This fixes "Too few good blocks within range" issues on GoFlex Net by setting
chip-delay to 40.

The basic problem was discussed at http://forum.doozan.com/read.php?2,7451Signed-off-by: NEric Hutter <hutter.eric@gmail.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.6.x
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The orion5x-lacie-ethernet-disk-mini-v2.dts file was using
"marvell-orion5x-88f5182" as a compatible string, while it should have
been "marvell,orion5x-88f5182".
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

There is no need to have a #address-cells property in the MPIC Device
Tree node, and more than that, having it confuses the of_irq_map_raw()
logic, which will be used by the Marvell PCIe driver.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

During the system initialization, the orion_setup_cpu_mbus_target()
function reads the SDRAM address decoding registers to find out how
many chip-selects of SDRAM have been enabled, and builds a small array
with one entry per chip-select. This array is then used by device
drivers (XOR, Ethernet, etc.) to configure their own address decoding
windows to the SDRAM.

However, devices can only access the first 32 bits of the physical
memory. Even though LPAE is not supported for now, some Marvell boards
are now showing up with 8 GB of RAM, configured using two SDRAM
address decoding windows: the first covering the first 4 GB, the
second covering the last 4 GB. The array built by
orion_setup_cpu_mbus_target() has therefore two entries, and device
drivers try to set up two address decoding windows to the
SDRAM. However, in the device registers for the address decoding, the
base address is only 32 bits, so those two windows overlap each other,
and the devices do not work at all.

This patch makes sure that the array built by
orion_setup_cpu_mbus_target() only contains the SDRAM decoding windows
that correspond to the first 4 GB of the memory. To do that, it
ignores the SDRAM decoding windows for which the 4 low-order bits are
not zero (the 4 low-order bits of the base register are used to store
bits 32:35 of the base address, so they actually indicate whether the
base address is above 4 GB).

This patch allows the newly introduced armada-xp-gp board to properly
operate when it is mounted with more than 4 GB of RAM. Without that,
all devices doing DMA (for example XOR and Ethernet) do not work at
all.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Setting the reg-io-width to 1 byte represents more accurate
description of the HW.

This will fix an issue where UART driver causes kernel
panic during bootup. Gregory CLEMENT traced the issue to
autoconfig() in 8250.c, where the existence of FIFO is
checked from UART_IIR register. The register is now read as
32-bit value as the reg-io-width is set to 4-bytes. The
retuned value seems to contain bogus data for bits 31:8,
causing the issue.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The commit:

  48be9ac9 ARM: Dove: split legacy and DT setup

removed the RTC initialization.  This patch re-enables the RTC
via the DT.
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch modifies the Armada 370 Reference Design DTS file to enable
support for the two USB ports found on this board.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Commit 5b03df9a ("ARM: dove: switch to
DT clock providers") added "select COMMON_CLK_DOVE" to Marvell Dove's
Kconfig entry. But there's no Kconfig symbol COMMON_CLK_DOVE, which
makes this select statement a nop. It's probably a leftover of some
experimental code that never hit mainline. Drop it.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The kirkwood SoC GPIO cores use the runit clock. Add code to
clk_prepare_enable() runit, otherwise there is a danger of locking up
the SoC by accessing the GPIO registers when runit clock is not
ticking.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The ethernet controller used on kirkwood looses its MAC address
register contents when the corresponding clock is gated. As soon as
mv643xx_eth is built as module, the clock gets gated and when loading
the module, the MAC address is gone.

Proper DT support for the mv643xx_eth driver is expected soon, so we add
a workaround to always enable ge0/ge1 clocks on kirkwood. This workaround
is also already used on non-DT kirkwood kernels.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

When DT support for kirkwood was first introduced, there was no clock
infrastructure.  As a result, we had to manually pass the
clock-frequency to the driver from the device node.

Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.

The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.

Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.

Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Pull fbdev UAPI disintegration from David Howells:
 "You'll be glad to here that the end is nigh for the UAPI patches.
  Only the fbdev/framebuffer piece remains now that the SCSI stuff has
  gone in.

  Here are the UAPI disintegration bits for the fbdev drivers.  It
  appears that Florian hasn't had time to deal with my patch, but back
  in December he did say he didn't mind if I pushed it forward."

Yay.  No more uapi movement.  And hopefully no more big header file
cleanups coming up either, it just tends to be very painful.

* tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers:
  UAPI: (Scripted) Disintegrate include/video

Merge tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
 - Update the Xen ACPI memory and CPU hotplug locking mechanism.
 - Fix PAT issues wherein various applications would not start
 - Fix handling of multiple MSI as AHCI now does it.
 - Fix ARM compile failures.

* tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xenbus: fix compile failure on ARM with Xen enabled
  xen/pci: We don't do multiple MSI's.
  xen/pat: Disable PAT using pat_enabled value.
  xen/acpi: xen cpu hotplug minor updates
  xen/acpi: xen memory hotplug minor updates

Pull  more VFS bits from Al Viro:
 "Unfortunately, it looks like xattr series will have to wait until the
  next cycle ;-/

  This pile contains 9p cleanups and fixes (races in v9fs_fid_add()
  etc), fixup for nommu breakage in shmem.c, several cleanups and a bit
  more file_inode() work"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  constify path_get/path_put and fs_struct.c stuff
  fix nommu breakage in shmem.c
  cache the value of file_inode() in struct file
  9p: if v9fs_fid_lookup() gets to asking server, it'd better have hashed dentry
  9p: make sure ->lookup() adds fid to the right dentry
  9p: untangle ->lookup() a bit
  9p: double iput() in ->lookup() if d_materialise_unique() fails
  9p: v9fs_fid_add() can't fail now
  v9fs: get rid of v9fs_dentry
  9p: turn fid->dlist into hlist
  9p: don't bother with private lock in ->d_fsdata; dentry->d_lock will do just fine
  more file_inode() open-coded instances
  selinux: opened file can't have NULL or negative ->f_path.dentry

(In the meantime, the hlist traversal macros have changed, so this
required a semantic conflict fixup for the newly hlistified fid->dlist)

Pull btrfs fixup from Chris Mason:
 "Geert and James both sent this one in, sorry guys"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs/raid56: Add missing #include <linux/vmalloc.h>

Pull second set of s390 patches from Martin Schwidefsky:
 "The main part of this merge are Heikos uaccess patches.  Together with
  commit 09884964 ("mm: do not grow the stack vma just because of an
  overrun on preceding vma") the user string access is hopefully fixed
  for good.

  In addition some bug fixes and two cleanup patches."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/module: fix compile warning
  qdio: remove unused parameters
  s390/uaccess: fix kernel ds access for page table walk
  s390/uaccess: fix strncpy_from_user string length check
  input: disable i8042 PC Keyboard controller for s390
  s390/dis: Fix invalid array size
  s390/uaccess: remove pointless access_ok() checks
  s390/uaccess: fix strncpy_from_user/strnlen_user zero maxlen case
  s390/uaccess: shorten strncpy_from_user/strnlen_user
  s390/dasd: fix unresponsive device after all channel paths were lost
  s390/mm: ignore change bit for vmemmap
  s390/page table dumper: add support for change-recording override bit

Merge branch 'fixes-for-3.9-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux

Pull second round of PARISC updates from Helge Deller:
 "The most important fix in this branch is the switch of io_setup,
  io_getevents and io_submit syscalls to use the available compat
  syscalls when running 32bit userspace on 64bit kernel.  Other than
  that it's mostly removal of compile warnings."

* 'fixes-for-3.9-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: fix redefinition of SET_PERSONALITY
  parisc: do not install modules when installing kernel
  parisc: fix compile warnings triggered by atomic_sub(sizeof(),v)
  parisc: check return value of down_interruptible() in hp_sdc_rtc.c
  parisc: avoid unitialized variable warning in pa_memcpy()
  parisc: remove unused variable 'compat_val'
  parisc: switch to compat_functions of io_setup, io_getevents and io_submit
  parisc: select ARCH_WANT_FRAME_POINTERS

Pull new ImgTec Meta architecture from James Hogan:
 "This adds core architecture support for Imagination's Meta processor
  cores, followed by some later miscellaneous arch/metag cleanups and
  fixes which I kept separate to ease review:

   - Support for basic Meta 1 (ATP) and Meta 2 (HTP) core architecture
   - A few fixes all over, particularly for symbol prefixes
   - A few privilege protection fixes
   - Several cleanups (setup.c includes, split out a lot of
     metag_ksyms.c)
   - Fix some missing exports
   - Convert hugetlb to use vm_unmapped_area()
   - Copy device tree to non-init memory
   - Provide dma_get_sgtable()"

* tag 'metag-v3.9-rc1-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag: (61 commits)
  metag: Provide dma_get_sgtable()
  metag: prom.h: remove declaration of metag_dt_memblock_reserve()
  metag: copy devicetree to non-init memory
  metag: cleanup metag_ksyms.c includes
  metag: move mm/init.c exports out of metag_ksyms.c
  metag: move usercopy.c exports out of metag_ksyms.c
  metag: move setup.c exports out of metag_ksyms.c
  metag: move kick.c exports out of metag_ksyms.c
  metag: move traps.c exports out of metag_ksyms.c
  metag: move irq enable out of irqflags.h on SMP
  genksyms: fix metag symbol prefix on crc symbols
  metag: hugetlb: convert to vm_unmapped_area()
  metag: export clear_page and copy_page
  metag: export metag_code_cache_flush_all
  metag: protect more non-MMU memory regions
  metag: make TXPRIVEXT bits explicit
  metag: kernel/setup.c: sort includes
  perf: Enable building perf tools for Meta
  metag: add boot time LNKGET/LNKSET check
  metag: add __init to metag_cache_probe()
  ...

Pull late ARM updates from Russell King:
 "Here is the late set of ARM updates for this merge window; in here is:

   - The ARM parts of the broadcast timer support, core parts merged
     through tglx's tree.  This was left over from the previous merge to
     allow the dependency on tglx's tree to be resolved.

   - A fix to the VFP code which shows up on Raspberry Pi's, as well as
     fixing the fallout from a previous commit in this area.

   - A number of smaller fixes scattered throughout the ARM tree"

* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: Fix broken commit 0cc41e4a corrupting kernel messages
  ARM: fix scheduling while atomic warning in alignment handling code
  ARM: VFP: fix emulation of second VFP instruction
  ARM: 7656/1: uImage: Error out on build of multiplatform without LOADADDR
  ARM: 7640/1: memory: tegra_ahb_enable_smmu() depends on TEGRA_IOMMU_SMMU
  ARM: 7654/1: Preserve L_PTE_VALID in pte_modify()
  ARM: 7653/2: do not scale loops_per_jiffy when using a constant delay clock
  ARM: 7651/1: remove unused smp_timer_broadcast #define

Pull char/misc patch from Greg Kroah-Hartman:
 "Here is one remaining patch for 3.9-rc1.  It is for the hyper-v
  drivers, and had to wait until some other patches went in through the
  x86 tree."
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Drivers: hv: vmbus: Use the new infrastructure for delivering VMBUS interrupts

Pull USB patch revert from Greg Kroah-Hartman:
 "Here is one remaining USB patch for 3.9-rc1, it reverts a 3.8 patch
  that has caused a lot of regressions for some VIA EHCI controllers."

* tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: EHCI: revert "remove ASS/PSS polling timeout"

Pull watchdog updates from Wim Van Sebroeck:
 "This contains:
   - fixes and improvements
   - devicetree bindings
   - conversion to watchdog generic framework of the following drivers:
        - booke_wdt
        - bcm47xx_wdt.c
        - at91sam9_wdt
   - Removal of old STMP3xxx driver
   - Addition of following new drivers:
        - new driver for STMP3xxx and i.MX23/28
        - Retu watchdog driver"

* git://www.linux-watchdog.org/linux-watchdog: (30 commits)
  watchdog: sp805_wdt depends on ARM
  watchdog: davinci_wdt: update to devm_* API
  watchdog: davinci_wdt: use devm managed clk get
  watchdog: at91rm9200: add DT support
  watchdog: add timeout-sec property binding
  watchdog: at91sam9_wdt: Convert to use the watchdog framework
  watchdog: omap_wdt: Add option nowayout
  watchdog: core: dt: add support for the timeout-sec dt property
  watchdog: bcm47xx_wdt.c: add hard timer
  watchdog: bcm47xx_wdt.c: rename wdt_time to timeout
  watchdog: bcm47xx_wdt.c: rename ops methods
  watchdog: bcm47xx_wdt.c: use platform device
  watchdog: bcm47xx_wdt.c: convert to watchdog core api
  watchdog: Convert BookE watchdog driver to watchdog infrastructure
  watchdog: s3c2410_wdt: Use devm_* functions
  watchdog: remove old STMP3xxx driver
  watchdog: add new driver for STMP3xxx and i.MX23/28
  rtc: stmp3xxx: add wdt-accessor function
  watchdog: introduce retu_wdt driver
  watchdog: intel_scu_watchdog: fix Kconfig dependency
  ...

Pull second set of slave-dmaengine updates from Vinod Koul:
 "Arnd's patch moves the dw_dmac to use generic DMA binding.  I agreed
  to merge this late as it will avoid the conflicts between trees.

  The second patch from Matt adding a dma_request_slave_channel_compat
  API was supposed to be picked up, but somehow never got picked up.
  Some patches dependent on this are already in -next :("

* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: dw_dmac: move to generic DMA binding
  dmaengine: add dma_request_slave_channel_compat()

Pull x86 platform driver updates from Matthew Garrett:
 "Mostly relatively small updates, along with some hardware enablement
  for Sony hardware and a pile of updates to Google's Chromebook driver"

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (49 commits)
  ideapad-laptop: Depend on BACKLIGHT_CLASS_DEVICE instead of selecting it
  ideapad: depends on backlight subsystem and update comment
  Platform: x86: chromeos_laptop - add i915 gmbuses to adapter names
  Platform: x86: chromeos_laptop - Add isl light sensor for Pixel
  Platform: x86: chromeos_laptop - Add a more general add_i2c_device
  Platform: x86: chromeos_laptop - Add Pixel Touchscreen
  Platform: x86: chromeos_laptop - Add support for probing devices
  Platform: x86: chromeos_laptop - Add Pixel Trackpad
  hp-wmi: fix handling of platform device
  sony-laptop: leak in error handling sony_nc_lid_resume_setup()
  hp-wmi: Add support for SMBus hotkeys
  asus-wmi: Fix unused function build warning
  acer-wmi: avoid the warning of 'devices' may be used uninitialized
  drivers/platform/x86/thinkpad_acpi.c: Handle HKEY event 0x6040
  Platform: x86: chromeos_laptop - Add HP Pavilion 14
  Platform: x86: chromeos_laptop - Add Taos tsl2583 device
  Platform: x86: chromeos_laptop - Add Taos tsl2563 device
  Platform: x86: chromeos_laptop - Add Acer C7 trackpad
  Platform: x86: chromeos_laptop - Rename setup_lumpy_tp to setup_cyapa_smbus_tp
  asus-laptop: always report brightness key events
  ...

tilegx_defconfig:

fs/btrfs/raid56.c: In function 'btrfs_alloc_stripe_hash_table':
fs/btrfs/raid56.c:206:3: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration]
fs/btrfs/raid56.c:206:9: warning: assignment makes pointer from integer without a cast [enabled by default]
fs/btrfs/raid56.c:226:4: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

Pull ext4 bug fixes from Ted Ts'o:
 "Various bug fixes for ext4.  The most important is a fix for the new
  extent cache's slab shrinker which can cause significant, user-visible
  pauses when the system is under memory pressure."

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: enable quotas before orphan cleanup
  ext4: don't allow quota mount options when quota feature enabled
  ext4: fix a warning from sparse check for ext4_dir_llseek
  ext4: convert number of blocks to clusters properly
  ext4: fix possible memory leak in ext4_remount()
  jbd2: fix ERR_PTR dereference in jbd2__journal_start
  ext4: use percpu counter for extent cache count
  ext4: optimize ext4_es_shrink()

Pull sigprocmask compat fix from Al Viro:
 "generic compat_sys_rt_sigprocmask() had a very dumb braino; I'd spent
  quite a while staring at the offending commit before finally managing
  to spot the idiocy ;-/"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
  fix compat_sys_rt_sigprocmask()

Converting bitmask to 32bit granularity is fine, but we'd better
_do_ something with the result.  Such as "copy it to userland"...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Pull NFS client bugfixes from Trond Myklebust:
 "We've just concluded another Connectathon interoperability testing
  week, and so here are the fixes for the bugs that were discovered:

   - Don't allow NFS silly-renamed files to be deleted
   - Don't start the retransmission timer when out of socket space
   - Fix a couple of pnfs-related Oopses.
   - Fix one more NFSv4 state recovery deadlock
   - Don't loop forever when LAYOUTGET returns NFS4ERR_LAYOUTTRYLATER"

* tag 'nfs-for-3.9-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  SUNRPC: One line comment fix
  NFSv4.1: LAYOUTGET EDELAY loops timeout to the MDS
  SUNRPC: add call to get configured timeout
  PNFS: set the default DS timeout to 60 seconds
  NFSv4: Fix another open/open_recovery deadlock
  nfs: don't allow nfs_find_actor to match inodes of the wrong type
  NFSv4.1: Hold reference to layout hdr in layoutget
  pnfs: fix resend_to_mds for directio
  SUNRPC: Don't start the retransmission timer when out of socket space
  NFS: Don't allow NFS silly-renamed files to be deleted, no signal

Pull btrfs update from Chris Mason:
 "The biggest feature in the pull is the new (and still experimental)
  raid56 code that David Woodhouse started long ago.  I'm still working
  on the parity logging setup that will avoid inconsistent parity after
  a crash, so this is only for testing right now.  But, I'd really like
  to get it out to a broader audience to hammer out any performance
  issues or other problems.

  scrub does not yet correct errors on raid5/6 either.

  Josef has another pass at fsync performance.  The big change here is
  to combine waiting for metadata with waiting for data, which is a big
  latency win.  It is also step one toward using atomics from the
  hardware during a commit.

  Mark Fasheh has a new way to use btrfs send/receive to send only the
  metadata changes.  SUSE is using this to make snapper more efficient
  at finding changes between snapshosts.

  Snapshot-aware defrag is also included.

  Otherwise we have a large number of fixes and cleanups.  Eric Sandeen
  wins the award for removing the most lines, and I'm hoping we steal
  this idea from XFS over and over again."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (118 commits)
  btrfs: fixup/remove module.h usage as required
  Btrfs: delete inline extents when we find them during logging
  btrfs: try harder to allocate raid56 stripe cache
  Btrfs: cleanup to make the function btrfs_delalloc_reserve_metadata more logic
  Btrfs: don't call btrfs_qgroup_free if just btrfs_qgroup_reserve fails
  Btrfs: remove reduplicate check about root in the function btrfs_clean_quota_tree
  Btrfs: return ENOMEM rather than use BUG_ON when btrfs_alloc_path fails
  Btrfs: fix missing deleted items in btrfs_clean_quota_tree
  btrfs: use only inline_pages from extent buffer
  Btrfs: fix wrong reserved space when deleting a snapshot/subvolume
  Btrfs: fix wrong reserved space in qgroup during snap/subv creation
  Btrfs: remove unnecessary dget_parent/dput when creating the pending snapshot
  btrfs: remove a printk from scan_one_device
  Btrfs: fix NULL pointer after aborting a transaction
  Btrfs: fix memory leak of log roots
  Btrfs: copy everything if we've created an inline extent
  btrfs: cleanup for open-coded alignment
  Btrfs: do not change inode flags in rename
  Btrfs: use reserved space for creating a snapshot
  clear chunk_alloc flag on retryable failure
  ...

Pull MTD update from David Woodhouse:
 "Fairly unexciting MTD merge for 3.9:

   - misc clean-ups in the MTD command-line partitioning parser
     (cmdlinepart)
   - add flash locking support for STmicro chips serial flash chips, as
     well as for CFI command set 2 chips.
   - new driver for the ELM error correction HW module found in various
     TI chips, enable the OMAP NAND driver to use the ELM HW error
     correction
   - added number of new serial flash IDs
   - various fixes and improvements in the gpmi NAND driver
   - bcm47xx NAND driver improvements
   - make the mtdpart module actually removable"

* tag 'for-linus-20130301' of git://git.infradead.org/linux-mtd: (45 commits)
  mtd: map: BUG() in non handled cases
  mtd: bcm47xxnflash: use pr_fmt for module prefix in messages
  mtd: davinci_nand: Use managed resources
  mtd: mtd_torturetest can cause stack overflows
  mtd: physmap_of: Convert device allocation to managed devm_kzalloc()
  mtd: at91: atmel_nand: for PMECC, add code to check the ONFI parameter ECC requirement.
  mtd: atmel_nand: make pmecc-cap, pmecc-sector-size in dts is optional.
  mtd: atmel_nand: avoid to report an error when lookup table offset is 0.
  mtd: bcm47xxsflash: adjust names of bus-specific functions
  mtd: bcm47xxpart: improve probing of nvram partition
  mtd: bcm47xxpart: add support for other erase sizes
  mtd: bcm47xxnflash: register this as normal driver
  mtd: bcm47xxnflash: fix message
  mtd: bcm47xxsflash: register this as normal driver
  mtd: bcm47xxsflash: write number of written bytes
  mtd: gpmi: add sanity check for the ECC
  mtd: gpmi: set the Golois Field bit for mx6q's BCH
  mtd: devices: elm: Removes <xx> literals in elm DT node
  mtd: gpmi: fix a dereferencing freed memory error
  mtd: fix the wrong timeo for panic_nand_wait()
  ...

Reported-by: NWeston Andros Adamson <dros@netapp.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

When using quota feature we need to enable quotas before orphan cleanup
so that changes happening during it are properly reflected in quota
accounting.
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>

So far we silently ignored when quota mount options were set while quota
feature was enabled.  But this can create confusion in userspace when
mount options are set but silently ignored and also creates opportunities
for bugs when we don't properly test all quota types.  Actually
ext4_mark_dquot_dirty() forgets to test for quota feature so it was
dependent on journaled quota options being set.  OTOH ext4_orphan_cleanup()
tries to enable journaled quota when quota options are specified which is
wrong when quota feature is enabled.
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>

ext4_dir_llseek is only used as a callback function, and no one calls
it directly.  So make it as a static function in order to remove a
warning message from sparse check.
Signed-off-by: NZheng Liu <wenqing.lz@taobao.com>
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>

We're using macro EXT4_B2C() to convert number of blocks to number of
clusters for bigalloc file systems.  However, we should be using
EXT4_NUM_B2C().
Signed-off-by: NLukas Czerner <lczerner@redhat.com>
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org

'orig_data' is malloced in ext4_remount() and should be freed
before leaving from the error handling cases, otherwise it will
cause memory leak.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: NLukas Czerner <lczerner@redhat.com>
Cc: stable@vger.kernel.org