The commit 278b2083
(bonding: initial RCU conversion) has convert the roundrobin,
active-backup, broadcast and xor xmit path to rcu protection,
the performance will be better for these mode, so this time,
convert xmit path for alb mode.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>
Cc: Nikolay Aleksandrov <nikolay@redhat.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 278b2083
(bonding: initial RCU conversion) has convert the roundrobin,
active-backup, broadcast and xor xmit path to rcu protection,
the performance will be better for these mode, so this time,
convert xmit path for 3ad mode.
Suggested-by: NNikolay Aleksandrov <nikolay@redhat.com>
Suggested-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NWang Yufen <wangyufen@huawei.com>
Cc: Nikolay Aleksandrov <nikolay@redhat.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mellanox ConnectX architecture is:  mlx4_core is the lower level
PCI driver which register on the PCI id, and protocol specific drivers
are depended on it: mlx4_en - for Ethernet and mlx4_ib for Infiniband.
NIC could have multiple ports which can change their type dynamically.
We use the request_module() call to load the relevant protocol driver
when needed: on loading time or at port type change event.
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean up warning added by commit fe6f700d "net/mlx4_core: Respond to
operation request by firmware".
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Small code cleanup:

1. change MLX4_DEV_CAP_FLAGS2_REASSIGN_MAC_EN to MLX4_DEV_CAP_FLAG2_REASSIGN_MAC_EN

2. put MLX4_SET_PORT_PRIO2TC and MLX4_SET_PORT_SCHEDULER in the same union with the
   other MLX4_SET_PORT_yyy
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove code that triggers trivial build warnings.

drivers/net/ethernet/mellanox/mlx4/cmd.c: In function ‘mlx4_set_vf_vlan’:
drivers/net/ethernet/mellanox/mlx4/cmd.c:2256: warning: variable ‘vf_oper’ set but not used
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_map_sw_to_hw_steering_mode’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:648: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_map_sw_to_hw_steering_id’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:685: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_hw_rule_sz’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:712: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/fw.c: In function ‘mlx4_opreq_action’:
drivers/net/ethernet/mellanox/mlx4/fw.c:1732: warning: variable ‘type_m’ set but not used
drivers/net/ethernet/mellanox/mlx4/srq.c:302: warning: no previous prototype for ‘mlx4_srq_lookup’
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the version number of the driver.
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change brings support for 64 bit netstats to the driver. Previously
the stats were 64 bit but highly racy due to the fact that 64 bit
transactions are not atomic on 32 bit systems.  This change makes is so
that the 64 bit byte and packet stats are reliable on all architectures.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allocate the queue pairs individually instead of as a group.  This
allows for much easier queue management as it is possible to dynamically
resize the queues without having to free and allocate the entire block.

Ease statistic collection by treating Tx/Rx queue pairs as a single
unit.  Each pair is allocated together and starts with a Tx queue and
ends with an Rx queue.  By ordering them this way it is possible to know
the Rx offset based on a pointer to the Tx queue.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This replaces the ring container array with a linked list.  The idea is
to make the logic much easier to deal with since this will allow us to
call a simple helper function from the q_vectors to go through the
entire list.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allocate the q_vectors individually. The advantage to this is that it
allows for easier freeing and allocation.  In addition it makes it so
that we could do node specific allocations at some point in the future.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This makes it so that the Tx and Rx byte and packet counts are
separated from the rest of the statistics.  This allows for better
isolation of these stats when we move them into the 64 bit statistics.

Simplify things by re-ordering how the stats display in ethtool.
Instead of displaying all of the Tx queues as a block, followed by all
the Rx queues, the new order is Tx[0], Rx[0], Tx[1], Rx[1], ..., Tx[n],
Rx[n].  This reduces the loops and cleans up the display for testing
purposes since it is very easy to verify if flow director is doing the
right thing as the Tx and Rx queue pair are shown in pairs.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement BQL (byte queue limit) support in i40e.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Drop Tx flag and TXSW which is tested but never set.

As a result of this change we can drop a complicated check that always
resulted in the final result of i40e_tx_csum being equal to the
CHECKSUM_PARTIAL value.  As such we can replace the entire function call
with just a check for skb->summed == CHECKSUM_PARTIAL.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Sync the fast path for i40e_tx_map and i40e_clean_tx_irq so that they
are similar to igb and ixgbe.

- Only update the Tx descriptor ring in tx_map
- Make skb mapping always on the first buffer in the chain
- Drop the use of MAPPED_AS_PAGE Tx flag
- Only store flags on the first buffer_info structure
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Avoid directly incrementing next_to_use for multiple reasons.  The main
reason being that if we directly increment it then it can attain a state
where it is equal to the ring count.  Technically this is a state it
should not be able to reach but the way this is written it now can.

This patch pulls the value off into a register and then increments it
and writes back either the value or 0 depending on if the value is equal
to the ring count.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

- drop the mapped_as_page u8 from the Tx buffer info as it was unused
- use the DMA unmap accessors for Tx DMA
- replace checks of DMA with checks of the unmap length to verify if an
  unmap is needed
- update the Tx buffer layout to make it consistent with igb, ixgbe
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We can only setup multicast address for network device when
net_device_ops->ndo_set_rx_mode is not null.

Some configurations need to add multicast address for net
device, such as netfilter cluster match module.

Add a fake ndo_set_rx_mode function to allow this operation.
Signed-off-by: NGao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Tx "completed" stat was part of the original rewrite for detecting
Tx hangs.  However some time ago in ixgbe I determined that we could
just use the packets stat instead.  Since then this stat was
removed from ixgbe and it serves no purpose in i40e so it can be
dropped.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Link events should not print to the log until the device is
administratively up.
Signed-off-by: NAnjali Singhai <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SkyHawk-R can support RoCE. Add code to display RoCE specific
counters maintained in hardware.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moving to version 2 of GET_STATS command as SkyHawk-R supports
higher number of rings.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each network interface (either PF or VF) is identified by its port's MAC id.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 612c3373.

As per Stephen Hemminger, the layout of the netlink attribute
is not implemented correctly so revert this for now.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the missing destroy_workqueue() before return from
qlcnic_probe() in the error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fix the error handling in moxart_mac_probe():
 - return -ENOMEM in some memory alloc fail cases
 - add missing free_netdev() in the error handling case
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a guest is destroyed without transitioning its frontend to CLOSED,
the domain becomes a zombie as netback was not grant unmapping the
shared rings.

When removing a VIF, transition the backend to CLOSED so the VIF is
disconnected if necessary (which will unmap the shared rings etc).

This fixes a regression introduced by
279f438e (xen-netback: Don't destroy
the netdev until the vif is shut down).
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Paul Durrant <Paul.Durrant@citrix.com>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Reviewed-by: NPaul Durrant <paul.durrant@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a bug introduced by commit 51151a16 (mlx4: allow
order-0 memory allocations in RX path).

dma_unmap_page never reached because condition to detect last fragment
in page is wrong. offset+frag_stride can't be greater than size, need to
make sure no additional frag will fit in page => compare offset +
frag_stride + next_frag_size instead.
next_frag_size is the same as the current one, since page is shared only
with frags of the same size.

CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add page prefix to page related members: @size and @offset into
@page_size and @page_offset

CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, in TLB mode we change mac addresses only by memcpy-ing the to
net_device->dev_addr, without actually setting them via
dev_set_mac_address(). This permits us to receive all the traffic always on
one mac address.

However, in case the interface flips, some drivers might enforce the
mac filtering for its FW/HW based on current ->dev_addr, and thus we won't
be able to receive traffic on that interface, in case it will be selected
as active in TLB mode.

Fix it by setting the mac address forcefully on every new active slave that
we select in TLB mode.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Yuval Mintz <yuvalmin@broadcom.com>
Reported-by: NYuval Mintz <yuvalmin@broadcom.com>
Tested-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch will fix RX packets errors when receiving big size
of data by set bit RNC = 1.

RNC - Receive Enable Control

0: Upon completion of reception of one frame, the E-DMAC writes
the receive status to the descriptor and clears the RR bit in
EDRRR to 0.

1: Upon completion of reception of one frame, the E-DMAC writes
(writes back) the receive status to the descriptor. In addition,
the E-DMAC reads the next descriptor and prepares for reception
of the next frame.

In addition, for get more stable when receiving packets, I set
maximum size for the transmit/receive FIFO and inserts padding
in receive data.
Signed-off-by: NNguyen Hong Ky <nh-ky@jinso.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We play with a wait queue even if socket is
non blocking. This is an obvious waste.
Besides, it will prevent calling the non blocking
variant when current is not valid.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mrf24j40 generates level interrupts. There are rare cases where it
appears that the interrupt line never gets de-asserted between interrupts,
causing interrupts to be lost, and causing a hung device from the driver's
perspective.  Switching the driver to interpret these interrupts as
level-triggered fixes this issue.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eliminate all the workqueue and interrupt enable/disable.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This avoids a race condition where complete(tx_complete) could be called
before tx_complete is initialized.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip link has ability to show extra information of net work device if
kernel provides sunh information. With this patch veth driver can
provide its peer ifindex information to ip command via netlink
interface.
Signed-off-by: NMasatake YAMATO <yamato@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 4f0581d2.

The named changeset is causing problem. Let's aim to make this part less
fragile before trying to improve things.
Signed-off-by: NWei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Annie Li <annie.li@oracle.com>
Cc: Matt Wilson <msw@amazon.com>
Cc: Xi Xiong <xixiong@amazon.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the calculation of the nlmsg size, by adding the missing
nla_total_size().
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch proposes to remove the use of the IRQF_DISABLED flag

It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>