The register of ttctrl.ttha describes like below:
- Internal TT Hub Address Representation
- RW
- Default = 0000000b
This field is used to match against the Hub Address field in QH & siTD
to determine if the packet is routed to the internal TT for directly
attached FS/LS devices. If the Hub Address in the QH or siTD does not
match this address then the packet will be broadcast on the High Speed
ports destined for a downstream High Speed hub with the address in the QH/siTD.

In silicon RTL, this entry only affects QH and siTD, and the hub.addr at
both QH and siTD are 0 in ehci core for chipidea (with hcd->has_tt = 1).

So, for QH, if the "usage_tt" flag at RTL is 0, set CI_HDRC_SET_NON_ZERO_TTHA
will not affect QH (with non-hs device); for siTD, set this flag
will change remaining space requirement for the last transaction from 1023
bytes to 188 bytes, it can increase the number of transactions within one
frame, ehci periodic schedule code will not queue the packet if the frame space
is full, so it is safe to set this flag for siTD.

With this flag, it can fix the problem Alan Stern reported below:
http://www.spinics.net/lists/linux-usb/msg123125.html
And may fix Michael Tessier's problem too.
http://www.spinics.net/lists/linux-usb/msg118679.html

CC: stern@rowland.harvard.edu
CC: michael.tessier@axiontech.ca
Signed-off-by: NPeter Chen <peter.chen@freescale.com>

The ehci_init_driver is used to initialize hcd APIs for each
ehci controller driver, it is designed to be called only one time
and before driver register is called. The current design will
cause ehci_init_driver is called multiple times at probe process,
it will cause hc_driver's initialization affect current running hcd.

We run out NULL pointer dereference problem when one hcd is started
by module_init, and the other is started by otg thread at SMP platform.
The reason for this problem is ehci_init_driver will do memory copy
for current uniform hc_driver, and this memory copy will do memset (as 0)
first, so when the first hcd is running usb_add_hcd, and the second
hcd may clear the uniform hc_driver's space (at ehci_init_driver),
then the first hcd will meet NULL pointer at the same time.

See below two logs:

LOG_1:
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.1: doesn't support gadget
Unable to handle kernel NULL pointer dereference at virtual address 00000014
pgd = 80004000
[00000014] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 108 Comm: kworker/u8:2 Not tainted 3.14.38-222193-g24b2734-dirty #25
Workqueue: ci_otg ci_otg_work
task: d839ec00 ti: d8400000 task.ti: d8400000
PC is at ehci_run+0x4c/0x284
LR is at _raw_spin_unlock_irqrestore+0x28/0x54
pc : [<8041f9a0>]    lr : [<8070ea84>]    psr: 60000113
sp : d8401e30  ip : 00000000  fp : d8004400
r10: 00000001  r9 : 00000001  r8 : 00000000
r7 : 00000000  r6 : d8419940  r5 : 80dd24c0  r4 : d8419800
r3 : 8001d060  r2 : 00000000  r1 : 00000001  r0 : 00000000
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c53c7d  Table: 1000404a  DAC: 00000015
Process kworker/u8:2 (pid: 108, stack limit = 0xd8400238)
Stack: (0xd8401e30 to 0xd8402000)
1e20:                                     d87523c0 d8401e48 66667562 d8419800
1e40: 00000000 00000000 d8419800 00000000 00000000 00000000 d84198b0 8040fcdc
1e60: 00000000 80dd320c d8477610 d8419c00 d803d010 d8419800 00000000 00000000
1e80: d8004400 00000000 d8400008 80431494 80431374 d803d100 d803d010 d803d1ac
1ea0: 00000000 80432428 804323d4 d803d100 00000001 80435eb8 80e0d0bc d803d100
1ec0: 00000006 80436458 00000000 d803d100 80e92ec8 80436f44 d803d010 d803d100
1ee0: d83fde00 8043292c d8752710 d803d1f4 d803d010 8042ddfc 8042ddb8 d83f3b00
1f00: d803d1f4 80042b60 00000000 00000003 00000001 00000001 80054598 d83f3b00
1f20: d8004400 d83f3b18 d8004414 d8400000 80e3957b 00000089 d8004400 80043814
1f40: d839ec00 00000000 d83fcd80 d83f3b00 800436e4 00000000 00000000 00000000
1f60: 00000000 80048f34 00000000 00000000 00000000 d83f3b00 00000000 00000000
1f80: d8401f80 d8401f80 00000000 00000000 d8401f90 d8401f90 d8401fac d83fcd80
1fa0: 80048e68 00000000 00000000 8000e538 00000000 00000000 00000000 00000000
1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<8041f9a0>] (ehci_run) from [<8040fcdc>] (usb_add_hcd+0x248/0x6e8)
[<8040fcdc>] (usb_add_hcd) from [<80431494>] (host_start+0x120/0x2e4)
[<80431494>] (host_start) from [<80432428>] (ci_otg_start_host+0x54/0xbc)
[<80432428>] (ci_otg_start_host) from [<80435eb8>] (otg_set_protocol+0xa4/0xd0)
[<80435eb8>] (otg_set_protocol) from [<80436458>] (otg_set_state+0x574/0xc58)
[<80436458>] (otg_set_state) from [<80436f44>] (otg_statemachine+0x408/0x46c)
[<80436f44>] (otg_statemachine) from [<8043292c>] (ci_otg_fsm_work+0x3c/0x190)
[<8043292c>] (ci_otg_fsm_work) from [<8042ddfc>] (ci_otg_work+0x44/0x1c4)
[<8042ddfc>] (ci_otg_work) from [<80042b60>] (process_one_work+0xf4/0x35c)
[<80042b60>] (process_one_work) from [<80043814>] (worker_thread+0x130/0x3bc)
[<80043814>] (worker_thread) from [<80048f34>] (kthread+0xcc/0xe4)
[<80048f34>] (kthread) from [<8000e538>] (ret_from_fork+0x14/0x3c)
Code: e5953018 e3530000 0a000000 e12fff33 (e5878014)

LOG_2:
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.1: doesn't support gadget
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = 80004000
[00000000] *pgd=00000000
In Online 00:00ternal e      Offline rror: Oops: 80000005 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 108 Comm: kworker/u8:2 Not tainted 3.14.38-02007-g24b2734-dirty #127
Workque Online 00:00ue: ci_o      Offline tg ci_otg_work
Online 00:00task: d8      Offline 39ec00 ti: d83ea000 task.ti: d83ea000
PC is at 0x0
LR is at usb_add_hcd+0x248/0x6e8
pc : [<00000000>]    lr : [<8040f644>]    psr: 60000113
sp : d83ebe60  ip : 00000000  fp : d8004400
r10: 00000001  r9 : 00000001  r8 : d85fd4b0
r7 : 00000000  r6 : 00000000  r5 : 00000000  r4 : d85fd400
r3 : 00000000  r2 : d85fd4f4  r1 : 80410178  r0 : d85fd400
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c53c7d  Table: 1000404a  DAC: 00000015
Process kworker/u8:2 (pid: 108, stack limit = 0xd83ea238)
Stack: (0xd83ebe60 to 0xd83ec000)
be60: 00000000 80dd920c d8654e10 d85fd800 d803e010 d85fd400 00000000 00000000
be80: d8004400 00000000 d83ea008 80430e34 80430d14 d803e100 d803e010 d803e1ac
bea0: 00000000 80431dc8 80431d74 d803e100 00000001 80435858 80e130bc d803e100
bec0: 00000006 80435df8 00000000 d803e100 80e98ec8 804368e4 d803e010 d803e100
bee0: d86e8100 804322cc d86cf050 d803e1f4 d803e010 8042d79c 8042d758 d83cf900
bf00: d803e1f4 80042b78 00000000 00000003 00000001 00000001 800545e8 d83cf900
bf20: d8004400 d83cf918 d8004414 d83ea000 80e3f57b 00000089 d8004400 8004382c
bf40: d839ec00 00000000 d8393780 d83cf900 800436fc 00000000 00000000 00000000
bf60: 00000000 80048f50 80e019f4 00000000 0000264c d83cf900 00000000 00000000
bf80: d83ebf80 d83ebf80 00000000 00000000 d83ebf90 d83ebf90 d83ebfac d8393780
bfa0: 80048e84 00000000 00000000 8000e538 00000000 00000000 00000000 00000000
bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 ee66e85d 133ebd03
[<804 Online 00:000f644>]       Offline (usb_add_hcd) from [<80430e34>] (host_start+0x120/0x2e4)
[<80430e34>] (host_start) from [<80431dc8>] (ci_otg_start_host+0x54/0xbc)
[<80431dc8>] (ci_otg_start_host) from [<80435858>] (otg_set_protocol+0xa4/0xd0)
[<80435858>] (otg_set_protocol) from [<80435df8>] (otg_set_state+0x574/0xc58)
[<80435df8>] (otg_set_state) from [<804368e4>] (otg_statemachine+0x408/0x46c)
[<804368e4>] (otg_statemachine) from [<804322cc>] (ci_otg_fsm_work+0x3c/0x190)
[<804322cc>] (ci_otg_fsm_work) from [<8042d79c>] (ci_otg_work+0x44/0x1c4)
[<8042d79c>] (ci_otg_work) from [<80042b78>] (process_one_work+0xf4/0x35c)
[<80042b78>] (process_one_work) from [<8004382c>] (worker_thread+0x130/0x3bc)
[<8004382c>] (worker_thread) from [<80048f50>] (kthread+0xcc/0xe4)
[<80048f50>] (kthread) from [<8000e538>] (ret_from_fork+0x14/0x3c)
Code: bad PC value

Cc: Jun Li <jun.li@freescale.com>
Cc: <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>

The Marvell 28nm HSIC PHY requires the port to be forced to HS mode after
the port power is applied. This is done using the test mode in the PORTSC
register.

As HSIC is always HS, this work-around should be safe to do with all HSIC
PHYs and has been tested on i.MX6S.
Signed-off-by: NRob Herring <robh@kernel.org>
Tested-by: NPeter Chen <Peter.Chen@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, ci_default_pdata is common to all instances of the driver and
gets modified by the core driver code. This is bad if there are multiple
instances of the device with different settings such as the phy type. Fix
this by making a copy of the default platform_data.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Peter Chen <Peter.Chen@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove unneeded semicolon.

The semantic patch that makes this change is available
in scripts/coccinelle/misc/semicolon.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>

A string written by the user may not be zero terminated.

sscanf may read memory beyond the buffer if no zero byte
is found.

For testing build with CONFIG_USB_CHIPIDEA=y, CONFIG_USB_CHIPIDEA_DEBUG=y.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>

Wrongly release mutex lock during otg_statemachine may result in re-enter
otg_statemachine, which is not allowed, we should do next state transtition
after previous one completed.

Fixes: 826cfe75 ("usb: chipidea: add OTG fsm operation functions implementation")
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: NLi Jun <jun.li@freescale.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since the required clock to access registers is gated off in low power mode,
add ci->in_lpm check before try to dump registers value.
Signed-off-by: NLi Jun <jun.li@freescale.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>

By pass pullup DP in OTG fsm mode when do gadget connect, to let it handled
by OTG state machine.

This patch can fix the problem you found with my HNP polling patchset after
below 3 patches introduced:
467a78c8 usb: chipidea: udc: apply new usb_udc_vbus_handler interface
628ef0d2 usb: udc: add usb_udc_vbus_handler
dfea9c94 usb: udc: store usb_udc pointer in struct usb_gadget

Problem:
- Connect USB cable and MicroAB cable between two boards
- Boot up two boards
- load g_mass_storage at B-device side, the enumeration will success,
and A will see a usb mass-storage device
- load g_mass_storage at A-device side, the problem has occurred, the
connection will be lost at the beginning, then connect again.

This patch is based on
commit eff933c1d3a2e046492b3dfc86db813856553a29
(chipidea: pci: make it depends on NOP_USB_XCEIV)
on branch peter-usb-dev of
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb.gitSigned-off-by: NLi Jun <jun.li@freescale.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>

After commit ba1aff67 (chipidea: pci: register nop PHY) the PCI glue driver
requires nop-PHY to be selected. Thus, make it an explicit dependency.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Fixes: ba1aff67 (chipidea: pci: register nop PHY)
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch introduces USB_CHIPIDEA_PCI and USB_CHIPIDEA_OF Kconfig options, one
per each specific glue driver. This is needed to provide different dependencies
they have.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Current otg fsm timers are using controller 1ms irq and count it, this patch
is to replace it with hrtimer solution, use one hrtimer for all otg timers.
Signed-off-by: NLi Jun <jun.li@freescale.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

B_DATA_PLS(data-line pulse time) and B_SSEND_SRP(session end to SRP init) are
also from OTG&EH 2.0 Specification and they are not chipidea specific.
Signed-off-by: NLi Jun <jun.li@freescale.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since BSV irq is enabled for B-device all the time, so B_SESS_VLD timer
is not required, and also no need to check BSV status when B_ASE0_BRST
timer timeout.
Signed-off-by: NLi Jun <jun.li@freescale.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/chipidea/usbmisc_imx.c:277:5-8: Unneeded variable: "ret". Return "0" on line 297

 Removes unneeded variable used to store return value.

Generated by: scripts/coccinelle/misc/returnvar.cocci

Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It can move all pullup/pulldown operation control to udc-core
through usb_gadget_connect/usb_gadget_disconnect according to
vbus status.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds runtime power management support for otg fsm mode, since
A-device in a_idle state cannot detect data pulse irq after suspended, here
enable wakeup by connection before suspend to make it can be resumed by DP;
and handle wakeup from that state like SRP.
Signed-off-by: NLi Jun <jun.li@freescale.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If CI_HDRC_TURN_VBUS_EARLY_ON is set, turn on vbus before adding hcd, so it
will not set reg_vbus of ehci_ci_priv, then vbus will not be handled by ehci core.
Signed-off-by: NLi Jun <jun.li@freescale.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some usb PHYs need power supply from vbus to make it work, eg mxs-phy, if
there is no vbus, USB PHY will not in correct state when the controller starts
to work, for host, this requires vbus should be turned on before setting port
power(PP) of ehci, to work with this kind of USB PHY design, this patch adds
a flag CI_HDRC_TURN_VBUS_EARLY_ON, can be checked by host driver to turn on
vbus while start host.
Signed-off-by: NLi Jun <jun.li@freescale.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since PHY for ChipIdea is optional (not all SoCs having PHY for ChipIdea should
be programmed), we register 'nop' PHY for platforms that do not have
programmable PHY.
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For chipidea, its resume sequence is not-EHCI compatible, see
below description for FPR at portsc. So in order to send SoF in
time for remote wakeup sequence(within 3ms), the RUN/STOP bit must
be set before the resume signal is ended, but the usb resume
code may run after resume signal is ended, so we had to set it
at suspend path.

Force Port Resume - RW. Default = 0b.
1= Resume detected/driven on port.
0=No resume (K-state) detected/driven on port.
Host mode:
Software sets this bit to one to drive resume signaling. The Controller sets this bit to '1' if
a J-to-K transition is detected while the port is in the Suspend state. When this bit
transitions to a '1' because a J-to-K transition is detected, the Port Change Detect bit in
the USBSTS register is also set to '1'. This bit will automatically change to '0' after the
resume sequence is complete. This behavior is different from EHCI where the controller
driver is required to set this bit to a '0' after the resume duration is timed in the driver.
Note that when the controller owns the port, the resume sequence follows the defined

sequence documented in the USB Specification Revision 2.0. The resume signaling
(Full-speed 'K') is driven on the port as long as this bit remains a '1'. This bit will remain
a '1' until the port has switched to idle. Writing a '0' has no affect because the port
controller will time the resume operation, clear the bit and the port control state switches
to HS or FS idle.
This field is '0' if Port Power(PP) is '0' in host mode.

This bit is not-EHCI compatible.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Chipidea: Set connect-at-fullspeed bit when entering host mode if CI_HDRC_FORCE_FULLSPEED is set in the platform data

PORTSC_PFSC is not set on entering host mode which means the USB OTG
controller will attempt to enumerate USB devices at high speed even when the
CI_HDRC_FORCE_FULLSPEED flag is set in the platform data.

This patch ensures it is set right before host mode operations begin if needed.
Signed-off-by: NDaniel Tang <dt.tangr@gmail.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NDaniel Tang <dt.tangr@gmail.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

At chipidea revision 2.40a, there is a below errata:

9000531823  B2-Medium  Adding a dTD to a Primed Endpoint May Not Get Recognized

Title: Adding a dTD to a Primed Endpoint May Not Get Recognized

Impacted Configuration: All device mode configurations.

Description:
There is an issue with the add dTD tripwire semaphore (ATDTW bit in USBCMD register)
that can cause the controller to ignore a dTD that is added to a primed endpoint.
When this happens, the software can read the tripwire bit and the status bit at '1'
even though the endpoint is unprimed.

After executing a dTD, the device controller endpoint state machine executes a final
read of the dTD terminate bit to check if the application added a dTD to the linked
list at the last moment. This read is done in the finpkt_read_latest_next_td (44) state.
After the read is performed, if the terminate bit is still set, the state machine moves
to unprime the endpoint. The decision to unprime the endpoint is done in the
checkqh_decision (59) state, based on the value of the terminate bit.
Before reaching the checkqh_decision state, the state machine traverses the
writeqhtd_status (57), writeqh_status (56), and release_prime_mask (42) states.
As shown in the waveform, the ep_addtd_tripwire_clr signal is not set to clear
the tripwire bit in these states.

Workaround:
The software must implement a periodic poll cycle, and check for each dTD
pending on execution (Active = 1), if the enpoint is primed. It can do this by reading
the corresponding bits in the ENDPTPRIME and ENDPTSTAT registers. If these bits are
read at 0, the software needs to re-prime the endpoint by writing 1 to the corresponding
bit in the ENDPTPRIME register. This can be done for every microframe, every frame or
with a larger interval, depending on the urgency of transfer execution for the application.
Tested-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Define ci_get_revision API to know the controller revision
information according to chipidea 1.1a, 2.0a and 2.5a spec.
Besides, add one entry at struct ci_hdrc to indicate revision
information, it can be used for adding different code for
revisions, eg kinds of errata.
Reviewed-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Using hw_write_id_reg and hw_read_id_reg to write and read identification
registers contents, they can be used to get controller information, change
some system configurations, and so on.
Reviewed-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Except the same process with earlier imx6, it has below two features:

- Choose which vbus voltage as vbus wakeup source
We choose B_SESSION_VALID as vbus wakeup source since when the system
goes to suspend, the vbus comparator can't compare the vbus voltage
for VBUS_VALID.

- Disable dp/dm (linestate) change as wakeup source at device mode
when the vbus is not there, we don't expect dp/dm change waking up
usb controller at this situation.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We need to do it for all otg capable controller, not only peripheral
featured otg capable controller, otherwise, the host-only role, but
otg capable controller may be responded by otg interrupt.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Enable USB as system wakeup source, and each platform needs to implement
imx_usbmisc_set_wakeup in usbmisc_imx.c to support.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The USB signal can be system wakeup source, this patch add the
support, for how to enable it, see Documentation/usb/chipidea.txt.
Since USB wakeup enable logic is vendor/platform specific, the
glue layer needs to implement it to support this feature.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add runtime pm support for imx, only imx6 series are supported and tested.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This API is used to enable/disable usb wakeup, only imx6 series are
added, since I don't have other imx hardware on hand. Other imx users
can add their API according to reference manual after testing.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add runtime power management support.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move struct imx_usbmisc_data NULL pointer judgement from caller to
each API, it can simplify the caller.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

All imx usb controller's non core registers uses the same clock gate with
core registers, the usbmisc_imx is the library for imx glue driver, the
glue keeps clock on when it calls usbmisc_imx API to change non-core register.

Besides, we will support runtime pm in the future, it also needs to
close this clock when the usb is not in use.

Philipp Zabel also verifies it at imx6q platform, see
http://www.spinics.net/lists/linux-usb/msg118491.html

Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It is meaningless the glue layer driver has its own platform flag
which is the same meaning with common platform flag.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some gadget driver (like uac1) will try to enable endpoint again even
the ep is not empty, it will cause the ep reset again and may affect
the dTD list which has already queued.

It returns -EBUSY immediately, and indicate the endpoint is in use.
In this way, the ep's behavior will not be affected, and the gadget
driver is also notified.

Cc: Xuebing Wang <xbing6@gmail.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds response to a_alt_hnp_support set feature request from legacy
A device, that is, B-device can provide a message to the user indicating that
the user needs to connect the B-device to an alternate port on the A-device.
A device sets this feature indicates to the B-device that it is connected
to an A-device port that is not capable of HNP, but that the A-device does have
an alternate port that is capable of HNP.

[Peter]
Without this patch, the OTG B device can't be enumerated on
non-HNP port at A device, see below log:
[    2.287464] usb 1-1: Dual-Role OTG device on non-HNP port
[    2.293105] usb 1-1: can't set HNP mode: -32
[    2.417422] usb 1-1: new high-speed USB device number 4 using ci_hdrc
[    2.460635] usb 1-1: Dual-Role OTG device on non-HNP port
[    2.466424] usb 1-1: can't set HNP mode: -32
[    2.587464] usb 1-1: new high-speed USB device number 5 using ci_hdrc
[    2.630649] usb 1-1: Dual-Role OTG device on non-HNP port
[    2.636436] usb 1-1: can't set HNP mode: -32
[    2.641003] usb usb1-port1: unable to enumerate USB device

Cc: stable <stable@vger.kernel.org>
Acked-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NLi Jun <b47624@freescale.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a follow up to the previously submitted commit cefa9a31 (ehci-pci:
disable for Intel MID platforms).

It includes the following changes:
- table and function are renamed to reflect this is not only about ChipIdea
- ChipIdea PCI driver (ci_hdrc_pci.c) gets the comment about the table in
  ehci-pci.c
- MIPS IDs removed from the list since it was discovered and tested on Intel
  MID platforms
Reviewed-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The gadget power property will be used at get_status request.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>