The firmware supports a maximum of 4K FCoE exchanges. In 4-port devices,
or when working in multi-function mode, this resource needs to be distributed
between the various possible FCoE functions.

This information needs to be calculated by bnx2x and propagated into bnx2fc
via cnic. bnx2fc can then use this value to calculate corresponding xid
resources instead of using global constants.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enables hardware generation of IP header and
protocol specific checksums for transmitted
packets.

Enabled hardware discarding of received packets with
invalid IP header or protocol specific checksums.

The feature is enabled by default but can be
enabled/disabled by ethtool.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NJim Baxter <jim_baxter@mentor.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "changed" variable should be a 64 bit type, otherwise it can't store
all the features.  The way the code is now the test for whether
NETIF_F_RXCSUM changed is always false and we return immediately.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes id defines from the hardware files that will not be
productized for Linux.  These id's were not implemented for support in the
base driver itself, they were just available defines.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The 82575 manual initialization scripts are not supported on 82580 and
above. Rather than call the function to immediately return, clarify the
code by removing this pointless function call.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When using the new bridge FDB interface to allow SR-IOV virtual function
network devices to communicate with SW bridged network devices the
physical function is placed into promiscuous mode and hardware VLAN
filtering is disabled.  This defeats the ability to use VLAN tagging
to isolate user networks.  When the device is in promiscuous mode and
VT mode simultaneously ensure that VLAN hardware filtering remains
enabled.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Current igb driver doesn't tell nothing when Link Speed is downgraded due to
SmartSpeed.  As a result, users suspect that there is something wrong with
NIC.  If the cause of it is SmartSpeed, there is no means to replace NIC. This
patch make igb notify users that SmartSpeed worked.
Signed-off-by: NKoki Sanagi <sanagi.koki@jp.fujitsu.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that the igb driver uses the generic helper
pci_vfs_assigned instead of the igb specific function igb_vfs_are_assigned.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It was previously thought that, since I210/I211 are single port devices,
they did not need the SMBI semaphore. This is not the case. Add support for
the SMBI semaphore.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements SERDES loopback configuration for i210 devices by
unsetting sigdetect bit, so as to fix Ethtool loopback test failure. Old
sigdetect code is also simplified to take care of all devices newer than 82580
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a define and WOL support for a new subdevice ID.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds LX support to 82599 devices. This is an alternate patch to
the one suggested by Stefan Behte <s.behte@babiel.com>

In addition this patch includes some cleanups such as:
- removed parenthesis around "x == y ||" lines inside an if statement for
consistency.
- grouped the sx/lx sfp types along with srlr in ixgbe_get_settings() since
they all have the same supported, advertised and port values.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Reported-by: NStefan Behte <s.behte@babiel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The variable wol_supported really is just checking whether it is enabled, rather
than whether it is supported. If it is enabled it will be supported, but this
does not necessarily hold true the other way around. This patch renames the
variable to avoid confusion.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for the new OCP x520 adapter.  This support
includes WoL.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Protect the code by bailing out of ixgbe_update_itr() when this occurs.
The next call to ixgbe_update_itr will continue to dynamically update ITR.
Signed-of-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Added identifying strings for 8300 Series of adapters.
o updated PCI_VENDOR_ID_QLOGIC and PCI_DEVICE_ID_824X for 8200
  Series adapter.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Here's what modified vectors will look like
in the /proc/interrupts

        MSIx             	INTx
-----------------------------------------
83xx    qlcnic[MB]
	qlcnic-ethX[Rx0]
	qlcnic-ethX[Rx1]
	..
	qlcnic-ethX[RxN]
	qlcnic-ethx[Tx0]        qlcnic[MB+Tx0+Rx0]

82xx    qlcnic-ethX[Rx0]
	qlcnic-ethX[Rx1]
	..
	qlcnic-ethX[Tx0+RxN]    qlcnic-ethX[Tx0+Rx0]
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable Interrupt coalescing through ethtool on 83xx adapter.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Read eSwitch statistics from adapter and display them as part
  of ethtool statistics.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Disabling PAUSE requires access to EPORT registers,
  which may cause a wedge, if EPORT is in reset.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Add logs for various failure conditions during channel configuration.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of PCIe Advanced Error Reporting flow, if a fatal PCI error occurs,
the AER driver will cause bnx2x's PCI-core to reset. The driver's PCI error
handlers will in turn restore the PCI configuration space values by calling
`pci_restore_state'.

However, as bnx2x does not save the PCI configuration after restoration,
An additional fatal PCI error will leave the function in an unstable state
until reboot, as the registers in the PCI configuration space will contain
reset values.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There exists an `allocation race' between the CNIC and bnx2x drivers,
in which both drivers allocate the same t2 memory while disregarding a possible
previous allocation.

Additionally, due to the current order of memory releases, some of the
ILT memory in the driver is not released correctly when unloading the driver.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improved support for adding/removing vf mac addresses.

This includes the case where HyperVisor forced the address (sampled from
bulletin board), and the case where it did not in which the VF can
configure its own mac address.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, when link is configured to auto-negotiate the flow control,
disabling RX/TX pause via ethtool doesn't work.

This fixes the behaviour, advertising asymmetric pause in case either one
is exclusively enabled.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces a more robust error handling flow in case of incorrect
behaviour by the FW when passing on GRO aggregations.

Although this should never happen (i.e., this is merely a theoretical fix),
if the bnx2x driver was to receive a GRO from FW with protocol other than
IPv4/IPv6, the driver would falsely claim to have performed partial
checksum and set various incorrect fields in the skb header.

Current behaviour of the bnx2x driver (i.e., print an error) is insufficient.
This patch remedies this by simply preventing the false claims.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a service task to run tasks that needed to be executed periodically.
Currently the only task is a watchdog to catch NIC clock overflow, to make
timestamping accurate.
Will move the statistics task into this framework in a later patch.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kernel software timestamping requires that the driver calls skb_tx_timestamp
just before passing the skb to the HW MAC layer. This patch adds this call.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch allows to enable/disable HW timestamping for incoming and/or
outgoing packets. It adds and initializes all structs and callbacks
needed by kernel TS API.
To enable/disable HW timestamping appropriate ioctl should be used.
Currently HWTSTAMP_FILTER_ALL/NONE and HWTSAMP_TX_ON/OFF only are
supported.
When enabling TS on receive flow - VLAN stripping will be disabled.
Also were made all relevant changes in RX/TX flows to consider TS request
and plant HW timestamps into relevant structures.
mlx4_ib was fixed to compile with new mlx4_cq_alloc() signature.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Read HCA frequency, read PCI clock bar and offset, map internal clock to
PCI bar.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new device capability for timestamping support and query FW to retrieve it.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rotate bss prio list, so the bss next to the one served, will come first
in the list of bss' with equal priority. This way we pick bss nodes in a
round robin fashion. Using list rotation instead of a cur ptr simplifies
iteration to calling list_for_each_entry. List rotation is done via
list_move, where the head itself is temporarily removed and then
re-inserted after the bss just served.
Signed-off-by: NAndreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After a packet is successfully transmitted, ra list is rotated, so the ra
next to the one transmitted, will be the first in the list. This way we
pick the ra' in a round robin fashion. This significantly simplifies
iteration in  mwifiex_wmm_get_highest_priolist_ptr to a call to
list_for_each_entry.
List rotation is done via list_move, where the head itself is temporarily
removed and then re-inserted after the item just transferred.
Signed-off-by: NAndreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware provides credits to the driver per WMM-AC. When
only AC_BE are to be transmitted to the firmware the driver
may use credits from other priorities to send AC_BE packets
towards the firmware.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In brcmf_fws_init() the error flows were not properly handled
and the caller ignored the return value. The only action that
is allowed to fail in brcmf_fws_init() is setting the tlv in
firmware as the feature is not supported on all devices.

Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When firmware signals the driver to remove a destination entry
it may have sk_buff packets queued for it. These should be freed.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adds support for the critical protocol API provided by nl80211
which gives Wifi traffic priority over a Bluetooth (e)SCO connection
and disables scanning during DCHP negotiation.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During the DHCP protocol exchange it is benificial to suppress
scan requests which may decrease time to complete DHCP protocol.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>