This code is based on code from pcie_extendL1timer() in brcmsmac. This
patch is part of the move of pci specific code from brcmsmac to bcma.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Tested-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This struct contains information about the board, the chip is running
on. The struct is filled for PCIe devices and SoCs. This information is
used by b43 and will be used by brcmsmac soon.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Tested-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Wireless Broadcom chips can have either their SPROM data stored
on either external SPROM or on-chip OTP memory. Both are accessed
through the same register space. This patch adds support for the
on-chip OTP memory.

Tested with:
BCM43224 OTP and SPROM
BCM4331 SPROM
BCM4313 OTP

This patch is in response to linux-wireless thread [1].

[1] http://article.gmane.org/gmane.linux.kernel.wireless.general/85426Tested-by: NSaul St. John <saul.stjohn@gmail.com>
Tested-by: NRafal Milecki <zajec5@gmail.com>
Tested-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On SoCs the sprom is stored in the nvram in a special partition on the
flash chip. The nvram contains the sprom for the main bus, but
sometimes also for a pci devices using bcma. This patch makes it
possible for the arch code to register a function to fetch the needed
sprom from the nvram and provide it to the bcma code.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This function is needed by the bcm47xx arch code to get the number of
the ieee80211 core.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This check is needed on the BCM43224 device as it says in the
capabilities it has an sprom but is extra check says it has not.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we have two bcma buses on one computer the second will not work
without this patch. Now each bus gets an own number.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some SoCs have a PCIe host controller to make it possible to attach
some other devices to it, like an other Wifi card.
This code was tested with an Netgear WNDR3400 (bcm4716 based), but
should work with all bcma based SoCs.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bcma_core_pci_hostmode_init() has to be in __devinit as it will call a
function in that section and so all functions calling it also have to
be in __devinit.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are many magic numbers used in the PCIe code. Replace them with
some constants from the Broadcom SDK and also use them in the pcie host
controller.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some SoCs have two pcie or gmac cores and we need to know the number of
the specific core on the bus. This is the case for the BCM4706.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now the low-level driver actually gets informed that it is getting suspended and resumed.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Just scratching an itch here, but it makes more sense to use the
static keyword if you think about how the compiler treats inline
functions.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The BCMA header only had definitions for 32-bit register access. Used
those as a template for the 16-bit flavour. Also changed them to inline
functions to be on the safe side. As offset parameter is used twice there
would be a problem when used like this: bcma_set32(core, offset++, val);
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The original implementations reference THIS_MODULE in an inline.
We could include <linux/export.h>, but it is better to avoid chaining.

Fortunately someone else already thought of this, and made a similar
inline into a #define in <linux/device.h> for device_schedule_callback(),
[see commit 523ded71] so follow that precedent here.

Also bubble up any __must_check that were used on the prev. wrapper inline
functions up one to the real __register functions, to preserve any prev.
sanity checks that were used in those instances.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to disable ext. PA lines for reading SPROM. It's disabled by
default, but this patch allows using bcma after loading wl, which leaves
workaround enabled.

Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add method to return the clock of the CPU. This is needed by the arch
code to calculate the mips_hpt_frequency.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for serial console to bcma, when operating on an SoC.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds a mips driver to bcma. This is only found on embedded
devices. For now the driver just initializes the irqs used on this
system.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for using bcma on a Broadcom SoC as the system
bus. An SoC like the bcm4716 could register this bus and use it to
searches for the bcma cores and register the devices on this bus.

BCMA_HOSTTYPE_NONE was intended for SoCs at first but BCMA_HOSTTYPE_SOC
is a better name.
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The chip common and mips core have to be setup early in the boot
process to get the cpu clock.
bcma_bus_early_register() gets pointers to some space to store the core
data and searches for the chip common and mips core and initializes
chip common. After that was done and the kernel is out of early boot we
just have to run bcma_bus_register() and it will search for the other
cores, initialize and register them.
The cores are getting the same numbers as before.
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When using DMA, drivers need to pass special translation info to the
hardware.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Recent experiments have shown many cores share 0x1E0 register used for
clock management.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some cards do not use additional 0x30 offset for SPROM location. We do
not know the real condition for it yet, make it BCM4331 specific for
now.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Function managing IRQs is needed for external drivers like b43.
On the other side we do not expect writing any hosts drivers outside of
bcma, so this is safe to do not export functions related to this.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the brcm80211 driver we disable the 80211 core when the driver is
'down'. The bcma_core_disable() function exactly does the same as
our implementation so exporting this function makes sense.

Cc: linux-wireless@vger.kernel.org
Cc: Rafal Milecki <zajec5@gmail.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In case of BCMA cards SPROM is located in the ChipCommon core, it is
not mapped as separated host window. So far we have met only SPROMs rev
8.
SPROM layout seems to be the same as for SSB buses, so we decided to
share SPROM struct and some defines.
For now we extract MAC address only, this can be improved of course.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Similar patch was commited to ssb.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Broadcom has released cards based on a new AMBA-based bus type. From a
programming point of view, this new bus type differs from AMBA and does
not use AMBA common registers. It also differs enough from SSB. We
decided that a new bus driver is needed to keep the code clean.

In its current form, the driver detects devices present on the bus and
registers them in the system. It allows registering BCMA drivers for
specified bus devices and provides them basic operations. The bus driver
itself includes two important bus managing drivers: ChipCommon core
driver and PCI(c) core driver. They are early used to allow correct
initialization.

Currently code is limited to supporting buses on PCI(e) devices, however
the driver is designed to be used also on other hosts. The host
abstraction layer is implemented and already used for PCI(e).

Support for PCI(e) hosts is working and seems to be stable (access to
80211 core was tested successfully on a few devices). We can still
optimize it by using some fixed windows, but this can be done later
without affecting any external code. Windows are just ranges in MMIO
used for accessing cores on the bus.

Cc: Greg KH <greg@kroah.com>
Cc: Michael Büsch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: George Kashperko <george@znau.edu.ua>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Botting <andy@andybotting.com>
Cc: linuxdriverproject <devel@linuxdriverproject.org>
Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>