There exist chips with up to four mv643xx_eth silicon blocks but
only one external SMI (MII management) interface -- the SMI logic
of the first block is shared by all the blocks.

Handle this by allowing a per-port override of which
mv643xx_eth_shared's SMI registers (and spinlock) to use.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Acked-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

Make t_clk configurable via platform device data (with the current
hardcoded value, 133 MHz, being the default), as it varies across
different chip families.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Acked-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

Make it possible to pass mbus_dram_target_info to the mv643xx_eth
driver via the platform data, and make the mv643xx_eth driver
program the window registers based on this data if it is passed in.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

Move mv643xx_eth's static state (ethernet register block base address
and MII management interface spinlock) into a struct hanging off the
shared platform device.  This is necessary to support chips that
contain multiple mv643xx_eth silicon blocks.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Acked-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable network
platform drivers, to re-enable auto loading.

NOTE: didn't change drivers/net/fs_enet/fs_enet-main.c "old binding" support.
That looks problematic in the first place (it even uses the ancient "struct
device_driver" binding scheme for platform_bus!) and I suspect it will vanish
soonish when arch/powerpc rules the world.  Also, drivers/net/ne.c would have
needed more thought to sort out.

[akpm@linux-foundation.org: fix sgiseeq.c]
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

When there are multiple mv643xx_eth silicon blocks in the system,
don't print an initialisation message for each and every one of
them.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

Pass a struct mv643xx_private * to the register accessor functions,
as a preparation for having multiple mv643xx_eth silicon blocks.

(Since this causes some 80 column straddling, and the mv_ prefix
is useless anyway, rename mv_read to rdl and mv_write to wrl to
compensate.)
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

In error and warning printks, always report the netdevice name
instead of the port index (the latter has no meaning when there
are multiple mv643xx_eth silicon blocks in the system.)
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

Instead of identifying individual mv643xx ethernet ports by only
their port number, identify them by their struct mv643xx_private *,
as just a port number has no meaning when there are multiple
mv643xx_eth silicon blocks in the system.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

- Remove unused MV643XX_DEFAULT_[RT]X_QUEUE_SIZE definitions.
- Remove ETH_TARGET enum -- it isn't used anywhere in the driver,
  and isn't even valid for non-mv643xx chip models, as those use
  different MBUS target IDs.
- Clean up comment and control flow in mv643xx_eth_change_mtu().
- Use mp->dev instead of mp->mii.dev in mv643xx_eth_tx_timeout_task().
- Make mv643xx_eth_free_tx_descs() static.
- Remove overzealous NULL check in mv643xx_eth_start_xmit().
- Use symbolic NETDEV_TX_* constants in mv643xx_eth_start_xmit().
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

mv643xx_eth_start_xmit() should check mp->tx_desc_count only
inside the mp->lock spinlock.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

Robert P.J. Day proposed to use the macro FIELD_SIZEOF in replace of code
that matches its definition.

The modification was made using the following semantic patch
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@haskernel@
@@

#include <linux/kernel.h>

@depends on haskernel@
type t;
identifier f;
@@

- (sizeof(((t*)0)->f))
+ FIELD_SIZEOF(t, f)

@depends on haskernel@
type t;
identifier f;
@@

- sizeof(((t*)0)->f)
+ FIELD_SIZEOF(t, f)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The mv643xx_eth driver can be loaded as a platform device, as is done by
various Orion (ARM) based devices.  The driver needs to define a module
alias for the platform driver so udev will load it automatically.
Tested with Debian on a QNAP TS-209.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Marvell Orion system on chips have an integrated mv643xx MAC.  On these
little endian ARM devices mv643xx will oops when checksum offload is
enabled.  Swapping the byte order of the protocol and checksum solves this
problem.
Signed-off-by: NByron Bradley <byron.bbradley@gmail.com>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Manish Lachwani <mlachwani@mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Commit b9f2c044 replaced mv643xx_get_stats_count() with
mv643xx_get_sset_count(), but forgot to hook it up.

drivers/net/mv643xx_eth.c:2678: warning: mv643xx_get_sset_count defined but not used
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

We fixed checksum offload a while back.  Remove the note that
it doesn't work.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

Since drivers/net/mv643xx_eth.c is the only user of
drivers/net/mv643xx_eth.h, there's not much use in having the header
file as a separate file, so merge the header into the driver.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

Now that all register address and bit defines are in private
namespace (drivers/net/mv643xx_eth.h), we can safely remove the
MV643XX_ETH_ prefix to conserve horizontal space.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Acked-by: NTzachi Perelstein <tzachi@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

Start counting mv643xx_eth register addresses from zero, instead of
from 0x2000 (MV643XX_ETH_SHARED_REGS.)
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Acked-by: NTzachi Perelstein <tzachi@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

Allow Orion ARM platforms to use the mv643xx_eth driver.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Acked-by: NTzachi Perelstein <tzachi@marvell.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is nicer than the MAC_FMT stuff.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the operations
	get-tx-csum
	get-sg
	get-tso
	get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.

This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.

The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case.  Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.

[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We now have struct net_device_stats embedded in struct net_device,
and the default ->get_stats() hook does the obvious thing for us.

Run through drivers/net/* and remove the driver-local storage of
statistics, and driver-local ->get_stats() hook where applicable.

This was just the low-hanging fruit in drivers/net; plenty more drivers
remain to be updated.

[ Resolved conflicts with napi_struct changes and fix sunqe build
  regression... -DaveM ]
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDenis Cheng <crquan@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it.  The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.

[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.

In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.

The signature of the ->poll() call back goes from:

	int foo_poll(struct net_device *dev, int *budget)

to

	int foo_poll(struct napi_struct *napi, int budget)

The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract).  The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.

The napi_struct is to be embedded in the device driver private data
structures.

Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler.  Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.

With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.

Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.

[ Ported to current tree and all drivers converted.  Integrated
  Stephen's follow-on kerneldoc additions, and restored poll_list
  handling to the old style to fix mutual exclusion issues.  -DaveM ]
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver erroneously zeros dev->tx_queue_len, since
mp->tx_ring_size has not yet been initialized.  Actually,
the driver shouldn't modify tx_queue_len at all and should
leave the value set by alloc_etherdev(), currently 1000.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Commit 468d09f8 masked the "state"
interrupt (bit 20 of the cause register). This results in Radstone's
PPC7D repeatedly re-entering the interrupt routine, locking up the
board. The following patch returns the required handling for this
interrupt.
Signed-off-by: NMartyn Welch <martyn.welch@radstone.co.uk>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Reported by Corey Minyard <cminyard@mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There is no good reason for the asymmetry in the parameters of
eth_port_uc_addr_get() and eth_port_uc_addr_set().  Make them
symmetric.  Remove some gratuitous block comments while we're here.
Signed-off-by: NGabriel Paubert <paubert@iram.es>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One less thing for drivers writers to worry about.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this driver, the default ethernet address is first set by by calling
eth_port_uc_addr_get() which reads the relevant registers of the
corresponding port as initially set by firmware. However that function
used the port_num field accessed through the private area of net_dev
before it was set.

The result was that one board I have ended up with the unicast address
set to 00:00:00:00:00:00 (only port 1 is connected on this board). The
problem appeared after commit 84dd619e.

This patch fixes the bug by setting mp->port_num prior to calling
eth_port_uc_get_addr().
Signed-off-by: NGabriel Paubert <paubert@iram.es>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

mv643xx_eth_shutdown is needed for kexec.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>