Use GPIO support by adding SD card detection configuration and
GPIO pinmux for Colibri's standard GPIO pins. Attach the GPIO
pins to the iomuxc node to get the GPIO pin settings applied.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Audio on phyFLEX boards is presented by tlv320aic3007 codec connected
over SSI interface.
Signed-off-by: NDmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Since pins and frequency are specific to module (pfla02), not base board
(pbab02), it is better to be initialized in corresponding dts file.

This patch fixes i2c2, i2c3 pin configuration which caused messages:

imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c2grp
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c3grp
imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c2grp
imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c3grp
Signed-off-by: NDmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add Colibri VF50 device tree files vf500-colibri.dtsi and
vf500-colibri-eval-v3.dts, in line with the Colibri VF61 device tree
files. However, to minimize dupplication we also add vf-colibri.dtsi
and vf-colibri-eval-v3.dtsi which contain the common device tree
nodes.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This adds more generic base device trees for Vybrid SoCs. There
are three series of Vybrid SoC commonly available:
- VF3xx series: single core, Cortex-A5 without external memory
- VF5xx series: single core, Cortex-A5
- VF6xx series: dual core, Cortex-A5/Cortex-M4

The second digit represents the presents of a L2 cache (VFx1x).

The VF3xx series are not suitable for Linux especially since the
internal memory is quite small (1.5MiB).

The VF500 is essentially the base SoC, with only one core and
without L1 cache. The VF610 is a superset of the VF500, hence
vf500.dtsi is then included and enhanced by vf610.dtsi. There is
no board using VF510 or VF600 currently, but, if needed, they can
be added easily.

The Linux kernel can also run on the Cortex-M4 CPU of Vybrid
using !MMU support. This patchset creates a device tree structure
which allows to share peripherals nodes for a VF6xx Cortex-M4
device tree too. The two CPU types have different views of the
system: Foremost they are using different interrupt controllers,
but also the memory map is slightly different. The base device
tree vfxxx.dtsi allows to create SoC and board level device trees
supporting the Cortex-M4 while reusing the shared peripherals
nodes.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The clock controller module (CCM) has several clock inputs, which
are connected to external crystal oscillators. To reflect this,
assign these fixed clocks to the CCM node directly.

This especially resolves initialization order dependencies we had
with the earlier initialization code: When resolving of the fixed
clocks failed in clk-vf610, the code created fixed clocks with a
rate of 0.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NJingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The LS1021A TWR is a low cost, high-performance evaluation,
development and test platform supporting the LS1021A processor.
It is optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

For more detail information about the LS1021A TWR board, please
refer to LS1021A QorIQ Tower System Reference Manual.
Signed-off-by: NChao Fu <B44548@freescale.com>
Signed-off-by: NJingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The LS1021A QorIQ development system (QDS) is a high-performance
computing evaluation, development and test platform supporting
the LS1021A processor. The LS1021A QDS is optimized to support
the high-bandwidth DDR3LP/DDR4 memory and a full complement of
high-speed SerDes ports.

For more detail information about the LS1021AQDS, please refer to
the QorIQ LS1021A Development System Reference Manual.
Signed-off-by: NAlison Wang <alison.wang@freescale.com>
Signed-off-by: NChao Fu <B44548@freescale.com>
Signed-off-by: NJason Jin <Jason.Jin@freescale.com>
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: NJaiprakash Singh <b44839@freescale.com>
Signed-off-by: NJingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This add Freescale QorIQ LS1021A SoC device tree support.
The QorIQ LS1021A processor incorporates dual ARM Cortex-A7 cores,
providing virtualization support, advanced security features and the
broadest array of high-speed interconnects and optimized peripheral
features.

The LS1021A SoC shares IPs with i.MX, Vybrid and PowerPC platform.

For the detail information about Freescale QorIQ LS1021A SoC,
please refer to the QorIQ LS1021A Reference Manual.
Signed-off-by: NNikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: NChenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: NSuresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: NShaveta Leekha <shaveta@freescale.com>
Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: NChao Fu <b44548@freescale.com>
Signed-off-by: NTang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: NAlison Wang <alison.wang@freescale.com>
Signed-off-by: NJingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

On registration I2C bus drivers attemp to get ids from device tree
aliases, add a missing alias for I2C4 found on iMX6 DualLite/Solo.
Signed-off-by: NVladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

TBS2910 is a i.MX6Q based board. For additional details refer to
http://www.tbsdtv.com/products/tbs2910-matrix-arm-mini-pc.htmlSigned-off-by: NSoeren Moch <smoch@web.de>
Reviewed-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

TBS Technologies is a company which specializes in developing, producing
and marketing of digital TV tuner cards for PCs.

for additional details refer to http://www.tbsdtv.com/about-us.htmlSigned-off-by: NSoeren Moch <smoch@web.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add enet2 support for imx6sx-sdb board, and add the "fsl,imx6q-fec"
compatible for fec2 node to be compatible with the old version.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add all required properties for the cpufreq-dt driver.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Enable ADC support for Colibri VF61 modules
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The Colibri standard defines four pins as PWM outputs, two of them (PWM
A and C) are routed to FTM instance 0 and the other two (PWM B and D)
are routed to FTM instance 1. Hence enable both FTM instances for the
Colibri module and mux the four pins accordingly.
Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add Global Timer support which is part of the private peripherals
of the Cortex-A5 processor. This Global Timer is compatible with the
Cortex-A9 implementation. It's a 64-bit timer and is clocked by the
peripheral clock, which is typically 133 or 166MHz on Vybrid.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Acked-by: NBill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

SSI block has 'ipg' clock for internal peripheral access and also 'baud' clock
for generating bit clock when SSI operates in master mode.

Add the extra 'baud' clock so that we can have SSI functional in master mode.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

SSI block has 'ipg' clock for internal peripheral access and also 'baud' clock
for generating bit clock when SSI operates in master mode.

Add the extra 'baud' clock so that we can have SSI functional in master mode.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The i.MX SoC update for 3.19:
 - Update i.MX6 suspend code to check DDR instead of CPU type, as the
   difference we need to handle is between LPDDR2 and DDR3, not SoCs.
 - Set anatop properly for LPDDR2 in DSM mode
 - Add support for new SoC LS1021A which integrates dual Cortex-A7
 - Add ENET initialization for i.MX6SX platform
 - Add cpufreq support for i.MX53 platform
 - Add a SNVS based poweroff driver for i.MX6 platforms
 - Use ARM  Global Timer as clocksource on VF610

Note: the change set is built on top of tag imx-fixes-3.18-2 to resolve
a conflict on file arch/arm/mach-imx/clk-vf610.c.

This driver register pm_power_off with snvs power off function. If
your boards NOT use PMIC_ON_REQ to turn on/off external pmic, or use
other pin to do, please disable the driver in dts, otherwise, your
pm_power_off maybe overwrote by this driver.
Signed-off-by: NRobin Gong <b38343@freescale.com>
Acked-By: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The newly introduced LS1021A SoC selects CONFIG_SOC_FSL, which
is originally symbol used for the PowerPC based platforms
and guards lots of code that does not build on ARM.

This breaks allmodconfig, so let's remove it for now, until
either all those drivers are fixed or they use a dependency
on IMX instead.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

With the clock assignment device tree changes, the clocks get
initialized properly but the search for those clocks fails with
errors:

[    0.000000] i.MX clk 4: register failed with -17
[    0.000000] i.MX clk 5: register failed with -17

This is because the module can't find those clocks anymore, and
tries to initialize fixed clocks with the same name.

Get the clock modules input clocks from the assigned clocks by
default by using of_clk_get_by_name(). If this function returns
not a valid clock, fall back to the old behaviour and search the
input clock from the device tree's /clocks/$name node.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Freescale LS1021A SoCs deploy two cortex-A7 processors,
this adds bring-up support for the secondary core.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The LS1021A SoC is a dual-core Cortex-A7 based processor,
this adds the initial support for it.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Instanciate device for the generic cpufreq-dt driver.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The ARM clock is a virtual clock feeding the ARM partition of
the SoC. It controls multiple other clocks to ensure the right
sequencing when cpufreq changes the CPU clock rate.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This implements a virtual clock used to abstract away
all the steps needed in order to change the ARM clock,
so we don't have to push all this clock handling into
the cpufreq driver.

While it will be used for i.MX53 at first it is generic
enough to be used on i.MX6 later on.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This is the bypass clock used to feed the ARM partition
while we reprogram PLL1 to another rate.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add enet init for i.mx6sx:
- Add phy ar8031 fixup
- Set enet clock source from internal PLL
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add imx6sx iomux-gpr register field define in "imx6q-iomuxc-gpr.h" header
file, which is not fully define all iomux-gpr registers and fields, only
align with freescale internal tree related GPR macro define.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add the ARM Global Timer as clocksource/scheduler clock option and
use it as default scheduler clock. This leaves the PIT timer for
other users e.g. the secondary Cortex-M4 core. Also, the Global Timer
has double the precission (running at pheripheral clock compared to
IPG clock) and a 64-bit incrementing counter register. We still keep
the PIT timer as an secondary option in case the ARM Global Timer is
not available.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Acked-by: NBill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

For LPDDR2 platform, no need to enable weak2P5 in DSM mode,
it can be pulled down to save power(~0.65mW).

And per design team's recommendation, we should disconnect
VDDHIGH and SNVS in DSM mode on i.MX6SL.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

As the DDR/IO and MMDC setting are different on LPDDR2 and DDR3,
we used cpu type to decide how to do these settings in suspend
before which is NOT flexible, take i.MX6SL for example, although
it has LPDDR2 on EVK board, but users can also use DDR3 on other
boards, so it is better to read the DDR type from MMDC then decide
how to do related settings.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The i.MX fixes for 3.18, 2nd round:
 - Fix a regression on Vybrid platform which is caused by commit
   dc4805c2 (ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3
   driver), and results in a missing configuration on PLL clocks.
 - Fix a regression with i.MX defconfig files where CONFIG_SPI option
   gets lost accidentally.

Since 64546e9f ("ARM: imx_v6_v7_defconfig updates") and commit
0650f855 ("ARM: imx_v4_v5_defconfig: Select CONFIG_IMX_WEIM") CONFIG_SPI
selection was dropped by savedefconfig for imx_v4_v5_defconfig and
imx_v6_v7_defconfig.

In order to keep the same behaviour as previous kernel versions and avoid
regressions, let's add CONFIG_SPI option back.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

So far, the required PLL's (PLL1/PLL2/PLL5) have been initialized
by boot loader and the kernel code defined fixed rates according
to those default configurations. Beginning with the USB PLL7 the
code started to initialize the PLL's itself (using imx_clk_pllv3).

However, since commit dc4805c2
(ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver)
imx_clk_pllv3 no longer takes care of the ENABLE and BYPASS bits,
hence the USB PLL were not configured correctly anymore.

This patch not only fixes those USB PLL's, but also makes use of
the imx_clk_pllv3 for all PLL's and alignes the code with the PLL
support of the i.MX6 series.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>