The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes, so the driver needs
to account for this in the udma_filter() method.  In order to achieve that, do
the following changes:

- install the method for all chips, not only HPT36x/370 and improve the code
  formatting by killing the extra tabs while at it;

- add to the end of the 'switch' statement in the method cases for HPT372[AN]
  and HPT374 chips upon which the known SATA cards are based;

- use hwif->ultra_mask as a default mask for the ide_dma_filter() method to
  behave correctly;

- move the HPT370[A] cases below the HPT36x case for consistency.

While at it, replace the explicit UltraDMA mode masks with ATA_UDMA* constants
all over the driver...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bob Ham <rah@bash.sh>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Make the SATA drive detection code from eighty_ninty_three() into inline
ide_dev_is_sata() helper fixing it along the way to be more strict while
checking word 80 for the reserved values...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

HPT374 BIOS seems to only save f_CNT register value for the function #0 before
re-tuning DPLL (that causes the driver to report obviously distorted f_CNT for
the function #1) -- fix this by always reading the saved f_CNT register value
from the function #0 in the driver's init_chipset() method.
While at it, introduce 'chip_type' for holding the 'struct hpt_info' field
of the same name and replace the structure assignment with memcpy()...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The driver erroneously "lets go" the mate IDE chip in init_setup_pdc20270()
when ide_setup_pci_devices() call succeeds -- fix this, and drop a couple of
useless assignments in this function while at it...

Bart: keep "findev" variable initialization to silence gcc
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The IDE core never marked the PCI IDE devices as being in use after succesfull
driver probe call (the devices were marked in use only while being probed), and
so was susceptible to issues caused by unsolicited PCI hotplug device removal.
So, add pci_dev_get() call to ide_scan_pcidev() and convert this function to
the kernel style, also dropping a bunch of useless curly braces from its caller,
ide_scan_pcibus() and somewhat beautifying printk() call there, while at it...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Currently the mpc8xx ide driver will only work on arch/ppc so only
allow it to be built there.  Also, killed a minor include that isn't
actually used by the driver.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata clear horkage on ata_dev_init()
  [libata, IDE] add new VIA bridge to VIA PATA drivers
  pata_it821x: fix lost interrupt with atapi devices
  Fix broken pata_via cable detection

dev->horkage should be cleared over device hotunplug/plug.  Clear it
in ata_dev_init().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJoseph Chan <josephchan@via.com.tw>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The earlier crash dump fix on x86_64 depended on patches in -mm which
are intended for post-2.6.23.  Without those, it broke the build when
it went into 2.6.23-rc5.

This changes the field references in ELF_CORE_COPY_REGS back to those
still used in mainline.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the case when an nmi gets stucks the endflag stays equal to zero.
This causes the busy looping on other cpus to continue, even though the
nmi test is done.

On my machine with out the change below the system would hang right
after check_nmi_watchdog().  The change below just sets endflag prior to
checking if the test was successful or not.
Signed-off-by: NDaniel Walker <dwalker@mvista.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The CLFLUSH for the modified code line in text_poke was supposed
to speed up CPU recovery. Unfortunately it seems to cause hangs
on some VIA C3s (at least on VIA Esther Model 10 Stepping 9)
Remove it.

Thanks to Stefan Becker for reporting/testing.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the NMI watchdog on Intel CoreDuo processor where the kernel would
get stuck during boot.  The issue is related to errata AE49, where the
PERFEVTSEL1 counter does not have a working enable bit.  Thus it is not
possible to use it for NMI.

The patch creates a dedicated wd_ops for CoreDuo which falls back to
using PERFEVTSEL0.  The other Intel processors supporting the
architectural PMU will keep on using PERFEVTSEL1 as this allows other
subsystems, such as perfmon, to use PERFEVTSEL0 for PEBS monitoring in
particular.  Bug initially reported by Daniel Walker.

AK: Added comments
Signed-off-by: NStephane Eranian <eranian@hpl.hp.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

fsid_source decided where to get the 'fsid' number to
return for a GETATTR based on the type of filehandle.
It can be from the device, from the fsid, or from the
UUID.

It is possible for the filehandle to be inconsistent
with the export information, so make sure the export information
actually has the info implied by the value returned by
fsid_source.
Signed-off-by: NNeil Brown <neilb@suse.de>
Cc: "Luiz Fernando N. Capitulino" <lcapitulino@gmail.com>
Signed-off-by: N"J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Recent changes in NFSd cause a directory which is mounted-on
to not appear properly when the filesystem containing it is exported.

*exp_get* now returns -ENOENT rather than NULL and when
  commit 5d3dbbea
removed the NULL checks, it didn't add a check for -ENOENT.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When PTRACE_SYSCALL was used and then PTRACE_DETACH is used, the
TIF_SYSCALL_TRACE flag is left set on the formerly-traced task.  This
means that when a new tracer comes along and does PTRACE_ATTACH, it's
possible he gets a syscall tracing stop even though he's never used
PTRACE_SYSCALL.  This happens if the task was in the middle of a system
call when the second PTRACE_ATTACH was done.  The symptom is an
unexpected SIGTRAP when the tracer thinks that only SIGSTOP should have
been provoked by his ptrace calls so far.

A few machines already fixed this in ptrace_disable (i386, ia64, m68k).
But all other machines do not, and still have this bug.  On x86_64, this
constitutes a regression in IA32 compatibility support.

Since all machines now use TIF_SYSCALL_TRACE for this, I put the
clearing of TIF_SYSCALL_TRACE in the generic ptrace_detach code rather
than adding it to every other machine's ptrace_disable.
Signed-off-by: NRoland McGrath <roland@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix "lost" interrupt problem when using dma with CD/DVD drives in some
configurations.  This problem can make installing linux from media
impossible for distro's that have switched to libata-only configurations.

The simple fix is to eliminate the use of dma for reading drive status, etc,
by checking the number of bytes to transferred.

This change will only affect the behavior of atapi devices, not disks.
There is more info at http://bugzilla.redhat.com/show_bug.cgi?id=242229
This patch is for 2.6.22.1
Signed-off-by: NJeff Norden <jnorden@math.tntech.edu>
Reviewed-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

via_do_set_mode overwrites 80-wire cable detection bits. Let's
preserve them.
Signed-off-by: NLaurent Riffard <laurent.riffard@free.fr>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Ocelot: remove remaining bits
  [MIPS] TLB: Fix instruction bitmasks
  [MIPS] R10000: Fix wrong test in dma-default.c
  [MIPS] Provide empty irq_enable_hazard definition for legacy and R1 cores.
  [MIPS] Sibyte: Remove broken dependency on EXPERIMENTAL from SIBYTE_SB1xxx_SOC.
  [MIPS] Kconfig: whitespace cleanup.
  [MIPS] PCI: Set need_domain_info if controller domain index is non-zero.
  [MIPS] BCM1480: Fix computation of interrupt mask address register.
  [MIPS] i8259: Add disable method.
  [MIPS] tty: add the new ioctls and definitions.

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c-algo-bit: Read block data bugfix
  i2c-pxa: Fix adapter number
  i2c-gpio: Fix adapter number

* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
  hwmon: End of I/O region off-by-one

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  [CRYPTO] blkcipher: Fix inverted test in blkcipher_get_spot
  [CRYPTO] blkcipher: Fix handling of kmalloc page straddling

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: fw-ohci: ignore failure of pci_set_power_state (fix suspend regression)

* 'for-linus' of git://www.linux-m32r.org/git/takata/linux-2.6_dev:
  m32r: Rename STI/CLI macros
  m32r: build fix of entry.S
  m32r: Separate syscall table from entry.S
  m32r: Cosmetic updates of arch/m32r/kernel/entry.S
  m32r: Exit ei_handler directly for no IRQ case or IPI operations
  m32r: Simplify ei_handler code
  m32r: Define symbols to unify platform-dependent ICU checks
  m32r: Move dot.gdbinit files
  m32r: Rearrange platform-dependent codes
  m32r: Add defconfig file for the usrv platform.
  m32r: Update defconfig files for 2.6.23-rc1
  m32r: Move defconfig files to arch/m32r/configs/

* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  sched: fix ideal_runtime calculations for reniced tasks
  sched: improve prev_sum_exec_runtime setting
  sched: simplify __check_preempt_curr_fair()
  sched: fix xtensa build warning
  sched: debug: fix sum_exec_runtime clearing
  sched: debug: fix cfs_rq->wait_runtime accounting
  sched: fix niced_granularity() shift
  sched: fix MC/HT scheduler optimization, without breaking the FUZZ logic.

* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
  [XFS] fix nasty quota hashtable allocation bug
  [XFS] fix sparse shadowed variable warnings
  [XFS] fix ASSERT and ASSERT_ALWAYS
  [XFS] Fix sparse warning in kmem_shake_allow
  [XFS] Fix sparse NULL vs 0 warnings
  [XFS] Set filestreams object timeout to something sane.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
  [x86 setup] Work around bug in Xen HVM

Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-Off-By: NThiemo Seufer <ths@networkno.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NMaxime Bizon <mbizon@freebox.fr>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Following a strict interpretation the empty definition of irq_enable_hazard
has always been a bug - but an intentional one because it didn't bite.
This has now changed, for uniprocessor kernels mm/slab.c:do_drain()

[...]
        on_each_cpu(do_drain, cachep, 1, 1);
        check_irq_on();
[...]

may be compiled into a mtc0 c0_status; mfc0 c0_status sequence resulting
in a back-to-back hazard.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Otherwise Kconfig will produce a nonsenical .config for a kernel that is
neither 32-bit nor 64-bit.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This fixes this little funny:

bigsur:/proc/bus/pci# ls -l
total 0
dr-xr-xr-x    2 root     root            0 Aug 28 19:31 00
dr-xr-xr-x    2 root     root            0 Aug 28 19:31 00
dr-xr-xr-x    2 root     root            0 Aug 28 19:31 01
dr-xr-xr-x    2 root     root            0 Aug 28 19:31 03
-r--r--r--    1 root     root            0 Aug 28 19:31 devices
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

  CC      arch/mips/sibyte/bcm1480/irq.o
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_mask_irq':
arch/mips/sibyte/bcm1480/irq.c:112: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:114: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_unmask_irq':
arch/mips/sibyte/bcm1480/irq.c:130: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:132: warning: cast to pointer from integer of different size
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

After 76d21601, the qemu NE2000 was
frequently producing WATCHDOG timeouts.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Same as all the others, just put in the constants for the existing kernel
code and termios2 structure
Signed-off-by: NAlan Cox <alan@redhat.com>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Previously, ibmebus derived a device's bus_id from its location code.
The location code is not guaranteed to be unique, so we might get bus_id
collisions if two devices share the same location code.  The OFDT
full_name, however, is unique, so we use that instead (truncating it
on the left if it is too long).
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

On PS3, A storage device may show up in the repository before the hypervisor
has finished probing:
  - If its type is not yet known, it shows up as PS3_DEV_TYPE_STOR_DUMMY,
  - If its regions are being probed, it shows up as having zero regions.
If any of these happen, consider the device not yet present.  The storage
probe thread will retry later.

This fixes the timing-dependent problem where a kernel booted from FLASH ROM
sometimes cannot find the hard disk.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>