'Reset' loop does not look correct. I tested it very many times and
it never repeated those commands. If problem, it tries to solve,
really occurs on some situations better solution should be find out.

There is another patch which does not have such hackish looking loop.
Lets change to it.

Cc: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The XV601/709 encodings are special: they signal limited range, but use the full range
to encode a larger gamut with R', G' and B' values outside the [0-1] range.

So don't clamp to limited range for these two encodings.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The XV601/709 Y'CbCr encoding was changed to limited range, but the comment
still indicates full range.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Some of the macros didn't use the parenthesis around the parameters when
used in the body of the macro.
Signed-off-by: NNikola Jelic <nikola.jelic83@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

If DMA does not support INTERLEAVE, deinterlace_probe() breaks off
initialization, releases dma channel, but returns zero.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

TRY_FMT already disables the YUYV format if the VDOA is not available.
ENUM_FMT must do the same.

Fixes: d40e98c1 ("[media] coda: support YUYV output if VDOA is used")
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Even if field order is set to V4L2_FIELD_ALTERNATE, the width and height
values in struct v4l2_mbus_framefmt still refer to frame size, not field
size.

Fixes: 4f57d27b ("[media] tvp5150: fix tvp5150_fill_fmt()")
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

To let userspace propagate formats downstream in a media controller
scenario, the video source pad (now pad 1, DEMOD_PAD_VID_OUT) must allow
setting and getting the format. Incidentally, tvp5150_fill_fmt was
implemented for this pad, not for the new analog input pad (now pad 0,
DEMOD_PAD_IF_INPUT).

Fixes: 55606310 ("[media] tvp5150: create the expected number of pads")
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The call to v4ls_m2m_get_vq is only used to get the return value
which is not being used, so it appears to be redundant and can
be removed.

Detected with CoverityScan, CID#1420674 ("Useless call")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The em28xx driver still used the soc_camera.h header for the ov2640
driver. Since this driver no longer uses soc_camera, that include can
be removed.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The MC support is needed by the em28xx driver.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Convert v4l2_clk to normal clk and enable the clock.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Convert ov2640 to a standard subdev driver. The soc-camera driver no longer
uses this driver, so it can safely be converted.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

It is a bit confusing how CEC_CAP_RC and IS_REACHABLE(CONFIG_RC_CORE)
interact. By stripping CEC_CAP_RC at the beginning rather than after #else
it should be a bit clearer what is going on.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Reported-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Currently when the RC Core is enabled (reachable) core code located
in cec_register_adapter() attempts to populate the RC structure with
a pointer to the 'parent' passed in by the caller.

Unfortunately if the caller did not specify RC capability when calling
cec_allocate_adapter(), then there will be no RC structure to populate.

This causes a "NULL pointer dereference" error.

Fixes: f51e8080 ("[media] cec: pass parent device in register(), not allocate()")
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Cc: <stable@vger.kernel.org>      # for v4.10 and up
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.

Update the bindings documenting the new hdmi phandle and
update exynos4.dtsi accordingly.

Tested with my Odroid U3.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NKrzysztof Kozlowski <krzk@kernel.org>
CC: linux-samsung-soc@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Update the bindings documenting the new hdmi phandle.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NKrzysztof Kozlowski <krzk@kernel.org>
Acked-by: NRob Herring <robh@kernel.org>
CC: linux-samsung-soc@vger.kernel.org
CC: devicetree@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add the new hdmi phandle to exynos4.dtsi. This phandle is needed by the
s5p-cec driver to initialize the CEC notifier framework.

Tested with my Odroid U3.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
CC: linux-samsung-soc@vger.kernel.org
CC: devicetree@vger.kernel.org
CC: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Implement the CEC notifier support to allow CEC drivers to
be informed when there is a new physical address.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NKrzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

To use CEC notifier sti CEC driver needs to get phandle
of the hdmi device.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
CC: Patrice CHOTARD <patrice.chotard@st.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Update the bindings documentation with the new hdmi phandle.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Implement the CEC notifier support to allow CEC drivers to
be informed when there is a new physical address.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Support the CEC notifier framework, simplifying drivers that
depend on this.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Tested-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add support for CEC notifiers, which is used to convey CEC physical address
information from video drivers to their CEC counterpart driver(s).

Based on an earlier version from Russell King:

https://patchwork.kernel.org/patch/9277043/

The cec_notifier is a reference counted object containing the CEC physical address
state of a video device.

When a new notifier is registered the current state will be reported to
that notifier at registration time.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Tested-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Implement DVBv5 PER.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Implement DVBv5 CNR.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Implement DVBv5 signal strength on relative scale.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This driver supports the RainShadow Tech USB HDMI CEC adapter.

See: http://rainshadowtech.com/HdmiCecUsb.htmlSigned-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>