As pointed out by Ben Hutchings drivers that allow using VLAN have to
provide enough headroom for the VLAN tags.
Signed-off-by: NAlban Bedel <albeu@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver allows MTU up to 1518 bytes which is not enought to run
batman-adv. Simply raise the maximum packet size up to the maximum
allowed by the transmit descriptor, 1792 bytes, giving a maximum MTU
of 1774 bytes.
Signed-off-by: NAlban Bedel <albeu@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the default ndo_change_mtu callback with one that allow
setting MTU that the driver can handle.
Signed-off-by: NAlban Bedel <albeu@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several warnings and errors of coding style rules corrected.
Compile tested.
Signed-off-by: NRoberto Medina <robertoxmed@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8168EP is Realtek PCIe Gigabit Ethernet controller with DASH support.
It is a successor chip of RTL8168DP.

For RTL8168EP, the read/write ocp register is via eri channel type 2, so I
move ocp_xxx() related functions under rtl_eri_xxx. And use r8168dp_ocp_xxx()
for RTL8168DP ocp read/write, r8168ep_ocp_xxx() for RTL8168EP ocp read/write.

The way of checking dash enable is different with RTL8168DP. I use
r8168dp_check_dash()for RTL8168DP and r8168ep_check_dash() for RTL8168EP,
to check if dash is enabled.

The driver_start() and driver_stop() of RTL8168EP is also different with
RTL8168DP. I use rtl8168dp_driver_xxx() for RTL8168DP and
rtl8168ep_driver_xxx for RTL8168EP.

Right now, RTL8168EP phy mcu did not need firmware code patch, so I did not
add firmware code for it.
so I did not add firmware code for it.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tested on RTL8168d/8111d model using 'super_netperf 40' with TCP/UDP_STREAM.

Output of
while true; do
    for n in inflight limit; do
          echo -n $n\ ; cat $n;
    done;
    sleep 1;
done

during netperf run, 100mbit peer:

inflight 0
limit 3028
inflight 6056
limit 4542

[ trimmed output for brevity, no limit/inflight changes during
  test steady-state ]

limit 4542
inflight 3028
limit 6122
inflight 0
limit 6122
[ changed cable to 1gbit peer, restart netperf ]
inflight 37850
limit 36336
inflight 33308
limit 31794
inflight 33308
limit 31794
inflight 27252
limit 25738
[ again, no changes during test ]
inflight 27252
limit 25738
inflight 0
limit 28766
[ change cable to 100mbit peer, restart netperf ]
limit 28766
inflight 27370
limit 28766
inflight 4542
limit 5990
inflight 6056
limit 4542
[ .. ]
inflight 6056
limit 4542
inflight 0

[end of test]

Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Acked-by: NEric Dumazet <edumazet@google.com>
Acked-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These two functions are used to inform dash firmware that driver is been
brought up or brought down. So call these two functions only when hardware dash
function is enabled.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function "rtl8168_oob_notify", using function "rtl_eri_write" to access
eri register 0xe8, instead of using MAC register "ERIDR" and "ERIAR" to
access it.

For using function "rtl_eri_write" in function "rtl8168_oob_notify", need to
move down "rtl8168_oob_notify" related functions under the function
"rtl_eri_write".
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DASH function not only RTL8168DP can support, but also RTL8168EP.
So change the name of function "r8168dp_check_dash" to "r8168_check_dash".
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the name of function "rtl_w1w0_eri" to "rtl_w0w1_eri".

In this function, the local variable "val" is "write zeros then write ones".
Please see below code.

(val & ~m) | p

In this patch, change the function name from "xx_w1w0_xx" to "xx_w0w1_xx".
The changed function name is more suitable for it's behavior.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change function name from "rtl_w1w0_phy" to "rtl_w0w1_phy".
And its behavior from "write ones then write zeros" to
"write zeros then write ones".

In Realtek internal driver, bitwise operations are almost "write zeros then
write ones". For easy to port hardware parameters from Realtek internal driver
to Linux kernal driver "r8169", we would like to change this function's
behavior and its name.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For RTL8168F RTL8168FB RTL8168G RTL8168GU RTL8411 RTL8411B RTL8402 RTL8107E,
the magic packet enable bit is changed to eri 0xde bit0.

In this patch, change magic packet enable bit of these chips to eri 0xde bit0.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8168FB RTL8168G RTL8168GU RTL8411 RTL8411B RTL8106EUS RTL8402 can
support get mac address from backup mac address register.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8411B can support disable/enable pll function.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8168G also can disable/enable pll function.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an extra semi-colon so __rtl8169_set_features() is called every
time.

Fixes: 929a031d ('r8169: adjust __rtl8169_set_features')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>--
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the "changed" test in __rtl8169_set_features(). Instead, do
simple test in rtl8169_set_features().

Set the RxChkSum and RxVlan through __rtl8169_set_features() in
rtl_open().
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The setting should depend on the new features not the current one.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the parameter "features" of __rtl8169_set_features() is equal to
dev->features, the variable "changed" is alwayes 0, and nothing would
be changed.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Leftover from 6e1d0b89 ("r8169:add
support for RTL8168H and RTL8107E").
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8168H is Realtek PCIe Gigabit Ethernet controller.
RTL8107E is Realtek PCIe Fast Ethernet controller.

This patch add support for these two chips.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines.  This issue was reported by checkpatch.

A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):

// <smpl>

@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@

- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;

// </smpl>

[bhelgaas: add semantic patch]
Signed-off-by: NBenoit Taine <benoit.taine@lip6.fr>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

This patch use the struct pci_device_id instead of using macro
DEFINE_PCI_DEVICE_TABLE which is deprecated and should not be used.
And also moves these ids after probe and remove functionalities.
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts to use the macro module_pci_driver, which makes
the code smaller and simpler.

Previously in this driver we are having driver version info will be
printed log buffer based on whether the driver selected as module
or statically into image itself. By using the module_pci_driver that
part of the code removed. For the first time of the device init,
we are making the version info to be printed once.
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethernet port on my ASUS A88X Pro mainboard stopped working
several times a day, with messages like these in dmesg:

AMD-Vi: Event logged [IO_PAGE_FAULT device=05:00.0 domain=0x001e address=0x0000000000003000 flags=0x0050]

Searching the web for these messages led me to similar reports about
different hardware supported by r8169, and eventually to commits
3ced8c95 ('r8169: enforce RX_MULTI_EN
for the 8168f.') and eb2dc35d ('r8169:
RxConfig hack for the 8168evl'). So I tried this change, and it fixes
the problem for me.
Signed-off-by: NMichel Dänzer <michel@daenzer.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support the IPv6 hw checksum for RTL8111C and later chips. Note
that the hw has the limitation for the transport offset. The
checksum must be calculated by sw, when the transport offset is
out of the range which the hw accepts.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace large send with giant send for TSO for RTL8111C and later ICs.
The large send setting of the RTL8111DP is different from the other
chips. However, the giant send setting is the same for all the chips
which support it. Use the giant send to synchronize the settings.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the txd_version, split rtl8169_tso_csum() into
rtl8169_tso_csum_v1() and rtl8169_tso_csum_v2().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For RTL8411, RTL8111G, RTL8402, RTL8105, and RTL8106, disable the feature
of entering the L2/L3 link state of the PCIe. When the nic starts the process
of entering the L2/L3 link state and the PCI reset occurs before the work
is finished, the work would be queued and continue after the next the PCI
reset occurs. This causes the device stays in L2/L3 link state, and the system
couldn't find the device.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: get rid of SET_ETHTOOL_OPS

Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.

Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
-       SET_ETHTOOL_OPS(dev, ops);
+       dev->ethtool_ops = ops;

Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: NDave Miller <davem@davemloft.net>
Signed-off-by: NWilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the bh safe variant with the hard irq safe variant.

We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.

Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace kfree_skb with dev_kfree_skb_any in cp_start_xmit
as it can be called in both hard irq and other contexts.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tx descriptor version of RTL8111B belong to RTL_TD_0.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Boris reports he's seeing:
> [    9.195943] INFO: trying to register non-static key.
> [    9.196031] the code is fine but needs lockdep annotation.
> [    9.196031] turning off the locking correctness validator.
> [    9.196031] CPU: 1 PID: 933 Comm: modprobe Not tainted 3.14.0-rc4+ #1
with the r8169 driver.

These are occuring because the seqcount embedded in u64_stats_sync on
32-bit SMP is uninitialized which is making lockdep unhappy.
Signed-off-by: NKyle McMartin <kyle@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.   Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using iperf to send packets(GSO mode is on), a bug is triggered:

[  212.672781] kernel BUG at lib/dynamic_queue_limits.c:26!
[  212.673396] invalid opcode: 0000 [#1] SMP
[  212.673882] Modules linked in: 8139cp(O) nls_utf8 edd fuse loop dm_mod ipv6 i2c_piix4 8139too i2c_core intel_agp joydev pcspkr hid_generic intel_gtt floppy sr_mod mii button sg cdrom ext3 jbd mbcache usbhid hid uhci_hcd ehci_hcd usbcore sd_mod usb_common crc_t10dif crct10dif_common processor thermal_sys hwmon scsi_dh_emc scsi_dh_rdac scsi_dh_hp_sw scsi_dh ata_generic ata_piix libata scsi_mod [last unloaded: 8139cp]
[  212.676084] CPU: 0 PID: 4124 Comm: iperf Tainted: G           O 3.12.0-0.7-default+ #16
[  212.676084] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[  212.676084] task: ffff8800d83966c0 ti: ffff8800db4c8000 task.ti: ffff8800db4c8000
[  212.676084] RIP: 0010:[<ffffffff8122e23f>]  [<ffffffff8122e23f>] dql_completed+0x17f/0x190
[  212.676084] RSP: 0018:ffff880116e03e30  EFLAGS: 00010083
[  212.676084] RAX: 00000000000005ea RBX: 0000000000000f7c RCX: 0000000000000002
[  212.676084] RDX: ffff880111dd0dc0 RSI: 0000000000000bd4 RDI: ffff8800db6ffcc0
[  212.676084] RBP: ffff880116e03e48 R08: 0000000000000992 R09: 0000000000000000
[  212.676084] R10: ffffffff8181e400 R11: 0000000000000004 R12: 000000000000000f
[  212.676084] R13: ffff8800d94ec840 R14: ffff8800db440c80 R15: 000000000000000e
[  212.676084] FS:  00007f6685a3c700(0000) GS:ffff880116e00000(0000) knlGS:0000000000000000
[  212.676084] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  212.676084] CR2: 00007f6685ad6460 CR3: 00000000db714000 CR4: 00000000000006f0
[  212.676084] Stack:
[  212.676084]  ffff8800db6ffc00 000000000000000f ffff8800d94ec840 ffff880116e03eb8
[  212.676084]  ffffffffa041509f ffff880116e03e88 0000000f16e03e88 ffff8800d94ec000
[  212.676084]  00000bd400059858 000000050000000f ffffffff81094c36 ffff880116e03eb8
[  212.676084] Call Trace:
[  212.676084]  <IRQ>
[  212.676084]  [<ffffffffa041509f>] cp_interrupt+0x4ef/0x590 [8139cp]
[  212.676084]  [<ffffffff81094c36>] ? ktime_get+0x56/0xd0
[  212.676084]  [<ffffffff8108cf73>] handle_irq_event_percpu+0x53/0x170
[  212.676084]  [<ffffffff8108d0cc>] handle_irq_event+0x3c/0x60
[  212.676084]  [<ffffffff8108fdb5>] handle_fasteoi_irq+0x55/0xf0
[  212.676084]  [<ffffffff810045df>] handle_irq+0x1f/0x30
[  212.676084]  [<ffffffff81003c8b>] do_IRQ+0x5b/0xe0
[  212.676084]  [<ffffffff8142beaa>] common_interrupt+0x6a/0x6a
[  212.676084]  <EOI>
[  212.676084]  [<ffffffffa0416a21>] ? cp_start_xmit+0x621/0x97c [8139cp]
[  212.676084]  [<ffffffffa0416a09>] ? cp_start_xmit+0x609/0x97c [8139cp]
[  212.676084]  [<ffffffff81378ed9>] dev_hard_start_xmit+0x2c9/0x550
[  212.676084]  [<ffffffff813960a9>] sch_direct_xmit+0x179/0x1d0
[  212.676084]  [<ffffffff813793f3>] dev_queue_xmit+0x293/0x440
[  212.676084]  [<ffffffff813b0e46>] ip_finish_output+0x236/0x450
[  212.676084]  [<ffffffff810e59e7>] ? __alloc_pages_nodemask+0x187/0xb10
[  212.676084]  [<ffffffff813b10e8>] ip_output+0x88/0x90
[  212.676084]  [<ffffffff813afa64>] ip_local_out+0x24/0x30
[  212.676084]  [<ffffffff813aff0d>] ip_queue_xmit+0x14d/0x3e0
[  212.676084]  [<ffffffff813c6fd1>] tcp_transmit_skb+0x501/0x840
[  212.676084]  [<ffffffff813c8323>] tcp_write_xmit+0x1e3/0xb20
[  212.676084]  [<ffffffff81363237>] ? skb_page_frag_refill+0x87/0xd0
[  212.676084]  [<ffffffff813c8c8b>] tcp_push_one+0x2b/0x40
[  212.676084]  [<ffffffff813bb7e6>] tcp_sendmsg+0x926/0xc90
[  212.676084]  [<ffffffff813e1d21>] inet_sendmsg+0x61/0xc0
[  212.676084]  [<ffffffff8135e861>] sock_aio_write+0x101/0x120
[  212.676084]  [<ffffffff81107cf1>] ? vma_adjust+0x2e1/0x5d0
[  212.676084]  [<ffffffff812163e0>] ? timerqueue_add+0x60/0xb0
[  212.676084]  [<ffffffff81130b60>] do_sync_write+0x60/0x90
[  212.676084]  [<ffffffff81130d44>] ? rw_verify_area+0x54/0xf0
[  212.676084]  [<ffffffff81130f66>] vfs_write+0x186/0x190
[  212.676084]  [<ffffffff811317fd>] SyS_write+0x5d/0xa0
[  212.676084]  [<ffffffff814321e2>] system_call_fastpath+0x16/0x1b
[  212.676084] Code: ca 41 89 dc 41 29 cc 45 31 db 29 c2 41 89 c5 89 d0 45 29 c5 f7 d0 c1 e8 1f e9 43 ff ff ff 66 0f 1f 44 00 00 31 c0 e9 7b ff ff ff <0f> 0b eb fe 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 c7 47 40 00
[  212.676084] RIP  [<ffffffff8122e23f>] dql_completed+0x17f/0x190
------------[ cut here ]------------

When a skb has frags, bytes_compl plus skb->len nr_frags times in cp_tx().
It's not the correct value(actually, it should plus skb->len once) and it
will trigger the BUG_ON(bytes_compl > num_queued - dql->num_completed).
So only increase bytes_compl when finish sending all frags. pkts_compl also
has a wrong value, fix it too.

It's introduced by commit 871f0d4c ("8139cp: enable bql").
Suggested-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>