We should no longer enter the codec enable/disable functions in question
with port A anyway, but to err on the safe side, keep the warnings. Just
bail out early without messing with the registers.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add support for enabling codec wakeup override signal to allow
re-enumeration of the controller on SKL after resume from low power state.

In SKL, HDMI/DP codec and PCH HD Audio Controller are in different power
wells, so it's necessary to reset display audio codecs when power well on,
otherwise display audio codecs will disappear when resume from low power
state.
Reset steps when power on:
    enable codec wakeup -> azx_init_chip() -> disable codec wakeup

v3 by Jani: Simplify to only support toggling the appropriate chicken bit.

v4 by Han: add explanation and specify the hw swquence.
Signed-off-by: NLu, Han <han.lu@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Unify the HSW/BDW/SKL cdclk extraction code to conform to the same
.get_display_clock_speed() mold that all the other platforms
use.

v2: Update due to SKL code getting added

v3: Rebase on top of -nightly (introduction of intel_audio.c) (Mika Kahola)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: Add v3 note as suggested by Damien.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To match the semantics of drm_crtc->state, which this will eventually
become. The allocation of the memory for config will be fixed in a
followup patch. By adding the extra _config field to intel_crtc it was
possible to generate this entire patch with the cocci script below.

@@ @@
struct intel_crtc {
...
-struct intel_crtc_state config;
+struct intel_crtc_state _config;
+struct intel_crtc_state *config;
...
}
@@ struct intel_crtc *crtc; @@
-memset(&crtc->config, 0, sizeof(crtc->config));
+memset(crtc->config, 0, sizeof(*crtc->config));
@@ @@
__intel_set_mode(...) {
<...
-to_intel_crtc(crtc)->config = *pipe_config;
+(*(to_intel_crtc(crtc)->config)) = *pipe_config;
...>
}
@@ @@
intel_crtc_init(...) {
...
WARN_ON(drm_crtc_index(&intel_crtc->base) != intel_crtc->pipe);
+intel_crtc->config = &intel_crtc->_config;
return;
...
}
@@ struct intel_crtc *crtc; @@
-&crtc->config
+crtc->config
@@ struct intel_crtc *crtc; identifier member; @@
-crtc->config.member
+crtc->config->member
@@ expression E; @@
-&(to_intel_crtc(E)->config)
+to_intel_crtc(E)->config
@@ expression E; identifier member; @@
-to_intel_crtc(E)->config.member
+to_intel_crtc(E)->config->member

v2: Clarify manual changes by splitting them into another patch. (Matt)
    Improve cocci script to generate even more of the changes. (Ander)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And get rid of the duplicate mode structures. This patch was generated
with the following semantic patch:

@@ @@
struct intel_crtc_state {
+struct drm_crtc_state base;
+
...
-struct drm_display_mode requested_mode;
-struct drm_display_mode adjusted_mode;
...
}
@@ struct intel_crtc_state *state; @@
-state->adjusted_mode
+state->base.adjusted_mode
@@ struct intel_crtc_state *state; @@
-state->requested_mode
+state->base.mode
@@ struct intel_crtc_state state; @@
-state.adjusted_mode
+state.base.adjusted_mode
@@ struct intel_crtc_state state; @@
-state.requested_mode
+state.base.mode
@@ struct drm_crtc *crtc; @@
-to_intel_crtc(crtc)->config.adjusted_mode
+to_intel_crtc(crtc)->config.base.adjusted_mode
@@ identifier member; expression E; @@
-PIPE_CONF_CHECK_FLAGS(adjusted_mode.member, E);
+PIPE_CONF_CHECK_FLAGS(base.adjusted_mode.member, E);
@@ identifier member; @@
-PIPE_CONF_CHECK_I(adjusted_mode.member);
+PIPE_CONF_CHECK_I(base.adjusted_mode.member);
@@ identifier member; @@
-PIPE_CONF_CHECK_CLOCK_FUZZY(adjusted_mode.member);
+PIPE_CONF_CHECK_CLOCK_FUZZY(base.adjusted_mode.member);

v2: Completely generate the patch with cocci. (Ander)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Register a component to be used to interface with the snd_hda_intel
driver. This is meant to replace the same interface that is currently
based on module symbol lookup.

v2:
- change roles between the hda and i915 components (Daniel)
- add the implementation to a new file (Jani)
- use better namespacing (Jani)
v3:
- move the implementation to intel_audio.c (Daniel)
- rename display_component to audio_component (Daniel)
- add kerneldoc (Daniel)
v4:
- run forgotten git rm i915_component.c (Jani)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Indicate the monitor has been disconnected on disable.

The regression has been introduced in

commit 5fad84a7
Author: Jani Nikula <jani.nikula@intel.com>
Date:   Tue Nov 4 10:30:23 2014 +0200

    drm/i915: rewrite hsw/bdw audio codec enable/disable sequences

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86424
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The Baseline_ELD_Len field does not include ELD Header Block size.

From High Definition Audio Specification, Revision 1.0a:

	The header block is a fixed size of 4 bytes. The baseline block
	is variable size in multiple of 4 bytes, and its size is defined
	in the header block Baseline_ELD_Len field (in number of
	DWords).

Do not include the header size in Baseline_ELD_Len field. Fix all known
users of eld[2].

While at it, switch to DIV_ROUND_UP instead of open coding it.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NBen Skeggs <bskeggs@redhat.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: NDave Airlie <airlied@linux.ie>
[danvet: Fix compile fail in nouveau.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: include the section in the drm docbook.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This not based on any documentation...
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add support for disabling the audio codec on vlv/chv/gen5-7, similar to
hsw/bdw.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Similar to the hsw/bdw enable sequence rewrite.

v3: replace vblank wait with a comment

v4: expand the comment on what should be done with the vblank wait
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There's some serious confusion regarding ELD valid bit that gets set and
cleared back and forth etc. Rewrite it all based on the documented audio
codec enable/disable sequences.

v3: replace vblank wait with a comment

v4: expand the comment on what should be done with the vblank wait
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make audio related register defines conform to existing style: Add _MASK
where relevant, indent the defines for register contents, don't indent
the defines for register addresses, prefix pipe specific register
address defines with underscores, drop self explanatory comments.

No functional changes.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We'll never end up in the hooks with eld[0] unset, as that's checked by
drm_select_eld().
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Introduce functions to enable/disable the audio codec, incorporating the
ELD setup within enable. The disable is initially limited to HSW,
covering exactly what was done previously.

The only functional difference is that ELD valid is no longer set if
there is no connector with ELD, which should be the right thing to do
anyway. Otherwise the sequence remains the same, with warts and all, in
preparation for applying more sanity.

v2: add kernel doc.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The audio programming sequence states that the ELD must be written and
enabled after the pipe is ready. Indeed, this should clarify the
situation with

commit c7905792
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Wed Apr 16 16:56:09 2014 +0200

    drm/i915: Remove vblank wait from haswell_write_eld

and Ville's review of it [1].

Moreover, we should not touch the relevant registers before we get the
audio power domain.

[1] http://mid.gmane.org/20140416155309.GK18465@intel.comSigned-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Keep the driver modifications to ELD together. This also sets the
Conn_Type for G4X DP which wasn't done before.

Clean up the debugs while at it; this is all obvious from the connector
name.

v3: add missing ~ (Rodrigo)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This will simplify things later on. No functional changes.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Everything else can be derived from that. No functional changes.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Most importantly, "i" need not be the universal variable used for
everything. No functional changes.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Const is good.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In preparation for some additional cleanup. No functional changes.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>