probe.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There are several places where the USB core needs to disable USB 3.0
Link PM:
 - usb_bind_interface
 - usb_unbind_interface
 - usb_driver_claim_interface
 - usb_port_suspend/usb_port_resume
 - usb_reset_and_verify_device
 - usb_set_interface
 - usb_reset_configuration
 - usb_set_configuration

Use the new LPM disable/enable functions to temporarily disable LPM
around these critical sections.

We need to protect the critical section around binding and unbinding USB
interface drivers.  USB drivers may want to disable hub-initiated USB
3.0 LPM, which will change the value of the U1/U2 timeouts that the xHCI
driver will install.  We need to disable LPM completely until the driver
is bound to the interface, and the driver has a chance to enable
whatever alternate interface setting it needs in its probe routine.
Then re-enable USB3 LPM, and recalculate the U1/U2 timeout values.

We also need to disable LPM in usb_driver_claim_interface,
because drivers like usbfs can bind to an interface through that
function.  Note, there is no way currently for userspace drivers to
disable hub-initiated USB 3.0 LPM.  Revisit this later.

When a driver is unbound, the U1/U2 timeouts may change because we are
unbinding the last driver that needed hub-initiated USB 3.0 LPM to be
disabled.

USB LPM must be disabled when a USB device is going to be suspended.
The USB 3.0 spec does not define a state transition from U1 or U2 into
U3, so we need to bring the device into U0 by disabling LPM before we
can place it into U3.  Therefore, call usb_unlocked_disable_lpm() in
usb_port_suspend(), and call usb_unlocked_enable_lpm() in
usb_port_resume().  If the port suspend fails, make sure to re-enable
LPM by calling usb_unlocked_enable_lpm(), since usb_port_resume() will
not be called on a failed port suspend.

USB 3.0 devices lose their USB 3.0 LPM settings (including whether USB
device-initiated LPM is enabled) across device suspend.  Therefore,
disable LPM before the device will be reset in
usb_reset_and_verify_device(), and re-enable LPM after the reset is
complete and the configuration/alt settings are re-installed.

The calculated U1/U2 timeout values are heavily dependent on what USB
device endpoints are currently enabled.  When any of the enabled
endpoints on the device might change, due to a new configuration, or new
alternate interface setting, we need to first disable USB 3.0 LPM, add
or delete endpoints from the xHCI schedule, install the new interfaces
and alt settings, and then re-enable LPM.  Do this in usb_set_interface,
usb_reset_configuration, and usb_set_configuration.

Basically, there is a call to disable and then enable LPM in all
functions that lock the bandwidth_mutex.  One exception is
usb_disable_device, because the device is disconnecting or otherwise
going away, and we should not care about whether USB 3.0 LPM is enabled.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Keep the usb-serial support for dynamic IDs in sync with the usb
support.  This enables readout of dynamic device IDs for
usb-serial drivers.  Common code is exported from the usb core
system and reused by the usb-serial bus driver.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This enables the current list of dynamic IDs to be read out through
either new_id or remove_id.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This option has been deprecated for many years now, and no userspace
tools use it anymore, so it should be safe to finally remove it.
Reported-by: NKay Sievers <kay@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1532) fixes a mistake in the USB suspend code.  When the
system is going to sleep, we should ignore errors in powering down USB
devices, because they don't really matter.  The devices will go to low
power anyway when the entire USB bus gets suspended (except for
SuperSpeed devices; maybe they will need special treatment later).

However we should not ignore errors in suspending root hubs,
especially if the error indicates that the suspend raced with a wakeup
request.  Doing so might leave the bus powered on while the system was
supposed to be asleep, or it might cause the suspend of the root hub's
parent controller device to fail, or it might cause a wakeup request
to be ignored.

The patch fixes the problem by ignoring errors only when the device in
question is not a root hub.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NChen Peter <B29397@freescale.com>
CC: <stable@vger.kernel.org>
Tested-by: NChen Peter <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1514) cleans up some places where new_id and remove_id
sysfs attributes are created and deleted.  Handling both attributes in
a single routine rather than a pair of routines makes the code
smaller.  It also prevents certain kinds of errors, like one we
currently have in the USB subsystem: The removeid attribute is often
created even when newid isn't (because the driver's no_dynamid_id flag
is set).

In the case of the PCMCIA subsystem, the newid attribute is created
but never explicitly deleted.  The patch adds a deletion routine.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As part of the removal of get_driver()/put_driver(), this patch
(as1511) changes all the places that add dynamic IDs for drivers.
Since these additions are done by writing to the drivers' sysfs
attribute files, and the attributes are removed when the drivers are
unregistered, there is no reason to take an extra reference to the
drivers.

The one exception is the pci-stub driver, which calls pci_add_dynid()
as part of its registration.  But again, there's no reason to take an
extra reference here, because the driver can't be unloaded while it is
being registered.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This eliminates the last instance of a function's behavior
controlled by a parameter as Linus hates such things.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Do the cleanup to avoid behaviorial parameters Linus
requested.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If a driver does not support the suspend/resume callbacks
it will be forcibly disconnected. There is no reason to check
for support of the callbacks after that.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When adding the ID of a composite device dynamically to a driver, all
hitherto unbound interfaces are bound to this driver regardless of their
class, which may not be intended.
The patch adds the option to tell the targeted interface class to a driver
via the "new_id" attribute, in addition to the device ID.
Also, it appends the ABI documentation accordingly.

Example:
$ echo "1234 2a2a ff" >/sys/bus/usb-serial/drivers/option1/new_id
will bind only vendor-specific interfaces to the 3G driver.
Signed-off-by: NJosua Dietze <digidietze@draisberghof.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed.  The idle callback routine could
then schedule a delayed suspend for some time later.

However this behavior was changed by commit
f71648d7 (PM / Runtime: Remove idle
notification after failing suspend).  No notifications were sent, and
there was no clear mechanism to retry failed suspends.

This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down.  A companion
patch changes the PM core's behavior, but we also need to change the
USB core.  In particular, this patch (as1493) updates the device's
last_busy time when an autosuspend fails, so that the PM core will
retry the autosuspend in the future when the delay time expires
again.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NHenrik Rydberg <rydberg@euromail.se>
Cc: <stable@kernel.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.

Use the lightweight version of the header that has just THIS_MODULE
and EXPORT_SYMBOL variants.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

If the device pass the USB2 software LPM and the host supports hardware
LPM, enable hardware LPM for the device to let the host decide when to
put the link into lower power state.

If hardware LPM is enabled for a port and driver wants to put it into
suspend, it must first disable hardware LPM, resume the port into U0,
and then suspend the port.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A return value of -EINPROGRESS from pm_runtime_get indicates that
the device is already resuming due to a previous call.  Internally,
usb_autopm_get_interface_async doesn't treat this as an error and
increments the usage count, but passes the error status along
to the caller.  The logical assumption of the caller is that
any negative return value reflects the device not resuming
and the pm_usage_cnt not being incremented.  Since the usage count
is being incremented and the device is resuming, return success (0)
instead.
Signed-off-by: NJames Wylder <james.wylder@motorola.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1482) adds a macro for testing whether or not a
pm_message value represents an autosuspend or autoresume (i.e., a
runtime PM) event.  Encapsulating this notion seems preferable to
open-coding the test all over the place.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

This patch (as1473) renames the "in_suspend" field in struct
dev_pm_info to "is_prepared", in preparation for an upcoming change.
The new name is more descriptive of what the field really means.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org

This patch (as1464) implements the recommended policy that most errors
during suspend or hibernation should not prevent the system from going
to sleep.  In particular, failure to suspend a USB driver or a USB
device should not prevent the sleep from succeeding:

Failure to suspend a device won't matter, because the device will
automatically go into suspend mode when the USB bus stops carrying
packets.  (This might be less true for USB-3.0 devices, but let's not
worry about them now.)

Failure of a driver to suspend might lead to trouble later on when the
system wakes up, but it isn't sufficient reason to prevent the system
from going to sleep.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB defines usb_device_type pointing to usb_device_pm_ops that
provides system-wide PM callbacks only and usb_bus_type pointing to
usb_bus_pm_ops that provides runtime PM callbacks only.  However,
the USB runtime PM callbacks may be defined in usb_device_pm_ops
which makes it possible to drop usb_bus_pm_ops and will allow us
to consolidate the handling of subsystems by the PM core code.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

The PM core reacts badly when the return code from usb_runtime_suspend()
is not 0, -EAGAIN, or -EBUSY.  The PM core regards this as a fatal error,
and refuses to run anymore PM helper functions.  In particular,
usbfs_open() and other usbfs functions will fail because the PM core will
return an error code when usb_autoresume_device() is called.  This causes
libusb and/or lsusb to either hang or segfault.

If a USB device cannot suspend for some reason (e.g. a hub doesn't report
it has remote wakeup capabilities), we still want lsusb and other
userspace programs to work.  So return -EBUSY, which will fill people's
log files with failed tries, but will ensure userspace still works.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The device power.status field is too complicated for its purpose
(storing the information about whether or not the device is in the
"active" state from the PM core's point of view), so replace it with
a bit field and modify all of its users accordingly.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

This patch (as1434) cleans up the uses of usb_mark_last_busy() in
usbcore.  The function will be called when a device is resumed and
whenever a usage count is decremented.  A call that was missing from
the hub driver is added: A hub is used whenever one of its ports gets
suspended (this prevents hubs from suspending immediately after their
last child).

In addition, the call to disable autosuspend support for new devices
by default is moved from usb_detect_quirks() (where it doesn't really
belong) into usb_new_device() along with all the other runtime-PM
initializations.  Finally, an extra pm_runtime_get_noresume() is added
to prevent new devices from autosuspending while they are being
registered.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1428) converts USB over to the new runtime-PM core
autosuspend framework.  One slightly awkward aspect of the conversion
is that USB devices will now have two suspend-delay attributes: the
old power/autosuspend file and the new power/autosuspend_delay_ms
file.  One expresses the delay time in seconds and the other in
milliseconds, but otherwise they do the same thing.  The old attribute
can be deprecated and then removed eventually.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since the runtime-PM core already defines a .last_busy field in
device.power, this patch uses it to replace the .last_busy field
defined in usb_device and uses pm_runtime_mark_last_busy to implement
usb_mark_last_busy.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Reviewed-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Call pm_runtime_no_callbacks to set no_callbacks flag for USB
interfaces.  Since interfaces cannot be power-managed separately from
their parent devices, there's no reason for the runtime-PM core to
invoke any callbacks for them.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Reviewed-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

At otg device mode, the otg host resume should do no-op during
system resume, otherwise, the otg device will be treated as a
host for enumeration.

So, the otg host driver returns -ESHUTDOWN if it detects the
current usb mode is device mode. The host driver has to return
-ESHUTDOWN, otherwise, the usb_hc_died will be called.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fake "address-of" expressions that evaluate to NULL generally confuse
readers and can provoke compiler warnings.  This patch (as1412)
removes three such fake expressions, using "#ifdef"s in their place.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixed coding styles in the core usb driver.
Signed-off-by: NCarlos Sánchez Acosta <csanchez@neurowork.net>
Signed-off-by: NAlejandro Sánchez Acosta <asanchez@neurowork.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1403) is a partial reversion of an earlier change
(commit 5f677f1d "USB: fix remote
wakeup settings during system sleep").  After hearing from a user, I
realized that remote wakeup should be enabled during system sleep
whenever userspace allows it, and not only if a driver requests it
too.

Indeed, there could be a device with no driver, that does nothing but
generate a wakeup request when the user presses a button.  Such a
device should be allowed to do its job.

The problem fixed by the earlier patch -- device generating a wakeup
request for no reason, causing system suspend to abort -- was also
addressed by a later patch ("USB: don't enable remote wakeup by
default", accepted but not yet merged into mainline).  The device
won't be able to generate the bogus wakeup requests because it will be
disabled for remote wakeup by default.  Hence this reversion will not
re-introduce any old problems.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1387) fixes a bug introduced during the changeover to
the runtime PM framework.  When a driver doesn't support resume or
reset-resume, and consequently its interfaces need to be unbound and
rebound, we have to unbind all the interfaces before trying to rebind
any of them.  Otherwise the driver's probe method for one interface
could try to claim a different interface and fail, because that other
interface hasn't been unbound yet.

This fixes Bugzilla #15788.  The symptom is that some USB sound cards
don't work after hibernation.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NFrançois Valenduc <francois.valenduc@tvcablenet.be>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1379) reworks the logic for handling USB interface
runtime-PM settings -- hopefully it's right this time!  The problem is
that when a driver is unbound or binding fails, runtime PM for the
interface always gets disabled.  But pm_runtime_disable() nests, so it
shouldn't be called unless the interface was previously enabled for
runtime PM.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NRob Duncan <Robert.Duncan@exar.com>
Tested-by: NRob Duncan <Robert.Duncan@exar.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1366) replaces the private routines
usb_enable_autosuspend() and usb_disable_autosuspend() with calls to
the standard pm_runtime_allow() and pm_runtime_forbid() functions in
the runtime PM framework.  They do the same thing.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1362) adjusts the way the USB autosuspend routines
handle remote-wakeup settings.  They aren't supposed to use
device_may_wakeup(); that test is intended only for system sleep, not
runtime power management.  Instead the code checks to see if any
interface drivers need remote wakeup; if they do then it is enabled,
provided the device is capable of it.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hcd.h from drivers/usb/core into include/linux/usb/
Signed-of-by: NEric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1370) fixes a bug in the USB runtime power management
code.  When a driver claims an interface, it doesn't expect to need to
call usb_autopm_get_interface() or usb_autopm_put_interface() for
runtime PM to work.  Runtime PM can be controlled by the driver's
primary interface; the additional interfaces it claims shouldn't
interfere.  As things stand, the claimed interfaces will prevent the
device from autosuspending.

To fix this problem, the patch sets interfaces to the suspended state
when they are claimed.

Also, although in theory this shouldn't matter, the patch changes the
suspend code so that interfaces are suspended in reverse order from
detection and resuming.  This is how the PM core works, and we ought
to use the same approach.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Debugged-and-tested-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1363) changes the way USB remote wakeup is handled
during system sleeps.  It won't be enabled unless an interface driver
specifically needs it.  Also, it won't be enabled during the FREEZE or
QUIESCE phases of hibernation, when the system doesn't respond to
wakeup events anyway.  Finally, if the device is already
runtime-suspended with remote wakeup enabled, but wakeup is supposed
to be disabled for the system sleep, the device gets woken up so that
it can be suspended again with the proper wakeup setting.

This will fix problems people have reported with certain USB webcams
that generate wakeup requests when they shouldn't, and as a result
cause system suspends to fail.  See

	https://bugs.launchpad.net/ubuntu/+source/linux/+bug/515109Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NErik Andrén <erik.andren@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>