Commit 348f9bb3 ("serial: omap: Fix RTS handling") sought to enable
auto RTS upon manual RTS assertion and disable it on deassertion.
However it seems the latter was done incorrectly, it clears all bits in
the Extended Features Register *except* auto RTS.

Fixes: 348f9bb3 ("serial: omap: Fix RTS handling")
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The do .. while loop checks for interrupt pending at the
start of the loop and exits if there is none, it then
checks again for this condition at the end of the loop.
Signed-off-by: NMartin Townsend <mtownsend1973@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

UART devices is expected to be enumerated by SerDev subsystem.

During ACPI scan, serial devices behind SPI, I2C or UART buses are not
enumerated, allowing them to be enumerated by their respective parents.

Rename *spi_i2c_slave* to *serial_bus_slave* as this will be used for serial
devices on serial buses (SPI, I2C or UART).

On Macs an empty ResourceTemplate is returned for uart slaves.
Instead the device properties "baud", "parity", "dataBits", "stopBits" are
provided. Add a check for "baud" in acpi_is_serial_bus_slave().
Signed-off-by: NFrédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: NRonald Tschalär <ronald@innovation.ch>
Tested-by: NPeter Y. Chuang <peteryuchuang@gmail.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch allows SerDev module to manage serial devices declared as
attached to an UART in ACPI table.

acpi_serdev_add_device() callback will only take into account entries
without enumerated flag set. This flags is set for all entries during
ACPI scan, except for SPI and I2C serial devices, and for UART with
2nd patch in the series.

Check if a serdev device as been allocated during acpi_walk_namespace()
to prevent serdev controller registration instead of the tty-class device.
Signed-off-by: NFrédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: NJohan Hovold <johan@kernel.org>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Define the missing register offsets and bit fields for the extended
UART port. Add a second driver data structure filled with its port data,
selected with the right compatible (marvell,armada-3700-uart-ext).
Signed-off-by: NMiquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A3700 boards may have up to two UART ports. Set the new limit to two
maximum UART ports.
Signed-off-by: NMiquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

While the standard UART port can use a single IRQ that 'sums' both RX
and TX interrupts, the extended port cannot and has to use two different
ISR, one for each direction. The standard port also has the hability
to use two separate interrupts (one for each direction).

The logic is then: either there is only one unnamed interrupt on the
standard port and this interrupt must be used for both directions
(this is legacy bindings); or all the interrupts must be described and
named 'uart-sum' (if available), 'uart-rx', 'uart-tx' and two separate
handlers for each direction will be used.
Suggested-by: NAllen Yan <yanwei@marvell.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Pulse interrupts (extended UART only) needs a change of state to trigger
the TX interrupt. In addition to enabling the TX_READY_INT_EN flag,
produce a FIFO state change from 'empty' to 'not full'. For this, write
only one data byte in TX start, making the TX FIFO not empty, and wait
for the TX interrupt to continue the transfer.
Signed-off-by: NAllen Yan <yanwei@marvell.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When receiving data on RX pin before ->uart_startup() is called, some
error bits in the state register could be set up (like BRK_DET).

This is harmless when using only the standard UART (error bits are
read-only), but may procude an endless loop once in the extended UART
RX interrupt handler (error bits must be cleared).

Clear the status register in ->uart_startup() to avoid this situation.
Signed-off-by: NAllen Yan <yanwei@marvell.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Until now, the first UART port baudrate was set by the bootloader.

Add a function allowing to change the baudrate. Changes may be done
from userspace but also at probe time by the kernel. Use the simplest
method: baudrate divisor.

Works for all UART ports until 230400 baud. To achieve higher baudrates,
software should implement the fractional divisor feature that allows
more accuracy for higher rates.
Signed-off-by: NAllen Yan <yanwei@marvell.com>
[<miquel.raynal@free-electrons.com>: changed termios handling]
Signed-off-by: NMiquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The existing UART driver relies on the bootloader to initialize the
port(s). However, the secondary uart port may not be initialized
properly in early boot stage. This patch adds the UART soft reset when
probing, for all ports.
Signed-off-by: NAllen Yan <yanwei@marvell.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There are two UART ports on Armada3700. The second UART is based on the
first one, plus additional features, but it has a different register
layout (some bit fields are also moved inside the registers).

Clearly separate register offsets and bit fields that differ between the
standard and the extended IP. Access them in a generic way. Rename the
defines with the "STD" prefix for future distinction with "EXT" defines.
Point to these defines in the main driver data structure.

The early console only uses the standard port (not extended).
Suggested-by: NWilson Ding <dingwei@marvell.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Until now, the mvebu-uart driver only supported probing a single UART
port. However, some platforms have multiple instances of this UART
controller, and therefore the driver should support multiple ports.

In order to achieve this, we make sure to assign port->line properly,
instead of hardcoding it to zero.
Signed-off-by: NAllen Yan <yanwei@marvell.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the driver name when requesting an interrupt for consistency.

Avoids possible confusion with DW8250 driver interrupt names in
/proc/interrupts.
Signed-off-by: NYehuda Yitschak <yehuday@marvell.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

pr_err() messages should end with a new-line to avoid other messages
being concatenated.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Amend the Serial device bus Kconfig entries to clarify that you most
likely also want to enable TTY port controller support, and make
SERIAL_DEV_CTRL_TTYPORT default to Y (when bus support is enabled).

Note that the TTY port controller is currently the only in-kernel
serdev controller implementation.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-metag@vger.kernel.org
Signed-off-by: NKees Cook <keescook@chromium.org>
Acked-by: NJames Hogan <jhogan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The SuperIO will be configured at boot time by BIOS, but some BIOS
will not deactivate the SuperIO when the end of configuration. It'll
lead to mismatch for pdata->base_port in probe_setup_port(). So we'll
deactivate all SuperIO before activate special base_port in
fintek_8250_enter_key().

Tested on iBASE MI802.

Cc: stable@vger.kernel.org
Tested-by: NJi-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: NJi-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Reviewd-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

After rmmod 8250.ko
tty_kref_put starts kwork (release_one_tty) to release proc interface
oops when accessing driver->driver_name in proc_tty_unregister_driver

Use jprobe, found driver->driver_name point to 8250.ko
static static struct uart_driver serial8250_reg
.driver_name= serial,

Use name in proc_dir_entry instead of driver->driver_name to fix oops

test on linux 4.1.12:

BUG: unable to handle kernel paging request at ffffffffa01979de
IP: [<ffffffff81310f40>] strchr+0x0/0x30
PGD 1a0d067 PUD 1a0e063 PMD 851c1f067 PTE 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: ... ...  [last unloaded: 8250]
CPU: 7 PID: 116 Comm: kworker/7:1 Tainted: G           O    4.1.12 #1
Hardware name: Insyde RiverForest/Type2 - Board Product Name1, BIOS NE5KV904 12/21/2015
Workqueue: events release_one_tty
task: ffff88085b684960 ti: ffff880852884000 task.ti: ffff880852884000
RIP: 0010:[<ffffffff81310f40>]  [<ffffffff81310f40>] strchr+0x0/0x30
RSP: 0018:ffff880852887c90  EFLAGS: 00010282
RAX: ffffffff81a5eca0 RBX: ffffffffa01979de RCX: 0000000000000004
RDX: ffff880852887d10 RSI: 000000000000002f RDI: ffffffffa01979de
RBP: ffff880852887cd8 R08: 0000000000000000 R09: ffff88085f5d94d0
R10: 0000000000000195 R11: 0000000000000000 R12: ffffffffa01979de
R13: ffff880852887d00 R14: ffffffffa01979de R15: ffff88085f02e840
FS:  0000000000000000(0000) GS:ffff88085f5c0000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffa01979de CR3: 0000000001a0c000 CR4: 00000000001406e0
Stack:
 ffffffff812349b1 ffff880852887cb8 ffff880852887d10 ffff88085f5cd6c2
 ffff880852800a80 ffffffffa01979de ffff880852800a84 0000000000000010
 ffff88085bb28bd8 ffff880852887d38 ffffffff812354f0 ffff880852887d08
Call Trace:
 [<ffffffff812349b1>] ? __xlate_proc_name+0x71/0xd0
 [<ffffffff812354f0>] remove_proc_entry+0x40/0x180
 [<ffffffff815f6811>] ? _raw_spin_lock_irqsave+0x41/0x60
 [<ffffffff813be520>] ? destruct_tty_driver+0x60/0xe0
 [<ffffffff81237c68>] proc_tty_unregister_driver+0x28/0x40
 [<ffffffff813be548>] destruct_tty_driver+0x88/0xe0
 [<ffffffff813be5bd>] tty_driver_kref_put+0x1d/0x20
 [<ffffffff813becca>] release_one_tty+0x5a/0xd0
 [<ffffffff81074159>] process_one_work+0x139/0x420
 [<ffffffff810745a1>] worker_thread+0x121/0x450
 [<ffffffff81074480>] ? process_scheduled_works+0x40/0x40
 [<ffffffff8107a16c>] kthread+0xec/0x110
 [<ffffffff81080000>] ? tg_rt_schedulable+0x210/0x220
 [<ffffffff8107a080>] ? kthread_freezable_should_stop+0x80/0x80
 [<ffffffff815f7292>] ret_from_fork+0x42/0x70
 [<ffffffff8107a080>] ? kthread_freezable_should_stop+0x80/0x80
Signed-off-by: Nnixiaoming <nixiaoming@huawei.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The upper four bits of the XR17V35x fractional divisor register (DLD)
control general chip function (RS-485 direction pin polarity, multidrop
mode, XON/XOFF parity check, and fast IR mode). Don't allow these bits
to be clobbered when setting the baudrate.
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In con_font_set(), when we need to guess font height (for
compat reasons?), the current approach uses multiple userspace
fetches, i.e., get_user(tmp, &charmap[32*i+h-1]), to derive
the height. This has two drawbacks:

1. performance: accessing userspace memory is less efficient than
directly de-reference the byte

2. security: a more critical problem is that the height derived
might not match with the actual font.data. This is because a user
thread might race condition to change the memory of op->data after
the op->height guessing but before the second fetch: font.data =
memdup_user(op->data, size). Leaving font.height = 32 while the
actual height is 1 or vice-versa.

This patch tries to resolve both issues by re-locating the height
guessing part after the font.data is fetched in. In this way, the
userspace data is fetched in one shot and we directly dereference
the font.data in kernel space to probe for the height.
Signed-off-by: NMeng Xu <mengxu.gatech@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The __init attribute is meant to mark functions, use __initdata instead
for the data structure.

This fixes the following error when building with clang:

drivers/tty/serial/sh-sci.c:3247:15: error: '__section__' attribute only
  applies to functions, methods, properties, and global variables
    static struct __init plat_sci_port port_cfg;
Signed-off-by: NMatthias Kaehlcke <mka@chromium.org>
Reviewed-by: NGuenter Roeck <groeck@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the of_device_get_match_data() helper instead of open coding.
Note that when used with DT, there's always a valid match.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The comment in imx_flush_buffer() states that the state of 4 registers
are to be saved/restored, then only saves and restores 3 registers. The
missing register (UBRC) is read only and thus can't be restored.

Update the comment to reflect reality.
Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the tty/serial fixes in here as well.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull SCSI fixes from James Bottomley:

 - a couple of serious fixes: use after free and blacklist for WRITE
   SAME

 - one error leg fix: write_pending failure

 - one user experience problem: do not override max_sectors_kb

 - one minor unused function removal

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ibmvscsis: Fix write_pending failure path
  scsi: libiscsi: Remove iscsi_destroy_session
  scsi: libiscsi: Fix use-after-free race during iscsi_session_teardown
  scsi: sd: Do not override max_sectors_kb sysfs setting
  scsi: sd: Implement blacklist option for WRITE SAME w/ UNMAP

Pull i2c fixes from Wolfram Sang:
 "I2C has three driver fixes for the newly introduced drivers and one ID
  addition for the i801 driver"

* 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i2c-stm32f7: make structure stm32f7_setup static const
  i2c: ensure termination of *_device_id tables
  i2c: i801: Add support for Intel Cedar Fork
  i2c: stm32f7: fix setup structure

Pull MMC fixes from Ulf Hansson:
 "MMC core:

   - Fix driver strength selection when selecting hs400es

   - Delete bounce buffer handling:

     This change fixes a problem related to how bounce buffers are being
     allocated. However, instead of trying to fix that, let's just
     remove the mmc bounce buffer code altogether, as it has practically
     no use.

  MMC host:

   - meson-gx: A couple of fixes related to clock/phase/tuning

   - sdhci-xenon: Fix clock resource by adding an optional bus clock"

* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
  mmc: meson-gx: include tx phase in the tuning process
  mmc: meson-gx: fix rx phase reset
  mmc: meson-gx: make sure the clock is rounded down
  mmc: Delete bounce buffer handling
  mmc: core: add driver strength selection when selecting hs400es

Merge tag 'hwmon-for-linus-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fix from Guenter Roeck:
 "Fix up error path in xgene driver"

* tag 'hwmon-for-linus-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (xgene) Fix up error handling path mixup in 'xgene_hwmon_probe()'

Pull clk fixes from Stephen Boyd:

 - build fix to export the clk_bulk_prepare() symbol

 - suspend fix for Samsung Exynos SoCs where we need to keep clks on
   across suspend

 - two critical clk markings for clks that shouldn't ever turn off on
   Rockchip SoCs

 - a fix for a copy-paste mistake on Rockchip rk3128 causing some clks
   to touch the same bit and trample over one another

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: samsung: exynos4: Enable VPLL and EPLL clocks for suspend/resume cycle
  clk: Export clk_bulk_prepare()
  clk: rockchip: add sclk_timer5 as critical clock on rk3128
  clk: rockchip: fix up rk3128 pvtm and mipi_24m gate regs error
  clk: rockchip: add pclk_pmu as critical clock on rk3128

Pull ARC udpates from Vineet Gupta:

 - updates for various platforms

 - boot log updates for upcoming HS48 family of cores (dual issue)

* tag 'arc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [plat-hsdk]: Add reset controller node to manage ethernet reset
  ARC: [plat-hsdk]: Temporary fix to set CPU frequency to 1GHz
  ARC: fix allnoconfig build warning
  ARCv2: boot log: identify HS48 cores (dual issue)
  ARC: boot log: decontaminate ARCv2 ISA_CONFIG register
  arc: remove redundant UTS_MACHINE define in arch/arc/Makefile
  ARC: [plat-eznps] Update platform maintainer as Noam left
  ARC: [plat-hsdk] use actual clk driver to manage cpu clk
  ARC: [*defconfig] Reenable soft lock-up detector
  ARC: [plat-axs10x] sdio: Temporary fix of sdio ciu frequency
  ARC: [plat-hsdk] sdio: Temporary fix of sdio ciu frequency
  ARC: [plat-axs103] Add temporary quirk to reset ethernet IP

Pull xfs fixes from Darrick Wong:

 - fix a race between overlapping copy on write aio

 - fix cow fork swapping when we defragment reflinked files

* tag 'xfs-4.14-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: handle racy AIO in xfs_reflink_end_cow
  xfs: always swap the cow forks when swapping extents

Pull block fixes from Jens Axboe:
 "A collection of fixes for this series. This contains:

   - NVMe pull request from Christoph, one uuid attribute fix, and one
     fix for the controller memory buffer address for remapped BARs.

   - use-after-free fix for bsg, from Benjamin Block.

   - bcache race/use-after-free fix for a list traversal, fixing a
     regression in this merge window. From Coly Li.

   - null_blk change configfs dependency change from a 'depends' to a
     'select'. This is a change from this merge window as well. From me.

   - nbd signal fix from Josef, fixing a regression introduced with the
     status code changes.

   - nbd MAINTAINERS mailing list entry update.

   - blk-throttle stall fix from Joseph Qi.

   - blk-mq-debugfs fix from Omar, fixing an issue where we don't
     register the IO scheduler debugfs directory, if the driver is
     loaded with it. Only shows up if you switch through the sysfs
     interface"

* 'for-linus' of git://git.kernel.dk/linux-block:
  bsg-lib: fix use-after-free under memory-pressure
  nvme-pci: Use PCI bus address for data/queues in CMB
  blk-mq-debugfs: fix device sched directory for default scheduler
  null_blk: change configfs dependency to select
  blk-throttle: fix possible io stall when upgrade to max
  MAINTAINERS: update list for NBD
  nbd: fix -ERESTARTSYS handling
  nvme: fix visibility of "uuid" ns attribute
  bcache: use llist_for_each_entry_safe() in __closure_wake_up()

Pull PCI fixes from Bjorn Helgaas:
 "Fix legacy IDE probe issues exposed by recent PCI core IRQ mapping
  changes (Bartlomiej Zolnierkiewicz, Lorenzo Pieralisi)"

* tag 'pci-v4.14-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  ide: fix IRQ assignment for PCI bus order probing
  ide: pci: free PCI BARs on initialization failure
  ide: free hwif->portdev on hwif_init() failure

Pull arm64 fixes from Catalin Marinas:

 - Bring initialisation of user space undefined instruction handling
   early (core_initcall) since late_initcall() happens after modprobe in
   initramfs is invoked. Similar fix for fpsimd initialisation

 - Increase the kernel stack when KASAN is enabled

 - Bring the PCI ACS enabling earlier via the
   iort_init_platform_devices()

 - Fix misleading data abort address printing (decimal vs hex)

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Ensure fpsimd support is ready before userspace is active
  arm64: Ensure the instruction emulation is ready for userspace
  arm64: Use larger stacks when KASAN is selected
  ACPI/IORT: Fix PCI ACS enablement
  arm64: fix misleading data abort decoding