Reappearing channel paths are sometimes not utilized by CCW devices
because path verification incorrectly relies on path-operational-mask
information which is not updated until a channel path has been used
again.
Modify path verification procedure to always query all available paths
to a device.
Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

CHPIDs that are logically varied off will not be removed from
a CCW device's path group because resign-from-pathgroup command is
issued with invalid path mask of 0 because internal CCW operations
are masked by the logical path mask after the relevant bits are
cleared by the vary operation.
Do not apply logical path mask to internal operations.
Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Subchannel may incorrectly remain in state no-path after channel paths
have reappeared. Currently the scan for subchannels which are using a
channel path ends at the first occurrence if a full link address was
provided by the channel subsystem. The scan needs to continue over
all subchannels.
Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Specifying kernel parameter "dasd=nopav" on systems running under VM
has no function but results in message "disable PAV mode". Correct
message is "'nopav' not supported on VM".
Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add the MODALIAS environment variable for ccw bus uevents.
Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This introduces new user-copy operations which are optimized for
copying more than 256 Bytes on new hardware.
Signed-off-by: NGerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Introduces a struct uaccess_ops which allows setting user-copy
operations at run-time.
Signed-off-by: NGerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NGerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Changed and simplified some page table related #defines and code.
Signed-off-by: NGerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch delivers a new Linux API in the form of a misc char
device that is useable from user space and allows write access
to the z/VM APPLDATA Monitor Records collected by the *MONITOR
System Service of z/VM.
Signed-off-by: NMelissa Howland <melissah@us.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The xpram driver shows and uses 4096 bytes less than available.
Signed-off-by: NChristian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Follow other architectures and remove kexec experimental flag.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Introduce asm header that contains the appldata data structures and
the diag inline assembly.
Signed-off-by: NGerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Fix comment typo in vmcp, it is z/VM and not v/VM.
Signed-off-by: NChristian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Substract the size of the initial stack frame from the correct
register. Otherwise we will end up in a program check loop.
Fix the offset into the save area as well.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The last SLSB has to be set to STATE_PROCESSING if we really want to
use the PROCESSING feature.
Signed-off-by: NFrank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Previous patch that was intended to reduce stack usage within common
i/o layer didn't consider implicit memset(..., 0, ...) used with the
initializations used before.
Add these missing memsets wherever it's not obvious that the
concerned memory region is zeroed. This should give the same semantics
as before.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Convert GET_IPL_DEVICE assembler macro to C function.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

With System z9 additional fields have been added to the output of the
store system information instruction. This patch adds the new model
information field and the alternate cpu capability fields to the
output of /proc/sysinfo. While we at it clean up the code as well.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Enhanced default DBF level to get most important messages
in debug feature files.
Signed-off-by: NHorst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The dasd_device_from_cdev function is called from interrupt context
to get the struct dasd_device associated with a ccw device. The
driver_data of the ccw device points to the dasd_devmap structure
which contains the pointer to the dasd_device structure. The lock
that protects the dasd_devmap structure is acquire with out irqsave.
To prevent the deadlock in dasd_device_from_cdev if it is called
from interrupt context the dependency to the dasd_devmap structure
needs to be removed. Let the driver_data of the ccw device point
to the dasd_device structure directly and use the ccw device lock
to protect the access.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

qdio_get_micros is supposed to return microseconds. The get_clock()
return value needs to be shifted by 12 to get to microseconds.
Signed-off-by: NFrank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Fix compile warning with some configurations:

arch/s390/mm/cmm.c:58: warning: 'cmm_strtoul' defined but not used

Originally cmm_strtoul was introduced because simple_strtoul couldn't
handle strings with hexadecimal numbers that contained a capital 'X'.
Since this is no longer true cmm_strtoul can be removed.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add Heiko Carstens as co-maintainer for the s390 architecture.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Avoid using #undef in unistd.h.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

If do_signal() gets called several times before returning to user space
and no signal is pending (e.g. cancelled by a debugger) syscall restart
handling could be done several times. This would change the user space
PSW to an address prior to the syscall instruction.
Fix this by making sure that syscall restart handling is only done once.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Use do { } while (0) constructs instead of empty defines to avoid
subtle compile bugs.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

It is now possible to specify a ccw/fcp dump device which is used to
automatically create a system dump in case of a kernel panic. The dump
device can be configured under /sys/firmware/dump.
In addition it is now possible to specify a ccw/fcp device which is used
for the next reboot of Linux. The reipl device can be configured under
/sys/firmware/reipl.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add casts to avoid compiler warnings.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Correct some comments in the hypervisor filesystem.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Move initrd if the bitmap of the bootmem allocator would overwrite it.
In addition this patch sets the default size and address of the initrd to 0.
Therefore all boot loaders must set the initrd size and address correctly.
This is especially relevant for ftp boot via HMC/SE, where this change
requires a special patch file entry in the .ins file which sets these two
values contained at address 0x10408 and 0x10410.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NMichael Grundy <grundym@us.ibm.com>
Signed-off-by: NDavid Wilder <dwilder@us.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Allow the user space to send extended cprb messages directly to the
PCIXCC / CEX2C cards. This allows the CCA library to construct special
crypto requests that use "secure" keys that are stored on the card.
Signed-off-by: NRalph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The Makefile and Kconfig changes should be obvious. The monolithic
build option is there to create an old-style z90crypt module for
backward compatability to older distributions.
Signed-off-by: NRalph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NRalph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NRalph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The user space interface of the zcrypt device driver implements the old
user space interface as defined by the old z90crypt driver. Everything
is there, the /dev/z90crypt misc character device, all the lovely ioctls
and the /proc file. Even writing to the z90crypt proc file to configure
the crypto device still works. It stands to reason to remove the proc
write function someday since a much cleaner configuration via the sysfs
is now available.

The ap bus device drivers register crypto cards to the zcrypt user
space interface. The request router of the user space interface
picks one of the registered cards based on the predicted latency
for the request and calls the driver via a callback found in the
zcrypt_ops of the device. The request router only knows which
operations the card can do and the minimum / maximum number of bits
a request can have.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NRalph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add a bus for the adjunct processor interface. Up to 64 devices can
be connect to the ap bus interface, each device with 16 domains. That
makes 1024 message queues. The interface is asynchronous, the answer
to a message sent to a queue needs to be received at some later point
in time. Unfortunately the interface does not provide interrupts when
a message reply is pending. So the ap bus needs to implement some
fancy polling, each active queue is polled once per 1/HZ second or
continuously if an idle cpus exsists and the poll thread is activ
(see poll_thread parameter).

The ap bus uses the sysfs path /sys/bus/ap and has two bus attributes,
ap_domain and config_time. The ap_domain selects one of the 16 domains
to be used for this system. This limits the maximum number of ap devices
to 64. The config_time attribute contains the number of seconds between
two ap bus scans to find new devices.

The ap bus uses the modalias entries of the form "ap:tN" to autoload
the ap driver for hardware type N. Currently known types are:
3 - PCICC, 4 - PCICA, 5 - PCIXCC, 6 - CEX2A and 7 - CEX2C.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NRalph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>