DISPC functions are modified in order to work when the manager is LCD2.
This includes:
Adding new IRQs specific to LCD2 and their handling.
Provide dumps of the new manager's registers.
Provide dumps of the new manager's clocks.
Checks for channel for registers DISPC_CONTROL2 and DISPC_CONFIG2
which can't be parametrized.
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NMukund Mittal <mmittal@ti.com>
Signed-off-by: NSamreen <samreen@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The following dispc functions are also changed to incorporate channel as an argument:
	-dispc_lclk_rate()
	-dispc_pclk_rate()
	-dispc_set_pol_freq()
	-dispc_set_clock_div()
	-dispc_get_clock_div()
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NMukund Mittal <mmittal@ti.com>
Signed-off-by: NSamreen <samreen@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
[tomi.valkeinen@nokia.com: fixed trivial compile error]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The interface drivers (dsi.c, sdi.c etc) need to call dispc functions with
dssdev->manager->id as a parameter to specify the DISPC channel which they want
to configure/use, this is required as the same functions are now used to configure
dispc registers of different channels.

The following dispc functions are changed to incorporate channel as an argument:
	-dispc_enable_fifohandcheck()
	-dispc_set_lcd_size()
	-dispc_set_parallel_interface_mode()
	-dispc_set_tft_data_lines()
	-dispc_set_lcd_display_type()
	-dispc_set_lcd_timings()
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NMukund Mittal <mmittal@ti.com>
Signed-off-by: NSamreen <samreen@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
[tomi.valkeinen@nokia.com: fixed trivial compile error]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move check/set/get_timings() from omap_dss_device to omap_dss_driver.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move enable/disable/suspend/resume from omap_dss_device to
omap_dss_driver.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move set/get_update_mode() from omap_dss_device to omap_dss_driver.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move enable/disable_channel() from omap_dss_device to overlay manager.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

dss_select_clk_source() was rather confusing. Selecting the source with
enums is much clearer.

The clk source selection is also stored into memory, so that we know what
is the selected source, even when clocks are off. This is important during
setup, as we need to what clocks to turn on before the clocks are turned
on.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

It looks like on OMAP3 some DSS pins need VDDS_DSI to function properly.

This has not been confirmed from TI, but looking at figure 15-1 "Display
subsystem highlight" from the TRM, some data pins come near the DSI and SDI
blocks. This is not very hard evidence, but the fact remains that with the
power on, pixels are ok, and with the power off, pixels are not ok.

It may also be that VDDS_SDI is needed to power some pins, but as normally
both VDDS_SDI and VDDS_DSI come from the same power source, this hasn't
been shown.

It seems that a single driver can only get a regulator once. This patch
solves it by getting all the required regulators in one place, and from
which the submodules then get the regulators they need.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

This implements MIPI DPI interface.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>