Rockchip SoCs contain clocks tightly bound to the armclk, where the best
rate / divider is supplied by the vendor after careful measuring.
Often this ideal rate may be greater than the current rate.

Therefore prevent the ccf from trying to set these dividers itself by
setting them to read-only.

In the case of the rk3066, this also includes the aclk_cpu, which makes it
necessary to also split its direct child-clocks (pclk_cpu, hclk_cpu, ...)
into individual definitions for rk3066 and rk3188.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>

aclk_cpu_pre on the rk3188 can either be sourced from the armclk or the gpll.
To reduce complexity on apll changes caused by cpufreq, reparent it always
to the gpll source.

If really necessary it could be reparented back on a per board level using
the assigned-clocks mechanism.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

In RK3288, APLL lock status bit is in GRF_SOC_STATUS1,
but in RK3188, is GRFSOC_STATUS0.
Signed-off-by: NJianqun <jay.xu@rock-chips.com>

Also name the constant accordingly as GRF_SOC_STATUS1
to prevent confusion.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>

The register providing the pll lock status is at a different address on the
rk3066. The error became apparent while working on cpufreq support for
the rockchip SoCs.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The Rockchip PLL code switches into slow mode (AKA bypass more AKA
24MHz mode) before actually changing the PLL.  This keeps anyone from
using the PLL while it's changing.  However, in all known Rockchip
SoCs nobody should ever see the 24MHz when changing the PLL supplying
the armclk because we should reparent children to an alternate
(faster than 24MHz) PLL.

One problem is that the code to switch to an alternate parent was
running in PRE_RATE_CHANGE.  ...and the code to switch to slow mode
was _also_ running in PRE_RATE_CHANGE.  That meant there was no real
guarantee that we would switch to an alternate parent before switching
to 24MHz mode.

Let's move the switch to "slow mode" straight into
rockchip_rk3066_pll_set_rate().  That means we're guaranteed that the
24MHz is really a last-resort.

Note that without this change on real systems we were the code to
switch to an alternate parent at 24MHz.  In some older versions of
that code we'd appy a (temporary) / 5 to the 24MHz causing us to run
at 4.8MHz.  That wasn't enough to service USB interrupts in some cases
and could lead to a system hang.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This patch add the clock node in PD_VIDEO
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Reviewed-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This patch use the new defined clock ID to initial the clock nodes.
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The npll on rk3288 is exactly the same pll type as the other 4. Yet it
was missing the link to the rate table, making rate changes impossible.
Change that by setting the table.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NKever Yang <kever.yang@rock-chips.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The rk3288 actually has 12 softresets, so fix the register count.
Signed-off-by: NMark yao <mark.yao@rock-chips.com>
Reviewed-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The dwc2 usb controller also uses agressive clock gating, which in this
case leads to hclk_peri getting disabled and hanging the system.
Therefore move it to the critical clocks until we also control that
part of the system.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The clocks for i2c1 and i2c2 are flipped.  The clock tree matched the
Technical Reference Manual (TRM) but the TRM was wrong.  Swap them in
the clock tree.  This was determined experimentally (by Addy) and
confirmed by the Rockchip IC team.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reported-by: NAddy Ke <addy.ke@rock-chips.com>
Reviewed-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The clock-tree contains clocks that should never get disabled automatically.
One example are the base ACLKs, the base supplies for all peripherals.

Therefore add a structure similar to the sunxi clock-tree to protect these
special clocks from being disabled.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NKever Yang <kever.yang@rock-chips.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

It is only used locally in clk/rockchip/clk.c and thus can be static.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Rockchip SoCs may provide fraction dividers for some clocks, mostly for
i2s and uarts. In contrast to the other registers, these do not use
the hiword-mask paradigm, but instead split the register into the upper
16 bit for the nominator and the lower 16 bit for the denominator.

The common clock framework got a generic fractional divider clock type
recently that can accomodate this setting easily. All currently known
fraction dividers have a separate gate too, therefore implement the
divider as composite using the ops-struct from fractional_divider clock
and add the gate if necessary.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add the clock tree definition for the new rk3288 SoC.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This adds a clock driver that handles the specific muxes, dividers and gates
of rk3188 and rk3066 SoCs.

The structure of the clock list resembles the arrangement of their
counterparts in the clock architecture diagrams found in the SoC
documentation.

Clocks exported to the clock provider are currently limited to well known
or measured ones. So additional clock exports may be necessary in the future.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

All Rockchip SoCs at least down to the ARM9-based RK28xx include the reset-
controller for SoC peripherals in their clock controller.
While the older SoCs (ARM9 and Cortex-A8) use a regular scheme to change
register values, the Cortex-A9 SoCs use a hiword-mask making locking unecessary.
To be compatible with both schemes the reset controller takes a flag to
decide which scheme to use, similar to the other HIWORD_MASK flags used in the
clock framework.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

All known Rockchip SoCs down to the RK28xx (ARM9) use a similar pattern to
handle their plls:
                       |--\
xin32k ----------------|mux\
xin24m -----| pll |----|pll|--- pll output
       \---------------|src/
                       |--/

The pll output is sourced from 1 of 3 sources, the actual pll being one of
them. To change the pll frequency it is imperative to remux it to another
source beforehand. This is done by adding a clock-listener to the pll that
handles the remuxing before and after the rate change.

The output mux is implemented as a separate clock to make use of already
existing common-clock features for disabling the pll if one of the other
two sources is used.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This adds infrastructure for registering clock branches. On Rockchip SoCs
most clock branches are a combination of mux,divider and gate components,
thus a composite clock is used when appropriate.

Clock branches are supposed to be declared in an array using the COMPOSITE*
or MUX, etc makros defined in the header and then registered using
rockchip_clk_register_branches.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Adding function type checking to CLK_OF_DECLARE found a type mismatch with
rk2928_gate_clk_init. The function only takes a single struct device_node
parameter.
Signed-off-by: NRob Herring <robh@kernel.org>
Acked-by: NMike Turquette <mturquette@linaro.org>

This adds basic support for gate-clocks on Rockchip SoCs.
There are 16 gates in each register and use the HIWORD_MASK
mechanism for changing gate settings.

The gate registers form a continuos block which makes the dt node
structure a matter of taste, as either all 160 gates can be put into
one gate clock spanning all registers or they can be divided into
the 10 individual gates containing 16 clocks each.
The code supports both approaches.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>