em28xx driver is capable of handling more than one usb device. However, isoc
transfers require a large amount of data to be transfered.

Before this patch, just one em28xx board were enough to allocate more than 50%
URBs:

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 8
B:  Alloc=480/800 us (60%), #Int=  0, #Iso=  2
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1

So, only one board could use an USB host at the same time. After the patch, it
is possible to use more than one em28xx at the same time, on the same usb host,
if the image size is slower or equal to 345600, since those images will
require about 30% of the URBs:

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 8
B:  Alloc=232/800 us (29%), #Int=  0, #Iso=  2
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1

So, in thesis, after the patch, it would be possible to use up to 3 boards by
each usb host, if the devices are generating small images.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Improves audio configurations on em28xx:
        - mutes audio before changing amux;
        - adds a delay after setting audio src;
        - waits up to 50ms for ac97 busy.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Adds vidioc_[g|s]_register handlers. This allows getting/setting register
from em28xx.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch makes the following needlessly global functions static:
- em28xx-core.c:em28xx_write_reg_bits()
- em28xx-video.c:em28xx_vdev_init()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

has_tuner flag doesn't make much sense, since tuner_type=TUNER_ABSENT
means the same thing.

Having two ways to say that a tuner is not present is
not nice, since it may lead to bad setups. In fact, with the previous
code, if a device were using has_tuner=0, but the user forces a tuner,
with modprobe option tuner=type, the modprobe option won't work.

Also, tveeprom returns TUNER_ABSENT, when tuner is unknown or absent.
So, with the previous logic, in this case, the driver should set
has_tuner=0, or has_tuner=1 otherwise.

Instead of adding several additional tests and setups, better just to
remove .has_tuner.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Before this patch, only Vendor Class audio support were loaded. This means that
older em28xx devices won't have digital audio support loaded.

This patch changes the logic to auto load eighter snd-usb-audio, for devices
with USB Audio Class or em28xx-alsa, for devices with USB Vendor Class.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Older em28xx devices does implement standard Audio Class.

However, on newer devices, this were replaced by a Vendor Class. This
patch autodetects that an em28xx lacks Audio Class and auto-loads
em28xx-alsa, for the devices that implements only a Vendor Class.

For devices with Audio Class, snd-usb-audio module will provide an ALSA
interface.

This patch uses the request_module_async function as defined on cx88-mpeg.c, 
originally wrote by Markus Rechberger.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Also fixes the remaining CodingStyle issues that Lindent didn't fix.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

It is possible to select audio inputs via em28xx or via ac97 functions.
This patch allows configuring a board to use either one way.

It also do some cleanups at audio setup configurations.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

With the conversion to the vidio_ioctl2, tvnorms array is not required anymore.

Also, removed some code from V4L1 time (VIDEO_MODE_foo), specied at the
non-used video_decoder.h.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There were some vestiges of an old V4L1 I2C driver that were called by em28xx.
This patch removes this dead code, and replaces videodev.h to videodev2.h

Now, this driver doesn't require V4L1 anymore.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Uses the newer ioctl handler at videodev. This patch also cleans up some
bad logic at the driver and do CodingStyle and other cleanups at the
resulting driver.

Also, since VIDIOCMBUF were not working, the V4L1 compat code were removed.
The compat code will eventually be re-inserted, if we find a clean way for
implementing compatibility with the old API.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Backport read() fixes from Markus Rechberger.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

On some situations, closing an streaming application and re-opening were
returning -EBUSY.

Uses the same locking schema also present on cx88.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Allows shared access support for em28xx. Just one userspace application is
allowed to get stream. The other(s) application(s) can change V4L2 controls,
set video standards, etc.

This patch were splited from Markus Rechberger's tree and backported to 2.6.17
by Pádraig Brady.

The original patch were ported to the latest em28xx version and had CodingStyle
corrected to solve the issues pointed by scripts/checkpatch.pl.

Thanks to Pádraig Brady <P@draigBrady.com> for pointing this.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Adds autodetection support for the Cinergy200 USB and the VGear PocketTV.

Whenever a usb device with generic empia em2800 usb ids is detected the device
gets scanned for connected i2c devices. If the device list matches an em2800
device in the device list the model id gets changed accordingly.
Signed-off-by: NSascha Sommer <saschasommer@freenet.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The attached patch modifies the em28xx driver so that there can be ioctls from
multiple different threads.

This is necessary for capture apps like MPlayer that use different threads for
capturing and channel tuning.

Now the locking is only done for the ioctls that change properties of the
device or access the i2c bus.

It also removes some locks that look unnecessary:

In em28xx_init_dev:
  the videodevice is not registered yet so nothing can access the hardware
 meanwhile, the device struct is not assigned to the interface yet so no race
 with disconnect is possible

In em28xx_release_resources:
  it gets only called when dev->lock is already held
Signed-off-by: NSascha Sommer <saschasommer@freenet.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch adds a function to allow trying to detect boards that shares
the generic IDs.

The current detection method is based at eeprom checksum.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Currently, the only tuner-specific device that allows special
configurations is tda9887. However, tea5767 also may require some
special configurations (for example, to specify a different Xtal freq).

This patch replaces TDA9887_SET_CONFIG by a more generic internal ioctl
(TUNER_SET_CONFIG). The newer one allows specifying what tuner is
appliable to a configuration set, and allows an arbitrary configuration
struct.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The attached patch is required so that the autodetecion code also works after
a reboot.

Setting the I2C speed does not seem to be supported for em2800.
Signed-off-by: NSascha Sommer <saschasommer@freenet.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This em28xx-video.c uses functions from this header, but doesn't include it.
It depends on some v4l headers included two levels down including poll.h,
which includes mm.h.

These v4l headers might change, so it's best to include the headers needed
directly.

It also causes problems for the out of core build system's backward
compatibility with older kernels, which is the real reason I bothered to
create a patch for something that would otherwise be so minor that it would
hardly be worth the trouble.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

struct video_device used to define a .hardware field. While
initialized on severl drivers, this field is never used inside V4L.
However, drivers using it need to include the old V4L1 header.

This seems to cause compilation troubles with some random configs.
Better just to remove it from all drivers.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>

The rest of V4L files.

There is one list_for_each+list_entry in cpia_pp.c that
wasn't changed because it expects the loop iterator to remain NULL if
the list is empty.

A bug in vivi is fixed; the 'safe' version needs to be used because the loop
deletes the list entries.

Simplify a second loop in vivi and get rid if an un-used variable in that loop.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Some lines later filp->private_data is initialized to dev again.
Since there are some checks that might fail in the mean time
keep the later version.
Signed-off-by: NRolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If, in em28xx_usb_probe() the memory allocation
	dev->alt_max_pkt_size = kmalloc(32*
						dev->num_alt,GFP_KERNEL);
fails, then we'll bail out and return -ENOMEM.
The problem is that in that case we don't free the storage allocated
to 'dev', thus causing a memory leak.

This patch fixes the leak by freeing 'dev' before we return -ENOMEM.
This fixes Coverity bug #647.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMichael Opdenacker <michael@free-electrons.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Many struct file_operations in the kernel can be "const".  Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data.  In addition it'll catch accidental writes at compile time to
these shared resources.

[akpm@sdl.org: dvb fix]
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- CAFE_CCIC needs to depend on PCI, else "allyesconfig" breaks
   on systems without PCI
- em28xx-video can't udelay(2500) else "allyesconfig" breaks
   on systems that refuse to spin that long (I saw it on ARM)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The extra argument makes it possible to reset subsystems of a chip if
that is supported.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

We should no longer try to load the tda9887 module, because it no longer
exists. The tda9887 driver has been merged into the tuner module.
This patch removes all instances of request_module("tda9887") from
the following video4linux drivers: bttv, cx88, em28xx and saa7134.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Use new routing input defines in em28xx-cards.c
- Fix S-Video settings for tvp5150-based cards (input was copied from saa7115
  based cards and worked only because S-Video was selected in the default: case)
- Replace VIDIOC_S_INPUT by VIDIOC_INT_S_VIDEO_ROUTING in em28xx-video.c
- Remove the now obsolete VIDIOC_S_INPUT handler in saa7115.c
- Add VIDIOC_INT_G/S_VIDEO_ROUTING in tvp5150.c
- Add new media/tvp5150.h with the routing defines.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

In several places we use dev->devno right after we kfree() dev.  This fixes
coverity bug id #1065
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>