- 30 8月, 2017 21 次提交
-
-
由 Shawn Lin 提交于
It was never used and introduced a long standing compile warning: drivers/mmc/core/block.c: In function 'power_ro_lock_store': drivers/mmc/core/block.c:191:19: warning: variable 'card' set but not used [-Wunused-but-set-variable] Remove it to fix the warning. Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Shawn Lin 提交于
We got a compile warning for mxcmmc, drivers/mmc/host/mxcmmc.c: In function 'mxcmci_data_done': drivers/mmc/host/mxcmmc.c:661:6: warning: variable 'data_error' set but not used [-Wunused-but-set-variable] The easiest method is to remove the data_error. But looking into the code closely, I think we should check the return value of mxcmci_finish_data as if it got data->error(the same as data_error), we shouldn't try to read the response. Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Shawn Lin 提交于
Just a trivial fix for that found by reading the code. Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com> Reviewed-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Chaotian Jing 提交于
if user plug out sd card slowly, finally card is plugged out but cat /proc/partitions can find that card is still exist in kernel. that's because alougth get card detect interrupt but CMD13 still can get correct response(all other pins are connected expect card detect pin). add ops->get_cd() can avoid this issue. Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Colin Ian King 提交于
array width is on-stack and not modified and should be made static const. Signed-off-by: NColin Ian King <colin.king@canonical.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Wolfram Sang 提交于
Most registers need to wait until the command is completed, not necessarily until the bus is free. At least, R-Car 2+ SoCs can signal that via the CBSY bit, so let's use it there instead of SCLKDIVEN to save a little bit of delay. Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Wolfram Sang 提交于
Our hardware engineers confirmed that it is unnecessary to wait when turning the clock on/off. The documentation was a tad vague, so we used to play safe. Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Wolfram Sang 提交于
Use a proper define. Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Wolfram Sang 提交于
When defining bits, make sure we always have a reference to the register they belong to. For now, renaming all bits properly seems too intrusive, so at least make sure we have proper documentation. Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Wolfram Sang 提交于
Since commit 10c7fcbd ("ARM: shmobile: sh7372: Remove ZBOOT MMC/SDHI support"), this define is not needed anymore. Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Wolfram Sang 提交于
I always anticipated this code to be not correct, but now I had a test case to prove it. According to all documentation I have, setting the TMIO_STOP_STP bit ever only worked during block transfers. This bit is like manually enforcing an autocmd12 during a so far seamless transfer. It does NOT work when the block transfer had errors. It also does NOT work with any other cmd except block commands. For all those, CMD12 has to be treated like any other command. So, basically, we could use this bit only for mrq->data->stop cmds. But for these, we happily use the autocmd12 feature using the TMIO_STOP_SEC bit. As a result, the above bit is not useful for us and we need to treat CMD12 as a regular cmd always. Just remove the special handling code. Note that the BSP recognized this issue as well yet had a more cautious solution to the problem [1]. Which is understandable but makes CMD12 handling even more complicated. Checked with a Renesas Salvator-X/M3-W which needed to send CMD12 when retuning one of my SD cards. [1] https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas-bsp.git/commit/?id=2838a2ff8ca776f6d18b7fbbe75f3df8dd64183aSigned-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: NJan Klötzke <jan.kloetzke@preh.de> Tested-by: NNguyen Viet Dung <dung.nguyen.aj@renesas.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Gustavo A. R. Silva 提交于
platform_get_irq() returns an error code, but the mxcmmc driver ignores it and always returns -EINVAL. This is not correct, and prevents -EPROBE_DEFER from being propagated properly. Print error message and propagate the return value of platform_get_irq on failure. Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Gustavo A. R. Silva 提交于
Local variable transfer_error is assigned to a constant value and it is never updated again. Remove this variable and the dead code it guards. Addresses-Coverity-ID: 1222110 Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Ivan Mikhaylov 提交于
shdci-st driver can be used for ppc476 fsp2 soc. Signed-off-by: NIvan Mikhaylov <ivan@de.ibm.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Will Newton 提交于
Reduce max_segs to 64, a value that allows allocation of an entire EDMA descriptor list within a single page - EDMA descriptors are 40 bytes and the header is much larger. This avoids doing a higher order GFP_ATOMIC allocation in edma_prep_slave_sg when setting up a transfer which can potentially fail due to fragmentation under heavy I/O load. The current value of 1024 is unusually high in comparison to other mmc host drivers which mostly use values of between 1 and 256. The EDMA driver at present splits lists above 20 segments in any case so reducing the size of lists we pass to it shouldn't add much overhead. Signed-off-by: NWill Newton <willn@resin.io> Acked-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Shawn Lin 提交于
Add "rockchip,rk3228-dw-mshc", "rockchip,rk3288-dw-mshc" for dwmmc on rk322x platform. Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com> Reviewed-by: NHeiko Stuebner <heiko@sntech.de> Acked-by: NRob Herring <robh@kernel.org> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Simon Horman 提交于
Add a new variant of the SDHI driver to support R-Car Gen3 with DMA via on-chip bus mastering. Since the DMAC is in a part of the SDHI module it is not suitable to be used via DMA Engine. Clearing of DM_CM_INFO1 after DMA thanks to Dirk Behme Cc: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NAi Kyuse <ai.kyuse.uw@renesas.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au> Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Simon Horman 提交于
Add dataend to DMA ops to allow DMAC implementation dependent handling of DMA data end. Also implement the operation for SDHI. Signed-off-by: NSimon Horman <horms+renesas@verge.net.au> Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Yoshihiro Shimoda 提交于
Allow TMIO and SDHI driver implementations to provide values for max_segs and max_blk_count. A follow-up patch will set these values for Renesas Gen3 SoCs the using an SDHI driver. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NAi Kyuse <ai.kyuse.uw@renesas.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au> Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Arvind Yadav 提交于
dev_pm_ops are not supposed to change at runtime. All functions working with dev_pm_ops provided by <linux/device.h> work with const dev_pm_ops. So mark the non-const structs as const. File size before: text data bss dec hex filename 11586 624 0 12210 2fb2 drivers/mmc/host/omap_hsmmc.o File size After adding 'const': text data bss dec hex filename 11778 432 0 12210 2fb2 drivers/mmc/host/omap_hsmmc.o Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
由 Arvind Yadav 提交于
clk_prepare_enable() can fail here and we must check its return value. Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
-
- 28 8月, 2017 8 次提交
-
-
由 Linus Torvalds 提交于
-
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu由 Linus Torvalds 提交于
Pull IOMMU fix from Joerg Roedel: "Another fix, this time in common IOMMU sysfs code. In the conversion from the old iommu sysfs-code to the iommu_device_register interface, I missed to update the release path for the struct device associated with an IOMMU. It freed the 'struct device', which was a pointer before, but is now embedded in another struct. Freeing from the middle of allocated memory had all kinds of nasty side effects when an IOMMU was unplugged. Unfortunatly nobody unplugged and IOMMU until now, so this was not discovered earlier. The fix is to make the 'struct device' a pointer again" * tag 'iommu-fixes-v4.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: iommu: Fix wrong freeing of iommu_device->dev
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc由 Linus Torvalds 提交于
Pull char/misc fix from Greg KH: "Here is a single misc driver fix for 4.13-rc7. It resolves a reported problem in the Android binder driver due to previous patches in 4.13-rc. It's been in linux-next with no reported issues" * tag 'char-misc-4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: ANDROID: binder: fix proc->tsk check.
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging由 Linus Torvalds 提交于
Pull staging/iio fixes from Greg KH: "Here are few small staging driver fixes, and some more IIO driver fixes for 4.13-rc7. Nothing major, just resolutions for some reported problems. All of these have been in linux-next with no reported problems" * tag 'staging-4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: iio: magnetometer: st_magn: remove ihl property for LSM303AGR iio: magnetometer: st_magn: fix status register address for LSM303AGR iio: hid-sensor-trigger: Fix the race with user space powering up sensors iio: trigger: stm32-timer: fix get trigger mode iio: imu: adis16480: Fix acceleration scale factor for adis16480 PATCH] iio: Fix some documentation warnings staging: rtl8188eu: add RNX-N150NUB support Revert "staging: fsl-mc: be consistent when checking strcmp() return" iio: adc: stm32: fix common clock rate iio: adc: ina219: Avoid underflow for sleeping time iio: trigger: stm32-timer: add enable attribute iio: trigger: stm32-timer: fix get/set down count direction iio: trigger: stm32-timer: fix write_raw return value iio: trigger: stm32-timer: fix quadrature mode get routine iio: bmp280: properly initialize device for humidity reading
-
git://github.com/jonmason/ntb由 Linus Torvalds 提交于
Pull NTB fixes from Jon Mason: "NTB bug fixes to address an incorrect ntb_mw_count reference in the NTB transport, improperly bringing down the link if SPADs are corrupted, and an out-of-order issue regarding link negotiation and data passing" * tag 'ntb-4.13-bugfixes' of git://github.com/jonmason/ntb: ntb: ntb_test: ensure the link is up before trying to configure the mws ntb: transport shouldn't disable link due to bogus values in SPADs ntb: use correct mw_count function in ntb_tool and ntb_transport
-
由 Linus Torvalds 提交于
The "lock_page_killable()" function waits for exclusive access to the page lock bit using the WQ_FLAG_EXCLUSIVE bit in the waitqueue entry set. That means that if it gets woken up, other waiters may have been skipped. That, in turn, means that if it sees the page being unlocked, it *must* take that lock and return success, even if a lethal signal is also pending. So instead of checking for lethal signals first, we need to check for them after we've checked the actual bit that we were waiting for. Even if that might then delay the killing of the process. This matches the order of the old "wait_on_bit_lock()" infrastructure that the page locking used to use (and is still used in a few other areas). Note that if we still return an error after having unsuccessfully tried to acquire the page lock, that is ok: that means that some other thread was able to get ahead of us and lock the page, and when that other thread then unlocks the page, the wakeup event will be repeated. So any other pending waiters will now get properly woken up. Fixes: 62906027 ("mm: add PageWaiters indicating tasks are waiting for a page bit") Cc: Nick Piggin <npiggin@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Jan Kara <jack@suse.cz> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Andi Kleen <ak@linux.intel.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Linus Torvalds 提交于
Tim Chen and Kan Liang have been battling a customer load that shows extremely long page wakeup lists. The cause seems to be constant NUMA migration of a hot page that is shared across a lot of threads, but the actual root cause for the exact behavior has not been found. Tim has a patch that batches the wait list traversal at wakeup time, so that we at least don't get long uninterruptible cases where we traverse and wake up thousands of processes and get nasty latency spikes. That is likely 4.14 material, but we're still discussing the page waitqueue specific parts of it. In the meantime, I've tried to look at making the page wait queues less expensive, and failing miserably. If you have thousands of threads waiting for the same page, it will be painful. We'll need to try to figure out the NUMA balancing issue some day, in addition to avoiding the excessive spinlock hold times. That said, having tried to rewrite the page wait queues, I can at least fix up some of the braindamage in the current situation. In particular: (a) we don't want to continue walking the page wait list if the bit we're waiting for already got set again (which seems to be one of the patterns of the bad load). That makes no progress and just causes pointless cache pollution chasing the pointers. (b) we don't want to put the non-locking waiters always on the front of the queue, and the locking waiters always on the back. Not only is that unfair, it means that we wake up thousands of reading threads that will just end up being blocked by the writer later anyway. Also add a comment about the layout of 'struct wait_page_key' - there is an external user of it in the cachefiles code that means that it has to match the layout of 'struct wait_bit_key' in the two first members. It so happens to match, because 'struct page *' and 'unsigned long *' end up having the same values simply because the page flags are the first member in struct page. Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Kan Liang <kan.liang@intel.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Christopher Lameter <cl@linux.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Linus Torvalds 提交于
We have a MAX_LFS_FILESIZE macro that is meant to be filled in by filesystems (and other IO targets) that know they are 64-bit clean and don't have any 32-bit limits in their IO path. It turns out that our 32-bit value for that limit was bogus. On 32-bit, the VM layer is limited by the page cache to only 32-bit index values, but our logic for that was confusing and actually wrong. We used to define that value to (((loff_t)PAGE_SIZE << (BITS_PER_LONG-1))-1) which is actually odd in several ways: it limits the index to 31 bits, and then it limits files so that they can't have data in that last byte of a page that has the highest 31-bit index (ie page index 0x7fffffff). Neither of those limitations make sense. The index is actually the full 32 bit unsigned value, and we can use that whole full page. So the maximum size of the file would logically be "PAGE_SIZE << BITS_PER_LONG". However, we do wan tto avoid the maximum index, because we have code that iterates over the page indexes, and we don't want that code to overflow. So the maximum size of a file on a 32-bit host should actually be one page less than the full 32-bit index. So the actual limit is ULONG_MAX << PAGE_SHIFT. That means that we will not actually be using the page of that last index (ULONG_MAX), but we can grow a file up to that limit. The wrong value of MAX_LFS_FILESIZE actually caused problems for Doug Nazar, who was still using a 32-bit host, but with a 9.7TB 2 x RAID5 volume. It turns out that our old MAX_LFS_FILESIZE was 8TiB (well, one byte less), but the actual true VM limit is one page less than 16TiB. This was invisible until commit c2a9737f ("vfs,mm: fix a dead loop in truncate_inode_pages_range()"), which started applying that MAX_LFS_FILESIZE limit to block devices too. NOTE! On 64-bit, the page index isn't a limiter at all, and the limit is actually just the offset type itself (loff_t), which is signed. But for clarity, on 64-bit, just use the maximum signed value, and don't make people have to count the number of 'f' characters in the hex constant. So just use LLONG_MAX for the 64-bit case. That was what the value had been before too, just written out as a hex constant. Fixes: c2a9737f ("vfs,mm: fix a dead loop in truncate_inode_pages_range()") Reported-and-tested-by: NDoug Nazar <nazard@nazar.ca> Cc: Andreas Dilger <adilger@dilger.ca> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Dave Kleikamp <shaggy@kernel.org> Cc: stable@kernel.org Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 27 8月, 2017 4 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input由 Linus Torvalds 提交于
Pull input fixes from Dmitry Torokhov: - a tweak to the IBM Trackpoint driver that helps recognizing trackpoints on never Lenovo Carbons - a fix to the ALPS driver solving scroll issues on some Dells - yet another ACPI ID has been added to Elan I2C toucpad driver - quieted diagnostic message in soc_button_array driver * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: ALPS - fix two-finger scroll breakage in right side on ALPS touchpad Input: soc_button_array - silence -ENOENT error on Dell XPS13 9365 Input: trackpoint - add new trackpoint firmware ID Input: elan_i2c - add ELAN0602 ACPI ID to support Lenovo Yoga310
-
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci由 Linus Torvalds 提交于
Pull PCI fix from Bjorn Helgaas: "Remove needlessly alarming MSI affinity warning (this is not actually a bug fix, but the warning prompts unnecessary bug reports)" * tag 'pci-v4.13-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI/MSI: Don't warn when irq_create_affinity_masks() returns NULL
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull x86 fixes from Ingo Molnar: "Two fixes: one for an ldt_struct handling bug and a cherry-picked objtool fix" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/mm: Fix use-after-free of ldt_struct objtool: Fix '-mtune=atom' decoding support in objtool 2.0
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull timer fix from Ingo Molnar: "Fix a timer granularity handling race+bug, which would manifest itself by spuriously increasing timeouts of some timers (from 1 jiffy to ~500 jiffies in the worst case measured) in certain nohz states" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: timers: Fix excessive granularity of new timers after a nohz idle
-
- 26 8月, 2017 7 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull perf fix from Ingo Molnar: "A single fix to not allow nonsensical event groups that result in kernel warnings" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/core: Fix group {cpu,task} validation
-
由 Linus Torvalds 提交于
Merge misc fixes from Andrew Morton: "6 fixes" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: mm/memblock.c: reversed logic in memblock_discard() fork: fix incorrect fput of ->exe_file causing use-after-free mm/madvise.c: fix freeing of locked page with MADV_FREE dax: fix deadlock due to misaligned PMD faults mm, shmem: fix handling /sys/kernel/mm/transparent_hugepage/shmem_enabled PM/hibernate: touch NMI watchdog when creating snapshot
-
git://git.kernel.org/pub/scm/virt/kvm/kvm由 Linus Torvalds 提交于
Pull Paolo Bonzini: "Bugfixes for x86, PPC and s390" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: PPC: Book3S: Fix race and leak in kvm_vm_ioctl_create_spapr_tce() KVM, pkeys: do not use PKRU value in vcpu->arch.guest_fpu.state KVM: x86: simplify handling of PKRU KVM: x86: block guest protection keys unless the host has them enabled KVM: PPC: Book3S HV: Add missing barriers to XIVE code and document them KVM: PPC: Book3S HV: Workaround POWER9 DD1.0 bug causing IPB bit loss KVM: PPC: Book3S HV: Use msgsync with hypervisor doorbells on POWER9 KVM: s390: sthyi: fix specification exception detection KVM: s390: sthyi: fix sthyi inline assembly
-
git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost由 Linus Torvalds 提交于
Pull virtio fixes from Michael Tsirkin: "Fixes two obvious bugs in virtio pci" * tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: virtio_pci: fix cpu affinity support virtio_blk: fix incorrect message when disk is resized
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux由 Linus Torvalds 提交于
Pull powerpc fix from Michael Ellerman: "Just one fix, to add a barrier in the switch_mm() code to make sure the mm cpumask update is ordered vs the MMU starting to load translations. As far as we know no one's actually hit the bug, but that's just luck. Thanks to Benjamin Herrenschmidt, Nicholas Piggin" * tag 'powerpc-4.13-8' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/mm: Ensure cpumask update is ordered
-
git://linux-nfs.org/~bfields/linux由 Linus Torvalds 提交于
Pull nfsd fixes from Bruce Fields: "Two nfsd bugfixes, neither 4.13 regressions, but both potentially serious" * tag 'nfsd-4.13-2' of git://linux-nfs.org/~bfields/linux: net: sunrpc: svcsock: fix NULL-pointer exception nfsd: Limit end of page list when decoding NFSv4 WRITE
-
git://git.samba.org/sfrench/cifs-2.6由 Linus Torvalds 提交于
Pull cifs fixes from Steve French: "Some bug fixes for stable for cifs" * tag 'cifs-fixes-for-4.13-rc6-and-stable' of git://git.samba.org/sfrench/cifs-2.6: cifs: return ENAMETOOLONG for overlong names in cifs_open()/cifs_lookup() cifs: Fix df output for users with quota limits
-