* remove #cpus from mpc8544ds.dts (not used anywhere else)
* remove memreserve from mpc8568mds.dts (not needed)
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This adds in the device tree source for the SBC8641D, based
largely on the mpc8641_hpcn.dts.  The biggest differences are
the lack of a complex IRQ mapping (since no Uli/i8259 cascade)
and the different layout of devices on the localbus node.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

1. Detect (and bail out on) more conditions that violate the
assumptions of the setup code -- we assume in such cases that the device
tree is correct and reflects what the firmware did.

2. The inbound memory mask calculation was wrong.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

- get rid of `model = "UCC"' in the ucc nodes
  It isn't used anywhere, so remove it. If we'll ever need something
  like this, we'll use compatible property instead.
- replace last occurrences of device-id with cell-index.
  Drivers are modified for backward compatibility's sake.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch modifies the Embedded Planet EP8248E device tree to reference the
SMC paramater RAM base register instead of the parameter RAM allocated by the
boot loader.

The cpm_uart driver will allocate parameter RAM itself, making the serial port
initialisation independent of the boot loader.

The patch adds the parameter RAM allocated by the boot loader in the CPM muram
node, making it available to the kernel.
Signed-off-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch relocates the buffer descriptors and the SMC parameter RAM at the
end of the first CPM muram chunk, as described in the device tree. This allows
device trees to stop excluding SMC parameter ram allocated by the boot loader
from the CPM muram node.
Signed-off-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds a new generic device tree processing function that retrieves
virtual reg addresses from the device tree to the bootwrapper code. It also
updates the bootwrapper code to use the new function.

dt_get_virtual_reg() retrieves the virtual reg addresses from the
"virtual-reg" property. If the property can't be found, it uses the "reg"
property and walks the tree to translate it to absolute addresses.
Signed-off-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add the device tree node for the DMA engine on 8544, publish
the device and enable the driver in the defconfig.
Signed-off-by: NSebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Now that we properly set the physical address in the program header of the
vmlinux ELF we can extract it to properly set the load and entry point for
u-boot uImages.  Before we always hard coded the load & entry point to 0.
However there are situations that the kernel may be built with a non-zero
physical address.

We use objdump to extract the PHDR.  We assume that there is only one
PHDR in the vmlinux of type LOAD.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The prpmc2800 platform requires a zImage formatted file with an
embedded dtb file.  Rename the requested boot image file to
dtbImage.prpmc2800.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Acked-by: NMark A. Greer <mgreer@mvista.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The mv643xx_eth driver is being modified to support multiple instances
of the ethernet silicon block on the same platform.  Each block contains
a single register bank containing the registers for up to three ports
interleaved within that bank.  This patch updates the PowerPC OF to
platform_device glue code to support multiple silicon blocks, each
with up to three ethernet ports.  The main difference is that we now
allow multiple mv64x60_shared platform_devices to be registered and
we provide each port platform_device with a pointer to its associated
shared platform_device.  The pointer will not be used until the
mv643xx_eth driver changes are committed.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Acked-by: NMark Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Remove several unused (or software config only) properties.
Rename marvel node to "system-controller".  Also, rename the
"block-index" property to "cell-index" to conform to current
practice.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Replace several device node absolute path lookups in the mv64x60
bootwrapper code with lookups by compatible or device_type
properties.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Acked-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Compatible names should refer to a specific version of the hardware,
without wildcards.  Change each instance of mv64x60 to mv64360, which
is the oldest version we currently support.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

After the conversion to dts v1 format, seeing the frequencies
in decimal made it obvious that some of them had been
incorrectly truncated.  This fixes them.  Note that the PCI
frequency comes from a different source and is documented
as 66MHz, so it was left at 66000000.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Acked-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Update the prpmc2800 DTS file to version 1 and add labels.
I verified that there was no change in the resulting dtb file.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch changes the "max-frame-size" property to 9000 for all gbit
enabled 4xx boards. All those ports generally support jumbo frames, so
let's give the user a chance to enable it.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch fixes some problems in the Canyonlands 460EX and Glacier 460GT
dts files:

- Add "mdio-device = <&EMAC0>" to all all EMAC's except for EMAC0 itself
  (the 460EX/GT only can access the PHY via the EMAC0 instance)
- Add TAH support to Canyonlands dts
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This gets the FEC ethernet driver working again on the lite5200
platform.

The FEC driver is also compatible with the MPC5200, not only with the
MPC5200B, so this adds a suitable entry to the driver's match list.
Furthermore this adds the settings for the PHY in the dts file for the
Lite5200.  Note, that this is not exactly the same as in the
Lite5200B, because the PHY is located at f0003000:01 for the 5200, and
at :00 for the 5200B.  This was tested on a Lite5200 and a Lite5200B,
both booted a kernel via tftp and mounted the root via nfs
successfully.
Signed-off-by: NRené Bürgel <r.buergel@unicontrol.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

DTS updates that fix booting problems on mpc5200-based boards:
- change to ethernet reg property
- addition of mdio and phy nodes
- removal of pci node (Motion-Pro board)

Other DTS updates:
- update i2c device tree nodes
- add lpb bus node and flash device (without partitions defined)
- add rtc i2c nodes
Signed-off-by: NMarian Balakowicz <m8@semihalf.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This target produces a flat binary rather than an ELF file,
fixes the entry point at the beginning of the image, and takes
a complete device tree with no fixups needed.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Call dtc from the Makefile instead of the wrapper script so that the dt
blobs can be generated with a simple make invocation.

Using this patch allows board ports to trigger automatic building of .dtb
files by adding them to the image-y target list.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Improve the debugging support of the PS3 bootwraper code:

 o Increase the size of the PS3 bootwrapper overlay from 256 to 512 bytes to
   allow for more debugging code in the overlay.
 o Use the dot symbol to set the size of __system_reset_overlay.  The
   assembler will then emit an error if the overlay code is too big.
 o Remove some unused instructions.
 o Update the text describing the PS3 bootwrapper overlay.
 o Add a check for null pointer writes.
 o Change hcall return value from s64.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

as prescribed in Documentation/powerpc/booting-without-of.txt.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces.  The patch fixes the wrong
type in dts.

This patch fixes USB malfunctioning on the MPC837xE-RDB boards.

Similar patch has been already applied for the MDS boards:

  commit 28b95885
  Author: Li Yang <leoli@freescale.com>
  Date:   Thu Mar 6 18:42:26 2008 +0800

      [POWERPC] 83xx: Fix wrong USB phy type in mpc837xmds dts
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add device tree file for Emerson KSI8560 board.
Signed-off-by: NAlexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add boot wrapper for Emerson KSI8560 board.
Signed-off-by: NAlexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds the L2 cache node to the Taishan 440GX dts file.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Currently Haleakala uses the Kilauea platform code. This patch adds
"haleakala" to the compatible property, in case later kernel versions
will introduce a Haleakala platform code.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The patch adds the Glacier dts. The Glacier is nearly identical to the
Canyonlands (460EX). Here the differences:

- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch adds TAH (TCP/IP Acceleration Hardware) support to the
taishan 440GX dts. It depends on the NEWEMAC/tah patch that adds the
compatible "ibm,tah" property to the matching table.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add the cuboot wrapper for the AMCC 440EP Yosemite board
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds a DTS file for the AMCC 440EP Yosemite board.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This dts source file for the AMCC 460EX Canyonlands evalutaion board
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch alters the bootwrapper for a number of machines (roubhly
all 4xx based cuboot or treeboot platforms) to use aliases instead of
the linux,network-index hack to work out which MAC address to attach
to which ethernet device node.

The now obsolete linux,network-index properties are removed from the
corresponding device trees.  This won't break backwards compatiblity,
because in cases where this fixup code is relevant, the device tree is
part of the kernel image.

The references to linux,network-index are removed from
booting-without-of.txt.  Not only is it now deprecated, but as a hack
applicable only when the device tree blob and fixup code were in the
same image, this property never belonged in booting-without-of.txt
which describes the interface between the kernel and firmware or
bootloaders which produce a device tree.  By the time the device tree
reaches the kernel, all the MAC addresses must be fully filled in.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The MDIO node in the lite5200b.dts file needs to also claim compatibility
with the older mpc5200 chip.  Otherwise the driver won't find the device.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The wrapper script didn't have entries for the TQM8540 board and the
SBC8548 or SBC8560 boards.  I've assumed that the TQM8540 console is
8250 based and not CPM based by looking at its defconfig.  There was
also a trailing * on the TQM8555 entry that I removed too.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The pattern substitution rules were failing when used with zImage-dtb
targets.  If zImage-dtb.initrd was selected, the pattern substitution
would generate "zImage.initrd-dtb" instead of "zImage-dtb.initrd" which
caused the build to fail.

This renames zImage-dtb to dtbImage to avoid the problem entirely.
By not using the zImage prefix then is no potential for namespace
collisions.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>