Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 165
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 22 3月, 2011 23 次提交
  3. 03 3月, 2011 1 次提交
  5. 21 1月, 2011 1 次提交
    • D
      kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT · 6a108a14
      由 David Rientjes 提交于 
      The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.

This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel.  A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).

Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NDavid Woodhouse <david.woodhouse@intel.com>
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      6a108a14
  7. 19 1月, 2011 4 次提交
    • J
      [media] frontends/ix2505v: Remember to free allocated memory in failure path · 36fd9788
      由 Jesper Juhl 提交于 
      We may leak the storage allocated to 'state' in
drivers/media/dvb/frontends/ix2505v.c::ix2505v_attach() on error, as
it is too early to be able to call ix2505v_release().

This patch makes sure we free the allocated memory in the failure case.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
      36fd9788
    • M
      [media] mb86a20s: Be sure that device is initialized before starting DVB · c736a5f2
      由 Mauro Carvalho Chehab 提交于 
      Due to a hard to track bug between tda829x/tda18271/saa7134, tda829x
wants to go to analog mode during DVB initialization, causing some
I2C errors.

The analog failure doesn't cause any harm, as the device were already
properly initialized in analog mode. However, the failure at the digital
mode causes the frontend mb86a20s to not initialize. Fortunately, at
least on my tests, it was possible to detect that the device is a
mb86a20s before the failure.

What happens is that tda8290 is a very bad boy: during DVB setup, it
keeps insisting to call tda18271 analog_set_params, that calls
tune_agc code. The tune_agc code calls saa7134 driver, changing the
value of GPIO 27, switching from digital to analog mode and disabling
the access to mb86a20s, as, on Kworld SBTVD, the same GPIO used
to switch the hardware AGC mode seems to be used to enable the I2C
switch that allows access to the frontend (mb86a20s).

So, a call to analog_set_params ultimately disables the access to
the frontend, and causes a failure at the init frontend logic.

This patch is a workaround for this issue: it simply checks if the
frontend init had any failure. If so, it will init the frontend when
some DTV application will try to set DVB mode.

Even being a hack for Kworld SBTVD to work, and assumning that we could
teach tda8290 to be a good boy, this is actually an improvement at the
frontend driver, as it will be more reliable to initialization failures.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
      c736a5f2
    • M
      [media] mb86a20s: Fix i2c read/write error messages · 7570800c
      由 Mauro Carvalho Chehab 提交于 
      A script replaced err var to rc. Howerver, this script gambled
"error" string, changing it to "rcor". Revert that bad change.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
      7570800c
    • A
      [media] af9013: fix AF9013 TDA18271 IF config · 82f4b5b6
      由 Antti Palosaari 提交于 
      IF freq	for DVB-T 7 MHz	and 8 MHz was set slightly wrong. Due to that it
didn't worked at all (?) for 7 MHz channels and most likely performance
was dropped for 8 MHz channels.

That bug was pointed by few people during last two months. Thank you.

Trivial fix. Compile tested only due to lack of proper HW and signal.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Cc: Romolo Manfredini <romoloman@hotmail.com>
Cc: Alireza Moini <alireza.moini@silverbrookresearch.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
      82f4b5b6
  9. 29 12月, 2010 11 次提交