If a system is idle from an RCU perspective for longer than specified
by CONFIG_RCU_CPU_STALL_TIMEOUT, and if one CPU starts a grace period
just as a second checks for CPU stalls, and if this second CPU happens
to see the old value of rsp->jiffies_stall, it will incorrectly report a
CPU stall.  This is quite rare, but apparently occurs deterministically
on systems with about 6TB of memory.

This commit therefore orders accesses to the data used to determine
whether or not a CPU stall is in progress.  Grace-period initialization
and cleanup first increments rsp->completed to mark the end of the
previous grace period, then records the current jiffies in rsp->gp_start,
then records the jiffies at which a stall can be expected to occur in
rsp->jiffies_stall, and finally increments rsp->gpnum to mark the start
of the new grace period.  Now, this ordering by itself does not prevent
false positives.  For example, if grace-period initialization was delayed
between recording rsp->gp_start and rsp->jiffies_stall, the CPU stall
warning code might still see an old value of rsp->jiffies_stall.

Therefore, this commit also orders the CPU stall warning accesses as
well, loading rsp->gpnum and jiffies, then rsp->jiffies_stall, then
rsp->gp_start, and finally rsp->completed.  This ordering means that
the false-positive scenario in the previous paragraph would result
in rsp->completed being greater than or equal to rsp->gpnum, which is
never valid for a CPU stall, allowing the false positive to be rejected.
Furthermore, any fetch that gets an old value of rsp->jiffies_stall
must also get an old value of rsp->gpnum, which will again be rejected
by the comparison of rsp->gpnum and rsp->completed.  Situations where
rsp->gp_start is later than rsp->jiffies_stall are also rejected, as
are situations where jiffies is less than rsp->jiffies_stall.

Although use of unsynchronized accesses means that there are likely
still some false-positive scenarios (synchronization has proven to be
a very bad idea on large systems), this should get rid of a large class
of these scenarios.
Reported-by: NFabian Herschel <fabian.herschel@suse.com>
Reported-by: NMichal Hocko <mhocko@suse.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: NMichal Hocko <mhocko@suse.cz>
Tested-by: NJochen Striepe <jochen@tolot.escape.de>

The for_each_rcu_flavor() loop unconditionally scans all flavors, even
when the first flavor might have some non-lazy callbacks.  Once the
loop has seen a non-lazy callback, further passes through the loop
cannot change the state.  This is not a huge problem, given that there
can be at most three RCU flavors (RCU-bh, RCU-preempt, and RCU-sched),
but this code is on the path to idle, so speeding it up even a small
amount would have some benefit.

This commit therefore does two things:

1.	Rearranges the order of the list of RCU flavors in order to
	place the most active flavor first in the list.  The most active
	RCU flavor is RCU-preempt, or, if there is no RCU-preempt,
	RCU-sched.

2.	Reworks the for_each_rcu_flavor() to exit early when the first
	non-lazy callback is seen, or, in the case where the caller
	does not care about non-lazy callbacks (RCU_FAST_NO_HZ=n),
	when the first callback is seen.
Reported-by: NChen Gang <gang.chen@asianux.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

The "idle" variable in both rcu_eqs_enter_common() and
rcu_eqs_exit_common() is only used in a WARN_ON_ONCE().  If the kernel
is built disabling WARN_ON_ONCE(), the compiler will complain (rightly)
that "idle" is unused.  This commit therefore adds a __maybe_unused to
the declaration of both variables.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

__get_cpu_var() is used for multiple purposes in the kernel source. One
of them is address calculation via the form &__get_cpu_var(x). This
calculates the address for the instance of the percpu variable of the
current processor based on an offset.

Other use cases are for storing and retrieving data from the current
processors percpu area.  __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.

__get_cpu_var() is defined as :

__get_cpu_var() always only does an address determination. However,
store and retrieve operations could use a segment prefix (or global
register on other platforms) to avoid the address calculation.

this_cpu_write() and this_cpu_read() can directly take an offset into
a percpu area and use optimized assembly code to read and write per
cpu variables.

This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations
that use the offset. Thereby address calcualtions are avoided and less
registers are used when code is generated.

At the end of the patchset all uses of __get_cpu_var have been removed
so the macro is removed too.

The patchset includes passes over all arches as well. Once these
operations are used throughout then specialized macros can be defined in
non -x86 arches as well in order to optimize per cpu access by f.e. using
a global register that may be set to the per cpu base.

Transformations done to __get_cpu_var()

1. Determine the address of the percpu instance of the current processor.

	DEFINE_PER_CPU(int, y);
	int *x = &__get_cpu_var(y);

    Converts to

	int *x = this_cpu_ptr(&y);

2. Same as #1 but this time an array structure is involved.

	DEFINE_PER_CPU(int, y[20]);
	int *x = __get_cpu_var(y);

    Converts to

	int *x = this_cpu_ptr(y);

3. Retrieve the content of the current processors instance of a per cpu
   variable.

	DEFINE_PER_CPU(int, u);
	int x = __get_cpu_var(y)

   Converts to

	int x = __this_cpu_read(y);

4. Retrieve the content of a percpu struct

	DEFINE_PER_CPU(struct mystruct, y);
	struct mystruct x = __get_cpu_var(y);

   Converts to

	memcpy(this_cpu_ptr(&x), y, sizeof(x));

5. Assignment to a per cpu variable

	DEFINE_PER_CPU(int, y)
	__get_cpu_var(y) = x;

   Converts to

	this_cpu_write(y, x);

6. Increment/Decrement etc of a per cpu variable

	DEFINE_PER_CPU(int, y);
	__get_cpu_var(y)++

   Converts to

	this_cpu_inc(y)
Signed-off-by: NChristoph Lameter <cl@linux.com>
[ paulmck: Address conflicts. ]
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

The list_splice_init_rcu() function allows a list visible to RCU readers
to be spliced into another list visible to RCU readers.  This is OK,
except for the use of INIT_LIST_HEAD(), which does pointer updates
without doing anything to make those updates safe for concurrent readers.

Of course, most of the time INIT_LIST_HEAD() is being used in reader-free
contexts, such as initialization or cleanup, so it is OK for it to update
pointers in an unsafe-for-RCU-readers manner.  This commit therefore
creates an INIT_LIST_HEAD_RCU() that uses ACCESS_ONCE() to make the updates
reader-safe.  The reason that we can use ACCESS_ONCE() instead of the more
typical rcu_assign_pointer() is that list_splice_init_rcu() is updating the
pointers to reference something that is already visible to readers, so
that there is no problem with pre-initialized values.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

This commit replaces an incorrect (but fortunately functional)
bitwise OR ("|") operator with the correct logical OR ("||").
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

The rcu_cpu_stall_timeout kernel parameter, the rcu_dynticks per-CPU
variable, and the rcu_gp_fqs() function are used only locally.  This
commit therefore marks them as static.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

One of the ->gp_flags assignments used a raw number rather than the
cpp macro that was intended for this purpose, which this commit fixes.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

There is a loop in do_mlockall() that lacks a preemption point, which
means that the following can happen on non-preemptible builds of the
kernel:

> My fuzz tester keeps hitting this. Every instance shows the non-irq stack
> came in from mlockall.  I'm only seeing this on one box, but that has more
> ram (8gb) than my other machines, which might explain it.
>
> 	Dave
>
> INFO: rcu_preempt self-detected stall on CPU { 3}  (t=6500 jiffies g=470344 c=470343 q=0)
> sending NMI to all CPUs:
> NMI backtrace for cpu 3
> CPU: 3 PID: 29664 Comm: trinity-child2 Not tainted 3.11.0-rc1+ #32
> task: ffff88023e743fc0 ti: ffff88022f6f2000 task.ti: ffff88022f6f2000
> RIP: 0010:[<ffffffff810bf7d1>]  [<ffffffff810bf7d1>] trace_hardirqs_off_caller+0x21/0xb0
> RSP: 0018:ffff880244e03c30  EFLAGS: 00000046
> RAX: ffff88023e743fc0 RBX: 0000000000000001 RCX: 000000000000003c
> RDX: 000000000000000f RSI: 0000000000000004 RDI: ffffffff81033cab
> RBP: ffff880244e03c38 R08: ffff880243288a80 R09: 0000000000000001
> R10: 0000000000000000 R11: 0000000000000001 R12: ffff880243288a80
> R13: ffff8802437eda40 R14: 0000000000080000 R15: 000000000000d010
> FS:  00007f50ae33b740(0000) GS:ffff880244e00000(0000) knlGS:0000000000000000
> CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> CR2: 000000000097f000 CR3: 0000000240fa0000 CR4: 00000000001407e0
> DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
> DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000600
> Stack:
>  ffffffff810bf86d ffff880244e03c98 ffffffff81033cab 0000000000000096
>  000000000000d008 0000000300000002 0000000000000004 0000000000000003
>  0000000000002710 ffffffff81c50d00 ffffffff81c50d00 ffff880244fcde00
> Call Trace:
>  <IRQ>
>  [<ffffffff810bf86d>] ? trace_hardirqs_off+0xd/0x10
>  [<ffffffff81033cab>] __x2apic_send_IPI_mask+0x1ab/0x1c0
>  [<ffffffff81033cdc>] x2apic_send_IPI_all+0x1c/0x20
>  [<ffffffff81030115>] arch_trigger_all_cpu_backtrace+0x65/0xa0
>  [<ffffffff811144b1>] rcu_check_callbacks+0x331/0x8e0
>  [<ffffffff8108bfa0>] ? hrtimer_run_queues+0x20/0x180
>  [<ffffffff8109e905>] ? sched_clock_cpu+0xb5/0x100
>  [<ffffffff81069557>] update_process_times+0x47/0x80
>  [<ffffffff810bd115>] tick_sched_handle.isra.16+0x25/0x60
>  [<ffffffff810bd231>] tick_sched_timer+0x41/0x60
>  [<ffffffff8108ace1>] __run_hrtimer+0x81/0x4e0
>  [<ffffffff810bd1f0>] ? tick_sched_do_timer+0x60/0x60
>  [<ffffffff8108b93f>] hrtimer_interrupt+0xff/0x240
>  [<ffffffff8102de84>] local_apic_timer_interrupt+0x34/0x60
>  [<ffffffff81718c5f>] smp_apic_timer_interrupt+0x3f/0x60
>  [<ffffffff817178ef>] apic_timer_interrupt+0x6f/0x80
>  [<ffffffff8170e8e0>] ? retint_restore_args+0xe/0xe
>  [<ffffffff8105f101>] ? __do_softirq+0xb1/0x440
>  [<ffffffff8105f64d>] irq_exit+0xcd/0xe0
>  [<ffffffff81718c65>] smp_apic_timer_interrupt+0x45/0x60
>  [<ffffffff817178ef>] apic_timer_interrupt+0x6f/0x80
>  <EOI>
>  [<ffffffff8170e8e0>] ? retint_restore_args+0xe/0xe
>  [<ffffffff8170b830>] ? wait_for_completion_killable+0x170/0x170
>  [<ffffffff8170c853>] ? preempt_schedule_irq+0x53/0x90
>  [<ffffffff8170e9f6>] retint_kernel+0x26/0x30
>  [<ffffffff8107a523>] ? queue_work_on+0x43/0x90
>  [<ffffffff8107c369>] schedule_on_each_cpu+0xc9/0x1a0
>  [<ffffffff81167770>] ? lru_add_drain+0x50/0x50
>  [<ffffffff811677c5>] lru_add_drain_all+0x15/0x20
>  [<ffffffff81186965>] SyS_mlockall+0xa5/0x1a0
>  [<ffffffff81716e94>] tracesys+0xdd/0xe2

This commit addresses this problem by inserting the required preemption
point.
Reported-by: NDave Jones <davej@redhat.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer code update from Thomas Gleixner:
 - armada SoC clocksource overhaul with a trivial merge conflict
 - Minor improvements to various SoC clocksource drivers

* 'timers/core' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: armada-370-xp: Add detailed clock requirements in devicetree binding
  clocksource: armada-370-xp: Get reference fixed-clock by name
  clocksource: armada-370-xp: Replace WARN_ON with BUG_ON
  clocksource: armada-370-xp: Fix device-tree binding
  clocksource: armada-370-xp: Introduce new compatibles
  clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
  clocksource: armada-370-xp: Simplify TIMER_CTRL register access
  clocksource: armada-370-xp: Use BIT()
  ARM: timer-sp: Set dynamic irq affinity
  ARM: nomadik: add dynamic irq flag to the timer
  clocksource: sh_cmt: 32-bit control register support
  clocksource: em_sti: Convert to devm_* managed helpers

Pull CIFS fixes from Steve French:
 "Two minor cifs fixes and a minor documentation cleanup for cifs.txt"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update cifs.txt and remove some outdated infos
  cifs: Avoid calling unlock_page() twice in cifs_readpage() when using fscache
  cifs: Do not take a reference to the page in cifs_readpage_worker()

Pull UBI fixes from Artem Bityutskiy:
 "Just a single fastmap fix plus a regression fix"

* tag 'upstream-3.12-rc1' of git://git.infradead.org/linux-ubi:
  UBI: Fix invalidate_fastmap()
  UBI: Fix PEB leak in wear_leveling_worker()

Pull ubifs fix from Artem Bityutskiy:
 "Just one patch which fixes the power-cut recovery testing mode.

  I'll start using a single UBI/UBIFS tree instead of 2 trees from now
  on.  So in the future you'll get 1 small pull request instead of 2
  tiny ones"

* tag 'upstream-3.12-rc1' of git://git.infradead.org/linux-ubifs:
  UBIFS: remove invalid warn msg with tst_recovery enabled

Pull MIPS fixes from Ralf Baechle:
 "These are four patches for three construction sites:

   - Fix register decoding for the combination of multi-core processors
     and multi-threading.

   - Two more fixes that are part of the ongoing DECstation resurrection
     work.  One of these touches a DECstation-only network driver.

   - Finally Markos' trivial build fix for the AP/SP support.

  (With this applied now all MIPS defconfigs are building again)"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: kernel: vpe: Make vpe_attrs an array of pointers.
  MIPS: Fix SMP core calculations when using MT support.
  MIPS: DECstation I/O ASIC DMA interrupt handling fix
  MIPS: DECstation HRT initialization rearrangement

Pull x86 platform updates from Matthew Garrett:
 "Nothing amazing here, almost entirely cleanups and minor bugfixes and
  one bit of hardware enablement in the amilo-rfkill driver"

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
  platform/x86: panasonic-laptop: reuse module_acpi_driver
  samsung-laptop: fix config build error
  platform: x86: remove unnecessary platform_set_drvdata()
  amilo-rfkill: Enable using amilo-rfkill with the FSC Amilo L1310.
  wmi: parse_wdg() should return kernel error codes
  hp_wmi: Fix unregister order in hp_wmi_rfkill_setup()
  platform: replace strict_strto*() with kstrto*()
  x86: irst: use module_acpi_driver to simplify the code
  x86: smartconnect: use module_acpi_driver to simplify the code
  platform samsung-q10: use ACPI instead of direct EC calls
  thinkpad_acpi: add the ability setting TPACPI_LED_NONE by quirk
  thinkpad_acpi: return -NODEV while operating uninitialized LEDs

Pull misc SCSI driver updates from James Bottomley:
 "This patch set is a set of driver updates (megaraid_sas, fnic, lpfc,
  ufs, hpsa) we also have a couple of bug fixes (sd out of bounds and
  ibmvfc error handling) and the first round of esas2r checker fixes and
  finally the much anticipated big endian additions for megaraid_sas"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
  [SCSI] fnic: fnic Driver Tuneables Exposed through CLI
  [SCSI] fnic: Kernel panic while running sh/nosh with max lun cfg
  [SCSI] fnic: Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset
  [SCSI] fnic: Remove QUEUE_FULL handling code
  [SCSI] fnic: On system with >1.1TB RAM, VIC fails multipath after boot up
  [SCSI] fnic: FC stat param seconds_since_last_reset not getting updated
  [SCSI] sd: Fix potential out-of-bounds access
  [SCSI] lpfc 8.3.42: Update lpfc version to driver version 8.3.42
  [SCSI] lpfc 8.3.42: Fixed issue of task management commands having a fixed timeout
  [SCSI] lpfc 8.3.42: Fixed inconsistent spin lock usage.
  [SCSI] lpfc 8.3.42: Fix driver's abort loop functionality to skip IOs already getting aborted
  [SCSI] lpfc 8.3.42: Fixed failure to allocate SCSI buffer on PPC64 platform for SLI4 devices
  [SCSI] lpfc 8.3.42: Fix WARN_ON when driver unloads
  [SCSI] lpfc 8.3.42: Avoided making pci bar ioremap call during dual-chute WQ/RQ pci bar selection
  [SCSI] lpfc 8.3.42: Fixed driver iocbq structure's iocb_flag field running out of space
  [SCSI] lpfc 8.3.42: Fix crash on driver load due to cpu affinity logic
  [SCSI] lpfc 8.3.42: Fixed logging format of setting driver sysfs attributes hard to interpret
  [SCSI] lpfc 8.3.42: Fixed back to back RSCNs discovery failure.
  [SCSI] lpfc 8.3.42: Fixed race condition between BSG I/O dispatch and timeout handling
  [SCSI] lpfc 8.3.42: Fixed function mode field defined too small for not recognizing dual-chute mode
  ...

Pull SLAB update from Pekka Enberg:
 "Nothing terribly exciting here apart from Christoph's kmalloc
  unification patches that brings sl[aou]b implementations closer to
  each other"

* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
  slab: Use correct GFP_DMA constant
  slub: remove verify_mem_not_deleted()
  mm/sl[aou]b: Move kmallocXXX functions to common code
  mm, slab_common: add 'unlikely' to size check of kmalloc_slab()
  mm/slub.c: beautify code for removing redundancy 'break' statement.
  slub: Remove unnecessary page NULL check
  slub: don't use cpu partial pages on UP
  mm/slub: beautify code for 80 column limitation and tab alignment
  mm/slub: remove 'per_cpu' which is useless variable

Pull input update from Dmitry Torokhov:
 "The only change is David Hermann's new EVIOCREVOKE evdev ioctl that
  allows safely passing file descriptors to input devices to session
  processes and later being able to stop delivery of events through
  these fds so that inactive sessions will no longer receive user input
  that does not belong to them"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: evdev - add EVIOCREVOKE ioctl

Sedat points out that I transposed some letters in "LRU" and wrote "RLU"
instead in one of the new comments explaining the flow.  Let's just fix
it.
Reported-by: NSedat Dilek <sedat.dilek@jpberlin.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Matt found that commit 27a7c642 ("partitions/efi: account for pmbr
size in lba") caused his GPT formatted eMMC device not to boot.  The
reason is that this commit enforced Linux to always check the lesser of
the whole disk or 2Tib for the pMBR size in LBA.  While most disk
partitioning tools out there create a pMBR with these characteristics,
Microsoft does not, as it always sets the entry to the maximum 32-bit
limitation - even though a drive may be smaller than that[1].

Loosen this check and only verify that the size is either the whole disk
or 0xFFFFFFFF.  No tool in its right mind would set it to any value
other than these.

[1] http://thestarman.pcministry.com/asm/mbr/GPT.htm#GPTPTReported-and-tested-by: NMatt Porter <matt.porter@linaro.org>
Signed-off-by: NDavidlohr Bueso <davidlohr@hp.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull writeback fix from Wu Fengguang:
 "A trivial writeback fix"

* tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
  writeback: Do not sort b_io list only because of block device inode

The LRU list changes interacted badly with our nr_dentry_unused
accounting, and even worse with the new DCACHE_LRU_LIST bit logic.

This introduces helper functions to make sure everything follows the
proper dcache d_lru list rules: the dentry cache is complicated by the
fact that some of the hotpaths don't even want to look at the LRU list
at all, and the fact that we use the same list entry in the dentry for
both the LRU list and for our temporary shrinking lists when removing
things from the LRU.

The helper functions temporarily have some extra sanity checking for the
flag bits that have to match the current LRU state of the dentry.  We'll
remove that before the final 3.12 release, but considering how easy it
is to get wrong, this first cleanup version has some very particular
sanity checking.
Acked-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Acked-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NBjörn JACKE <bj@sernet.de>
Signed-off-by: NSteve French <smfrench@gmail.com>

When reading a single page with cifs_readpage(), we make a call to
fscache_read_or_alloc_page() which once done, asynchronously calls
the completion function cifs_readpage_from_fscache_complete(). This
completion function unlocks the page once it has been populated from
cache. The module then attempts to unlock the page a second time in
cifs_readpage() which leads to warning messages.

In case of a successful call to fscache_read_or_alloc_page() we should skip
the second unlock_page() since this will be called by the
cifs_readpage_from_fscache_complete() once the page has been populated by
fscache.

With the modifications to cifs_readpage_worker(), we will need to re-grab the
page lock in cifs_write_begin().

The problem was first noticed when testing new fscache patches for cifs.
https://bugzilla.redhat.com/show_bug.cgi?id=1005737Signed-off-by: NSachin Prabhu <sprabhu@redhat.com>
Reviewed-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NSteve French <smfrench@gmail.com>

We do not need to take a reference to the pagecache in
cifs_readpage_worker() since the calling function will have already
taken one before passing the pointer to the page as an argument to the
function.
Signed-off-by: NSachin Prabhu <sprabhu@redhat.com>
Reviewed-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NSteve French <smfrench@gmail.com>

Pull hwmon fixes from Guenter Roeck:
 "Some more low risk cleanup patches:

   - Remove unnecessary pci_set_drvdata in k10temp driver from Jingoo Han
   - Fix return values in several drivers from Sachin Kamat
   - Remove redundant break in amc6821 driver from Sachin Kamat"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (k10temp) remove unnecessary pci_set_drvdata()
  hwmon: (tmp421) Fix return value
  hwmon: (amc6821) Remove redundant break
  hwmon: (amc6821) Fix return value
  hwmon: (ibmaem) Fix return value
  hwmon: (emc2103) Fix return value

Pull Xtensa updates from Chris Zankel.

* tag 'xtensa-next-20130912' of git://github.com/czankel/xtensa-linux:
  xtensa: Fix broken allmodconfig build
  xtensa: remove CCOUNT_PER_JIFFY
  xtensa: fix !CONFIG_XTENSA_CALIBRATE_CCOUNT build failure
  xtensa: don't use echo -e needlessly
  xtensa: new fast_alloca handler
  xtensa: keep a3 and excsave1 on entry to exception handlers
  xtensa: enable kernel preemption
  xtensa: check thread flags atomically on return from user exception

Pull aio changes from Ben LaHaise:
 "First off, sorry for this pull request being late in the merge window.
  Al had raised a couple of concerns about 2 items in the series below.
  I addressed the first issue (the race introduced by Gu's use of
  mm_populate()), but he has not provided any further details on how he
  wants to rework the anon_inode.c changes (which were sent out months
  ago but have yet to be commented on).

  The bulk of the changes have been sitting in the -next tree for a few
  months, with all the issues raised being addressed"

* git://git.kvack.org/~bcrl/aio-next: (22 commits)
  aio: rcu_read_lock protection for new rcu_dereference calls
  aio: fix race in ring buffer page lookup introduced by page migration support
  aio: fix rcu sparse warnings introduced by ioctx table lookup patch
  aio: remove unnecessary debugging from aio_free_ring()
  aio: table lookup: verify ctx pointer
  staging/lustre: kiocb->ki_left is removed
  aio: fix error handling and rcu usage in "convert the ioctx list to table lookup v3"
  aio: be defensive to ensure request batching is non-zero instead of BUG_ON()
  aio: convert the ioctx list to table lookup v3
  aio: double aio_max_nr in calculations
  aio: Kill ki_dtor
  aio: Kill ki_users
  aio: Kill unneeded kiocb members
  aio: Kill aio_rw_vect_retry()
  aio: Don't use ctx->tail unnecessarily
  aio: io_cancel() no longer returns the io_event
  aio: percpu ioctx refcount
  aio: percpu reqs_available
  aio: reqs_active -> reqs_available
  aio: fix build when migration is disabled
  ...

Pull generic hardirq option removal from Martin Schwidefsky:
 "All architectures now use generic hardirqs, s390 has been last to
  switch.

  With that the code under !CONFIG_GENERIC_HARDIRQS and the related
  HAVE_GENERIC_HARDIRQS and GENERIC_HARDIRQS config options can be
  removed.  Yay!"

* 'genirq' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  Remove GENERIC_HARDIRQ config option

Pull kconfig fix from Michal Marek:
 "This is a fix for a regression caused by my previous pull request.

  A sed command in scripts/config that used colons as separator was
  accidentally changed to use slashes, which fails when you use slashes
  in a value.  Changing it back to colons is of course not a proper fix,
  but at least it will be broken in the same way it had been for four
  years.  A proper fix is pending"

* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  scripts/config: fix variable substitution command

Merge tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux

Pull blackfin updates from Steven Miao.

* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
  blackfin: Ignore generated uImages
  blackfin: Add STMMAC platform data to enable dwmac1000 driver on BF60x.
  bf609: adv7343: add S-Video and Component output support
  bf609: add adv7343 video encoder support
  clock: add stmmac clock for ethernet driver
  blackfin: scb: Add SCB1 to SCB9 config options and data.
  blackfin: scb: Add system crossbar init code.

Pull crypto fixes from Herbert Xu:
 "This fixes a 7+ year race condition in the crypto API that causes
  sporadic crashes when multiple threads load the same algorithm.

  It also fixes the crct10dif algorithm again to prevent boot failures
  on systems where the initramfs tool ignores module softdeps"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: crct10dif - Add fallback for broken initrds
  crypto: api - Fix race condition in larval lookup

Commit 567b21e9
"mips: convert vpe_class to use dev_groups"

broke the build on MIPS since vpe_attrs should be an array
of 'struct device_attribute' pointers.

Fixes the following build problem:
arch/mips/kernel/vpe.c:1372:2: error: missing braces around initializer
[-Werror=missing-braces]
arch/mips/kernel/vpe.c:1372:2: error: (near initialization for 'vpe_attrs[0]')
[-Werror=missing-braces]

Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5819/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Commit 229455bc02b87f7128f190c4491b4ceffff38648 accidentally changed the
separator between sed `s' command and its parameters from ':' to '/'.

Revert this change.
Reported-and-tested-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NClement Chauplannaz <chauplac@gmail.com>
Signed-off-by: NMichal Marek <mmarek@suse.cz>

The TCBIND register is only available if the core has MT support. It
should not be read otherwise. Secondly, the number of TCs (siblings)
are calculated differently depending on if the kernel is configured
as SMVP or SMTC.
Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: NSteven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5822/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.

Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle).  Otherwise the handler is
reentered over and over again.

The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared.  Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'.  Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Not all I/O ASIC versions have the free-running counter implemented, an
early revision used in the 5000/1xx models aka 3MIN and 4MIN did not have
it.  Therefore we cannot unconditionally use it as a clock source.
Fortunately if not implemented its register slot has a fixed value so it
is enough if we check for the value at the end of the calibration period
being the same as at the beginning.

This also means we need to look for another high-precision clock source on
the systems affected.  The 5000/1xx can have an R4000SC processor
installed where the CP0 Count register can be used as a clock source.
Unfortunately all the R4k DECstations suffer from the missed timer
interrupt on CP0 Count reads erratum, so we cannot use the CP0 timer as a
clock source and a clock event both at a time.  However we never need an
R4k clock event device because all DECstations have a DS1287A RTC chip
whose periodic interrupt can be used as a clock source.

This gives us the following four configuration possibilities for I/O ASIC
DECstations:

1. No I/O ASIC counter and no CP0 timer, e.g. R3k 5000/1xx (3MIN).

2. No I/O ASIC counter but the CP0 timer, i.e. R4k 5000/150 (4MIN).

3. The I/O ASIC counter but no CP0 timer, e.g. R3k 5000/240 (3MAX+).

4. The I/O ASIC counter and the CP0 timer, e.g. R4k 5000/260 (4MAX+).

For #1 and #2 this change stops the I/O ASIC free-running counter from
being installed as a clock source of a 0Hz frequency.  For #2 it also
arranges for the CP0 timer to be used as a clock source rather than a
clock event device, because having an accurate wall clock is more
important than a high-precision interval timer.  For #3 there is no
change.  For #4 the change makes the I/O ASIC free-running counter
installed as a clock source so that the CP0 timer can be used as a clock
event device.

Unfortunately the use of the CP0 timer as a clock event device relies on a
succesful completion of c0_compare_interrupt.  That never happens, because
while waiting for a CP0 Compare interrupt to happen the function spins in
a loop reading the CP0 Count register.  This makes the CP0 Count erratum
trigger reliably causing the interrupt waited for to be lost in all cases.
As a result #4 resorts to using the CP0 timer as a clock source as well,
just as #2.  However we want to keep this separate arrangement in case
(hope) c0_compare_interrupt is eventually rewritten such that it avoids
the erratum.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5825/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We have the build infrastructure to generate uImages so we should ignore
the resulting generated files.
Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NMike Frysinger <vapier@gentoo.org>