Prepare and enable the clocks when the board indicates the pcie buses
will be used.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Some orion platforms can gate the XOR driver clock. If the clock
exisits, unable/disable it as appropriate.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Some orion platforms support gating of the clock. If the clock exists
enable/disbale it as appropriate.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Some orion devices can gate the SDIO clock. If the clock exists,
enable/disable it as appropriate.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Not all orion platforms can gate the clock, but if it does exist,
enable/disable it as appropriate.

v2: Fix the name of the clkdev entry.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Not all platforms support gating the clock, so it is not an error if
the clock does not exist. However, if it does exist, we should
enable/disable it as appropriate.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The Orion kirkwood chips have a gatable clock per SATA channel. Add
code to get and enable this clk if it exists.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Let the machine pass to the platform which clock is used by the uart.
Enable the clock and use clk_get_rate() to determine its rate.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Remove tclk from platform data.  This makes the platform data
structure empty, so remove it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The t_clk is moved from the shared part of the ethernet driver into
the per port section. Each port can have its own gated clock, which it
needs to enable/disable, as oppossed to there being one clock shared
by all ports. In practice, only kirkwood supports this at the moment.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Remove now redundant tclk from SPI platform data. This makes the platform
data empty, so remove it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add tclk as a fixed rate clock for all platforms. In addition, on
kirkwood, add a gated clock for most of the clocks which can be gated.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
[mturquette@linaro.org: removed redundant CLKDEV_LOOKUP from Kconfig]
[mturquette@linaro.org: removed redundant clk.h from mach-dove/common.c]
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Enable core cpuidle timekeeping and irq enabling and remove that
handling from this code.
Signed-off-by: NRobert Lee <rob.lee@linaro.org>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Reviewed-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: NJean Pihet <j-pihet@ti.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Move all dreamplug-specific code out of board-dt.c and into
board-dreamplug.c.  This way new boards that are added during the
conversion to fdt don't clutter up board-dt.c.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

We need to absorb kirkwood_init() into kirkwood_dt_init() so that as we
convert drivers, we can remove the platform call, eg
kirkwood_rtc_init().  This maintains compatibility with non-fdt
configurations because they still call kirkwood_init() in common.c.

As drivers are converted, we will reinstate the 'static' qualifier in
common.c.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

It is not used anywhere in the sound driver.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

__mem_pci is only used to enable readl/writel and friends. Just condition
this on readl being defined and remove all the __mem_pci defines.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Stephen Warren <swarren@nvidia.com>

This uart is the primary console for the dreamplug.  Removed
kirkwood_uart0_init() call from board-dt.c.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Initially, copied guruplug-setup.c and did s/guruplug/dreamplug/g.
Then, switched to SPI based NOR flash.

After talking to Arnd Bergman, chose an incremental approach to adding
devicetree support.  First, we use the dtb to tell us we are on the
dreamplug, then we gradually port over drivers.

Driver porting will start with the uart (see next patch), and progress
from there.  Possibly, spi/flash/partitions will be next.

When done, board-dt.c will no longer be dreamplug specific, and dt's can
be made for the other kirkwood boards.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.

CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Now that most platforms don't need disable_fiq and arch_ret_to_user
macros, we can remove the empty macros or empty entry-macro.S files.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NRyan Mallon <rmallon@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>

The patch "ARM: orion: Consolidate USB platform setup code.", commit
4fcd3f37 broke USB on TS-7800 and
other orion5x boards, because the wrong type of PHY was being passed
to the EHCI driver in the platform data. Orion5x needs EHCI_PHY_ORION
and all the others want EHCI_PHY_NA.

Allow the mach- code to tell the generic plat-orion code which USB PHY
enum to place into the platform data.

Version 2: Rebase to v3.3-rc2.
Reported-by: NAmbroz Bizjak <ambrop7@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NAmbroz Bizjak <ambrop7@gmail.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Patchset "ARM: orion: Refactor the MPP code common in the orion
platform" broke at least Orion5x based platforms. These platforms have
pins configured as GPIO when the selector is not 0x0. However the
common code assumes the selector is always 0x0 for a GPIO lines. It
then ignores the GPIO bits in the MPP definitions, resulting in that
Orion5x machines cannot correctly configure there GPIO lines.

The Fix removes the assumption that the selector is always 0x0.
In order that none GPIO configurations are correctly blocked,
Kirkwood and mv78xx0 MPP definitions are corrected to only set the
GPIO bits for GPIO configurations.

This third version, which does not contain any whitespace changes,
and is rebased on v3.3-rc2.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Acked-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Convert from pci_scan_bus() to pci_scan_root_bus() and remove root bus
resource fixups.  This fixes the problem of "early" and "header" quirks
seeing incorrect root bus resources.

CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite.  Remove arm_machine_restart() as this function
no longer does anything useful.

For samsung platforms, remove the include of mach/system-reset.h and
plat/system-reset.h from their respective mach/system.h headers as these
just define their arch_reset functions.  As a result, the s3c2410 and
plat-samsung system-reset.h files are no longer referenced, so remove
these files entirely.
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Hook these platforms restart code into the new restart hook rather than
using arch_reset().
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NMichael Walle <michael@walle.cc>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Use an getter function in plat-orion/addr-map.c to get the address map
structure, rather than pass it to drivers in the platform_data
structures. When the drivers are built for none orion platforms, a
dummy function is provided instead which returns NULL.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NMichael Walle <michael@walle.cc>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Move the *_mbus_dram_info structure into the orion platform and call it
orion_mbus_dram_info everywhere.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NMichael Walle <michael@walle.cc>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Compile tested on Dove, orion5x, mv78xx0. Boot tested on Kirkwood.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NMichael Walle <michael@walle.cc>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

The MPP12 is listed in the 6281 HW manual as output only but the iconnect
board from iomega is using it as GPIO (there's a button connected on it). So,
I'm adding a definition for the MPP12 as GPIO. As I've no informations about
this and which kirkwood are "affected", I'm adding a new #define instead of
modifying the current one for MPP12.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Recognize the Kirkwood 6282 revision A1 chip since products using
this chip are shipping now, such as the QNAP TS-x19P II devices.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Acked-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

The eSata SheevaPlug and QNAP TS-209 devices were removed from
mach-types due to naming mismatches between machine_is_xxx(), CONFIG_XXX
and MACH_TYPE_XXX.

This patch fixes those mismatches and adds the devices back into
mach-types.
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NJon Medhurst <tixy@yxit.co.uk>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>

A generic version should replace this later.
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>

This patch makes the cpuidle_states structure global (single copy)
instead of per-cpu. The statistics needed on per-cpu basis
by the governor are kept per-cpu. This simplifies the cpuidle
subsystem as state registration is done by single cpu only.
Having single copy of cpuidle_states saves memory. Rare case
of asymmetric C-states can be handled within the cpuidle driver
and architectures such as POWER do not have asymmetric C-states.

Having single/global registration of all the idle states,
dynamic C-state transitions on x86 are handled by
the boot cpu. Here, the boot cpu  would disable all the devices,
re-populate the states and later enable all the devices,
irrespective of the cpu that would receive the notification first.

Reference:
https://lkml.org/lkml/2011/4/25/83Signed-off-by: NDeepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: NTrinabh Gupta <g.trinabh@gmail.com>
Tested-by: NJean Pihet <j-pihet@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Acked-by: NArjan van de Ven <arjan@linux.intel.com>
Acked-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NLen Brown <len.brown@intel.com>