- 29 10月, 2013 16 次提交
-
-
由 Jacob Keller 提交于
ixgbe_napi_disable_all calls napi_disable on each queue, however the busy polling code introduced a local_bh_disable()d context around the napi_disable. The original author did not realize that napi_disable might sleep, which would cause a sleep while atomic BUG. In addition, on a single processor system, the ixgbe_qv_lock_napi loop shouldn't have to mdelay. This patch adds an ixgbe_qv_disable along with a new IXGBE_QV_STATE_DISABLED bit, which it uses to indicate to the poll and napi routines that the q_vector has been disabled. Now the ixgbe_napi_disable_all function will wait until all pending work has been finished and prevent any future work from being started. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com> Cc: Alexander Duyck <alexander.duyck@intel.com> Cc: Hyong-Youb Kim <hykim@myri.com> Cc: Amir Vadai <amirv@mellanox.com> Cc: Dmitry Kravkov <dmitry@broadcom.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
napi_disable uses an msleep() call to wait for outstanding napi work to be finished after setting the disable bit. It does not always sleep incase there was no outstanding work. This resulted in a rare bug in ixgbe_down operation where a napi_disable call took place inside of a local_bh_disable()d context. In order to enable easier detection of future sleep while atomic BUGs, this patch adds a might_sleep() call, so that every use of napi_disable during atomic context will be visible. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com> Cc: Alexander Duyck <alexander.duyck@intel.com> Cc: Hyong-Youb Kim <hykim@myri.com> Cc: Amir Vadai <amirv@mellanox.com> Cc: Dmitry Kravkov <dmitry@broadcom.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Joseph Gasparakis 提交于
This patch removes the burden from the NIC drivers to check if the vxlan driver is enabled in the kernel and also makes available the vxlan headrooms to them. Signed-off-by: NJoseph Gasparakis <joseph.gasparakis@intel.com> Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Zhi Yong Wu 提交于
Signed-off-by: NZhi Yong Wu <wuzhy@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Zhi Yong Wu 提交于
Signed-off-by: NZhi Yong Wu <wuzhy@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Zhi Yong Wu 提交于
Signed-off-by: NZhi Yong Wu <wuzhy@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Zhi Yong Wu 提交于
drivers/net/vxlan.c: In function ‘vxlan_sock_add’: drivers/net/vxlan.c:2298:11: warning: ‘sock’ may be used uninitialized in this function [-Wmaybe-uninitialized] drivers/net/vxlan.c:2275:17: note: ‘sock’ was declared here LD drivers/net/built-in.o Signed-off-by: NZhi Yong Wu <wuzhy@linux.vnet.ibm.com> Signed-off-by: NStephen Hemminger <stephen@networkplumber.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hannes Frederic Sowa 提交于
UFO as well as UDP_CORK do not respect IP_PMTUDISC_DO and IP_PMTUDISC_PROBE well enough. UFO enabled packet delivery just appends all frags to the cork and hands it over to the network card. So we just deliver non-DF udp fragments (DF-flag may get overwritten by hardware or virtual UFO enabled interface). UDP_CORK does enqueue the data until the cork is disengaged. At this point it sets the correct IP_DF and local_df flags and hands it over to ip_fragment which in this case will generate an icmp error which gets appended to the error socket queue. This is not reflected in the syscall error (of course, if UFO is enabled this also won't happen). Improve this by checking the pmtudisc flags before appending data to the socket and if we still can fit all data in one packet when IP_PMTUDISC_DO or IP_PMTUDISC_PROBE is set, only then proceed. We use (mtu-fragheaderlen) to check for the maximum length because we ensure not to generate a fragment and non-fragmented data does not need to have its length aligned on 64 bit boundaries. Also the passed in ip_options are already aligned correctly. Maybe, we can relax some other checks around ip_fragment. This needs more research. Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Dalton 提交于
The virtio_net driver's mergeable receive buffer allocator uses 4KB packet buffers. For MTU-sized traffic, SKB truesize is > 4KB but only ~1500 bytes of the buffer is used to store packet data, reducing the effective TCP window size substantially. This patch addresses the performance concerns with mergeable receive buffers by allocating MTU-sized packet buffers using page frag allocators. If more than MAX_SKB_FRAGS buffers are needed, the SKB frag_list is used. Signed-off-by: NMichael Dalton <mwdalton@google.com> Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
The code for privacy extentions is very mature, and making it configurable only gives marginal memory/code savings in exchange for obfuscation and hard to read code via CPP ifdef'ery. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Alexander Aring says: ==================== 6lowpan: trivial changes This patch series includes some trivial changes to prepare the 6lowpan stack for upcomming patch-series which mainly fix fragmentation according to rfc4944 and udp handling(which is currently broken). Changes since v3: - really fix intendation in patch 3/5 Changes since v2: - change intendation in patch 3/5 - fix typo in 5/5 unecessary -> unnecessary - add missing 6lowpan tag in cover-letter ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Aring 提交于
Signed-off-by: NAlexander Aring <alex.aring@gmail.com> Reviewed-by: NWerner Almesberger <werner@almesberger.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Aring 提交于
This patch removes the assignment of skb->dev. We don't need it here because we use the netdev_alloc_skb_ip_align function which already sets the skb->dev. Signed-off-by: NAlexander Aring <alex.aring@gmail.com> Reviewed-by: NWerner Almesberger <werner@almesberger.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Aring 提交于
This patch uses the netdev_alloc_skb instead dev_alloc_skb function and drops the seperate assignment to skb->dev. Signed-off-by: NAlexander Aring <alex.aring@gmail.com> Reviewed-by: NWerner Almesberger <werner@almesberger.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Aring 提交于
The err variable can only be zero in this case. Signed-off-by: NAlexander Aring <alex.aring@gmail.com> Reviewed-by: NWerner Almesberger <werner@almesberger.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Aring 提交于
Signed-off-by: NAlexander Aring <alex.aring@gmail.com> Reviewed-by: NWerner Almesberger <werner@almesberger.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 10月, 2013 13 次提交
-
-
由 wangweidong 提交于
Two if statements do the same work, we can merge them to one. And fix some typos. There is just code simplification, no functional changes. Signed-off-by: NWang Weidong <wangweidong1@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 wangweidong 提交于
kmem_cache_zalloc had set the allocated memory to zero. I think no need to initialize with 0. And move the comments to the function begin. Acked-by: NVlad Yasevich <vyasevich@gmail.com> Signed-off-by: NWang Weidong <wangweidong1@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 wangweidong 提交于
fix some typos Acked-by: NVlad Yasevich <vyasevich@gmail.com> Signed-off-by: NWang Weidong <wangweidong1@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
While investigating on a recent vxlan regression, I found veth was using a zero features set for vxlan tunnels. We have to segment GSO frames, copy the payload, and do the checksum. This patch brings a ~200% performance increase We probably have to add hw_enc_features support on other virtual devices. Signed-off-by: NEric Dumazet <edumazet@google.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Alexei reported a performance regression on vxlan, caused by commit 3347c960 "ipv4: gso: make inet_gso_segment() stackable" GSO vxlan packets were not properly segmented, adding IP fragments while they were not expected. Rename 'bool tunnel' to 'bool encap', and add a new boolean to express the fact that UDP should be fragmented. This fragmentation is triggered by skb->encapsulation being set. Remove a "skb->encapsulation = 1" added in above commit, as its not needed, as frags inherit skb->frag from original GSO skb. Reported-by: NAlexei Starovoitov <ast@plumgrid.com> Signed-off-by: NEric Dumazet <edumazet@google.com> Tested-by: NAlexei Starovoitov <ast@plumgrid.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
This reverts commit 4d961a10, reversing changes made to a00f6fcc. Revert bond locking changes, they cause regressions and Veaceslav Falico doesn't like how the commit messages were done at all. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sathya Perla 提交于
Includes: - ndo_busy_poll implementation - Locking between napi and busy_poll - Fix rx_post_starvation (replenish rx-queues in out-of-mememory scenario) logic to accomodate busy_poll. v2 changes: [Eric D.'s comment] call alloc_pages() with GFP_ATOMIC even in ndo_busy_poll context as it is not allowed to sleep. Signed-off-by: NSathya Perla <sathya.perla@emulex.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Ding Tianhong says: ==================== bonding: patchset for rcu use in bonding The slave list will add and del by bond_master_upper_dev_link() and bond_upper_dev_unlink(), which will call call_netdevice_notifiers(), even it is safe to call it in write bond lock now, but we can't sure that whether it is safe later, because other drivers may deal NETDEV_CHANGEUPPER in sleep way, so I didn't admit move the bond_upper_dev_unlink() in write bond lock. now the bond_for_each_slave only protect by rtnl_lock(), maybe use bond_for_each_slave_rcu is a good way to protect slave list for bond, but as a system slow path, it is no need to transform bond_for_each_slave() to bond_for_each_slave_rcu() in slow path, so in the patchset, I will remove the unused read bond lock for monitor function, maybe it is a better way, I will wait to accept any relay for it. Thanks for the Veaceslav Falico opinion. v2: add and modify commit for patchset and patch, it will be the first step for the whole patchset. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 dingtianhong 提交于
The bond slave list may change when the monitor is running, the slave list is no longer protected by bond->lock, only protected by rtnl lock(), so we have 3 ways to modify it: 1.add bond_master_upper_dev_link() and bond_upper_dev_unlink() in bond->lock, but it is unsafe to call call_netdevice_notifiers() in write lock. 2.remove unused bond->lock for monitor function, only use the existing rtnl lock(). 3.use rcu_read_lock() to protect it, of course, it will transform bond_for_each_slave to bond_for_each_slave_rcu() and performance is better, but in slow path, it is ignored. so I remove the bond->lock and move the rtnl lock to protect the whole monitor function. Signed-off-by: NDing Tianhong <dingtianhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 dingtianhong 提交于
The bond slave list may change when the monitor is running, the slave list is no longer protected by bond->lock, only protected by rtnl lock(), so we have 3 ways to modify it: 1.add bond_master_upper_dev_link() and bond_upper_dev_unlink() in bond->lock, but it is unsafe to call call_netdevice_notifiers() in write lock. 2.remove unused bond->lock for monitor function, only use the existing rtnl lock(). 3.use rcu_read_lock() to protect it, of course, it will transform bond_for_each_slave to bond_for_each_slave_rcu() and performance is better, but in slow path, it is ignored. so I remove the bond->lock and move the rtnl lock to protect the whole monitor function. Signed-off-by: NDing Tianhong <dingtianhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 dingtianhong 提交于
The bond slave list may change when the monitor is running, the slave list is no longer protected by bond->lock, only protected by rtnl lock(), so we have 3 ways to modify it: 1.add bond_master_upper_dev_link() and bond_upper_dev_unlink() in bond->lock, but it is unsafe to call call_netdevice_notifiers() in write lock. 2.remove unused bond->lock for monitor function, only use the existing rtnl lock(). 3.use rcu_read_lock() to protect it, of course, it will transform bond_for_each_slave to bond_for_each_slave_rcu() and performance is better, but in slow path, it is ignored. so I remove the bond->lock and add the rtnl lock to protect the whole monitor function. Signed-off-by: NDing Tianhong <dingtianhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 dingtianhong 提交于
The bond slave list may change when the monitor is running, the slave list is no longer protected by bond->lock, only protected by rtnl lock(), so we have 3 ways to modify it: 1.add bond_master_upper_dev_link() and bond_upper_dev_unlink() in bond->lock, but it is unsafe to call call_netdevice_notifiers() in write lock. 2.remove unused bond->lock for monitor function, only use the existing rtnl lock(). 3.use rcu_read_lock() to protect it, of course, it will transform bond_for_each_slave to bond_for_each_slave_rcu() and performance is better, but in slow path, it is ignored. so I remove the bond->lock and move the rtnl lock to protect the whole monitor function. Signed-off-by: NDing Tianhong <dingtianhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 dingtianhong 提交于
The bond slave list may change when the monitor is running, the slave list is no longer protected by bond->lock, only protected by rtnl lock(), so we have 3 ways to modify it: 1.add bond_master_upper_dev_link() and bond_upper_dev_unlink() in bond->lock, but it is unsafe to call call_netdevice_notifiers() in write lock. 2.remove unused bond->lock for monitor function, only use the existing rtnl lock(). 3.use rcu_read_lock() to protect it, of course, it will transform bond_for_each_slave to bond_for_each_slave_rcu() and performance is better, but in slow path, it is ignored. so I remove the bond->lock and move the rtnl lock to protect the whole monitor function. Signed-off-by: NDing Tianhong <dingtianhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 10月, 2013 6 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next由 David S. Miller 提交于
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates This series contains updates to igb, igbvf, i40e, ixgbe and ixgbevf. Dan Carpenter provides a patch for igbvf to fix a bug found by a static checker. If the new MTU is very large, then "new_mtu + ETH_HLEN + ETH_FCS_LEN" can wrap and the check on the next line can underflow. Wei Yongjun provides 2 patches, the first against igbvf adds a missing iounmap() before the return from igbvf_probe(). The second against i40e, removes the include <linux/version.h> because it is not needed. Carolyn provides a patch for igb to fix a call to set the master/slave mode for all m88 generation 2 PHY's and removes the call for I210 devices which do not need it. Stefan Assmann provides a patch for igb to fix an issue which was broke by: commit fa44f2f1 Author: Greg Rose <gregory.v.rose@intel.com> Date: Thu Jan 17 01:03:06 2013 -0800 igb: Enable SR-IOV configuration via PCI sysfs interface which breaks the reloading of igb when VFs are assigned to a guest, in several ways. Jacob provides a patch for ixgbe and ixgbevf. First, against ixgbe, cleans up ixgbe_enumerate_functions to reduce code complexity. The second, against ixgbevf, adds support for ethtool's get_coalesce and set_coalesce command for the ixgbevf driver. Yijing Wang provides a patch for ixgbe to use pcie_capability_read_word() to simplify the code. Emil provides a ixgbe patch to fix an issue where the logic used to detect changes in rx-usecs was incorrect and was masked by the call to ixgbe_update_rsc(). Don provides 2 patches for ixgbevf. First creates a new function to set PSRTYPE. The second bumps the ixgbevf driver version. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexei Starovoitov 提交于
commit 991fb3f7 "dev: always advertise rx_flags changes via netlink" introduced rtnl notification from __dev_set_promiscuity(), which can be called in atomic context. Steps to reproduce: ip tuntap add dev tap1 mode tap ifconfig tap1 up tcpdump -nei tap1 & ip tuntap del dev tap1 mode tap [ 271.627994] device tap1 left promiscuous mode [ 271.639897] BUG: sleeping function called from invalid context at mm/slub.c:940 [ 271.664491] in_atomic(): 1, irqs_disabled(): 0, pid: 3394, name: ip [ 271.677525] INFO: lockdep is turned off. [ 271.690503] CPU: 0 PID: 3394 Comm: ip Tainted: G W 3.12.0-rc3+ #73 [ 271.703996] Hardware name: System manufacturer System Product Name/P8Z77 WS, BIOS 3007 07/26/2012 [ 271.731254] ffffffff81a58506 ffff8807f0d57a58 ffffffff817544e5 ffff88082fa0f428 [ 271.760261] ffff8808071f5f40 ffff8807f0d57a88 ffffffff8108bad1 ffffffff81110ff8 [ 271.790683] 0000000000000010 00000000000000d0 00000000000000d0 ffff8807f0d57af8 [ 271.822332] Call Trace: [ 271.838234] [<ffffffff817544e5>] dump_stack+0x55/0x76 [ 271.854446] [<ffffffff8108bad1>] __might_sleep+0x181/0x240 [ 271.870836] [<ffffffff81110ff8>] ? rcu_irq_exit+0x68/0xb0 [ 271.887076] [<ffffffff811a80be>] kmem_cache_alloc_node+0x4e/0x2a0 [ 271.903368] [<ffffffff810b4ddc>] ? vprintk_emit+0x1dc/0x5a0 [ 271.919716] [<ffffffff81614d67>] ? __alloc_skb+0x57/0x2a0 [ 271.936088] [<ffffffff810b4de0>] ? vprintk_emit+0x1e0/0x5a0 [ 271.952504] [<ffffffff81614d67>] __alloc_skb+0x57/0x2a0 [ 271.968902] [<ffffffff8163a0b2>] rtmsg_ifinfo+0x52/0x100 [ 271.985302] [<ffffffff8162ac6d>] __dev_notify_flags+0xad/0xc0 [ 272.001642] [<ffffffff8162ad0c>] __dev_set_promiscuity+0x8c/0x1c0 [ 272.017917] [<ffffffff81731ea5>] ? packet_notifier+0x5/0x380 [ 272.033961] [<ffffffff8162b109>] dev_set_promiscuity+0x29/0x50 [ 272.049855] [<ffffffff8172e937>] packet_dev_mc+0x87/0xc0 [ 272.065494] [<ffffffff81732052>] packet_notifier+0x1b2/0x380 [ 272.080915] [<ffffffff81731ea5>] ? packet_notifier+0x5/0x380 [ 272.096009] [<ffffffff81761c66>] notifier_call_chain+0x66/0x150 [ 272.110803] [<ffffffff8108503e>] __raw_notifier_call_chain+0xe/0x10 [ 272.125468] [<ffffffff81085056>] raw_notifier_call_chain+0x16/0x20 [ 272.139984] [<ffffffff81620190>] call_netdevice_notifiers_info+0x40/0x70 [ 272.154523] [<ffffffff816201d6>] call_netdevice_notifiers+0x16/0x20 [ 272.168552] [<ffffffff816224c5>] rollback_registered_many+0x145/0x240 [ 272.182263] [<ffffffff81622641>] rollback_registered+0x31/0x40 [ 272.195369] [<ffffffff816229c8>] unregister_netdevice_queue+0x58/0x90 [ 272.208230] [<ffffffff81547ca0>] __tun_detach+0x140/0x340 [ 272.220686] [<ffffffff81547ed6>] tun_chr_close+0x36/0x60 Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com> Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hannes Frederic Sowa 提交于
We also can defer the initialization of hashrnd in flow_dissector to its first use. Since net_get_random_once is irq safe now we don't have to audit the call paths if one of this functions get called by an interrupt handler. Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hannes Frederic Sowa 提交于
I initial build non irq safe version of net_get_random_once because I would liked to have the freedom to defer even the extraction process of get_random_bytes until the nonblocking pool is fully seeded. I don't think this is a good idea anymore and thus this patch makes net_get_random_once irq safe. Now someone using net_get_random_once does not need to care from where it is called. Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nikolay Aleksandrov 提交于
I think that a dev_put() is needed in the error path to preserve the proper dev refcount. CC: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com> Acked-by: NVeaceslav Falico <vfalico@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hagen Paul Pfeifer 提交于
The transition from markov state "3 => lost packets within a burst period" to "1 => successfully transmitted packets within a gap period" has no *additional* loss event. The loss already happen for transition from 1 -> 3, this additional loss will make things go wild. E.g. transition probabilities: p13: 10% p31: 100% Expected: Ploss = p13 / (p13 + p31) Ploss = ~9.09% ... but it isn't. Even worse: we get a double loss - each time. So simple don't return true to indicate loss, rather break and return false. Signed-off-by: NHagen Paul Pfeifer <hagen@jauu.net> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Eric Dumazet <edumazet@google.com> Cc: Stefano Salsano <stefano.salsano@uniroma2.it> Cc: Fabio Ludovici <fabio.ludovici@yahoo.it> Signed-off-by: NHagen Paul Pfeifer <hagen@jauu.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 10月, 2013 5 次提交
-
-
由 Don Skidmore 提交于
Bump patch to reflect what version of the out of tree driver it has equivalent functionality with (2.11.3). Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
This patch adds support for ethtool's get_coalesce and set_coalesce command for the ixgbevf driver. This enables dynamically updating the minimum time between interrupts. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Don Skidmore 提交于
This patch creates a new function to set PSRTYPE. This function helps lay the ground work for eventual multi queue support. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Emil Tantilov 提交于
This patch resolves an issue where the logic used to detect changes in rx-usecs was incorrect and was masked by the call to ixgbe_update_rsc(). Setting rx-usecs between 0,2-9 and 1,10 and up requires a reset to allow ixgbe_configure_tx_ring() to set the correct value for TXDCTL.WTHRESH in order to avoid Tx hangs with BQL enabled. Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Yijing Wang 提交于
use pcie_capability_read_word() to simplify code. Signed-off-by: NYijing Wang <wangyijing@huawei.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-