* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
  and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.

* Add set_pio_mode_abuse() for checking if host driver has a non-standard
  ->tuneproc() implementation and use it in do_special().

* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
  the maximum PIO mode supported by the host), also add ide_set_max_pio()
  wrapper for ide_set_pio() to use for auto-tuning.  Convert users of
  ->tuneproc to use ide_set{_max}_pio() where possible.  This leaves only
  do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
  a direct users of ->tuneproc.

* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
  reporting PIO mode selected from ->tuneproc implementations.

* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.

* Remove stale comment from ide_config_drive_speed().

v2:
* Fix "ata_" prefix (Noticed by Jeff).

v3:
* Minor cleanups/fixups per Sergei's suggestions.

v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
  (Noticed by Andrew Morton).

* Improve some ->set_pio_mode comments.
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move ide_rate_filter() calls from host drivers to IDE core.

* Make ide_rate_filter() static.

* Make 'speed' argument of ->speedproc const.

v2:
* Fix it8213_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add an extra argument to ide_max_dma_mode() for passing requested transfer
  mode.  Use it as an upper limit when finding the best DMA for device/host.

* Rename ide_max_dma_mode() to ide_find_dma_mode() and at the same time add
  ide_max_dma_mode() wrapper which passes XFER_UDMA_6 as a requested mode to
  ide_find_dma_mode().  Also add inline ide_find_dma_mode() version for
  CONFIG_BLK_DEV_IDEDMA=n case.

* Pass requested transfer mode from ide_find_dma_mode() to ide_get_mode_mask()
  to avoid false warning from eighty_ninty_three().

* Use ide_find_dma_mode() to limit the user requested transfer mode in
  ide_rate_filter().  Also limit the requested mode by host max PIO mode.


Above changes make ide_rate_filter() to:

* Clip desired transfer mode down if it is invalid (values 0x0F, 0x13-0x19
  and 0x25-0x39, values > 0x46 were already clipped down, same for values
  0x25-0x39 but iff UDMA was not supported by the host).

* Clip desired transfer mode down if it is currently unsupported by IDE core
  (PIO6 and MWDMA3-4, the latter were already clipped down but iff UDMA was
  not supported by the host).

* Clip desired transfer mode down according to the host capabilities
  (UDMA modes were already clipped down but MWDMA/SWDMA/PIO weren't,
  also ->atapi_dma flag was not respected).

* Clip desired transfer mode down according to the device capabilities
  (except PIO modes for now which require mode work) - shouldn't be a
  problem since ide_set_xfer_rate() is called _after_ device has accepted
  given transfer mode.

and also result in a number of host driver specific bugfixes:

* icside
  - clip unsupported PIO5 mode down
  - fix unsupported/invalid modes being set in drive->current_speed

* ide-cris
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
  - fix BUG() on unsupported/invalid modes

* au1xxx-ide
  - clip unsupported PIO5, SWDMA0-2 and MWDMA0-2
    (if BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=n) modes down

* aec62xx
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
  - fix 0x00 being programmed as PIO timing for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* alim15x3
  - clip DMA modes down for ATAPI devices (chipset revision == 0x20 only)
  - fix theoretical OOPS for 0x0F mode
  - fix unsupported/invalid modes being set on the device

* amd74xx
  - clip unsupported SWDMA0-2 (on COBRA_7401 revs <= 7) modes down
  - fix random PIO timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* atiixp
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix cached MWDMA mode being cleared for unsupported/invalid modes
  - fix PIO{0,2} timings being programmed for unsupported/invalid modes
  - fix theoretical OOPS for PIO5-6 and 0x0F modes
  - fix unsupported/invalid modes being set on the device

* cmd64x
  - clip unsupported SWDMA0-2 modes down

* cs5530
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix BUG() on unsupported/invalid modes
    (which happened if the device accepted the setting)

* cs5535
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix theoretical OOPS for PIO5-6 and 0x0F modes

* hpt34x
  - clip DMA modes down for ATAPI devices
  - fix invalid timings being programmed for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* hpt366
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix PIO0 timings being programmed for unsupported/invalid modes
  - fix DMA timings being cleared for MWDMA3-4 and 0x25-0x39 modes
  - fix unsupported/invalid modes being set on the device

* it8213
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* it821x
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices
    (chipset in smart mode and revision 0x10 in pass-through mode)

* jmicron
  - clip unsupported SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device

* pdc202xx_new
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device

* pdc202xx_old
  - clip unsupported PIO5 mode down
  - fix incorrect timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* piix
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* sc1200
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix unsupported/invalid modes being set on the device
  - fix BUG() on unsupported/invalid modes
    (which happened if the device accepted the setting)

* scc_pata
  - clip unsupported PIO5, SWDMA0-2 and MWDMA0-2 modes down

* serverworks
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix DMA/UDMA timings/settings being cleared for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* siimage
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - clip DMA modes down for ATAPI devices (SATA chipsets)

* sis5513
  - clip unsupported PIO5 mode down
  - fix BUG() on unsupported/invalid modes

* sl82c105
  - clip unsupported SWDMA0-2 modes down

* slc90e66
  - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down

* tc86c001
  - clip unsupported PIO5 and SWDMA0-2 modes down
  - fix PIO0 timings being programmed for PIO5/0x0F/SWDMA0-2/0x13-0x19 modes
  - fix invalid 0x00 DMA timing being programmed for MWDMA3-4/0x25-0x39 modes
  - fix unsupported/invalid modes being set on the device

* triflex
  - clip unsupported PIO5 mode down

* via82cxxx
  - fix random PIO timings being set for unsupported/invalid modes
  - fix unsupported/invalid modes being set on the device

* pmac
  - clip unsupported PIO5 and SWDMA0-2 modes down

* cmd640/ht6560b
  - clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
  - fix PIO5 being clipped to PIO4 (if CONFIG_BLK_DEV_IDEDMA=n)

* opti621
  - clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
  - clip unsupported PIO4 to PIO3 (if CONFIG_BLK_DEV_IDEDMA=n)


While at it:

* Use ide_rate_filter() in cs5520.c::cs5520_tune_chipset().

* Remove no longer needed checks from hpt366.c::hpt3{6,7}x_tune_chipset().
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ATA_PIO[0-6] defines to <linux/ata.h>.

* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.

* Add PIO masks to host drivers.

<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
  and convert all users accordingly.

* Remove no longer needed ide_pio_data_t.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags
  and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS.

* Add IDE_HFLAG_SINGLE flag for single channel devices.

* Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE
  and remove no longer needed ide_pci_device_t.channels field.

v2:
* Fix issues noticed by Sergei:
  - correct code alignment in scc_pata.c
  - s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* create_proc_ide_interfaces() tries to add /proc entries for every probed
  and initialized IDE port, replace it by ide_proc_register_port() which does
  it only for the given port (also rename destroy_proc_ide_interface() to
  ide_proc_unregister_port() for consistency)
  
* convert {create,destroy}_proc_ide_interface[s]() users to use new functions

* pmac driver depended on proc_ide_create() to add /proc port entries, fix it
  
* au1xxx-ide, swarm and cs5520 drivers depended indirectly on ide-generic
  driver (CONFIG_IDE_GENERIC=y) to add port /proc entries, fix them

* there is now no need to add /proc entries for IDE ports in proc_ide_create()
  so don't do it

* proc_ide_create() needs now to be called before drivers are probed - fix it,
  while at it make proc_ide_create() create /proc "ide" directory
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
  -1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
   0 when DMA needs to be enabled  (== need to call ->ide_dma_on)
   1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

also change __devinit tag for sgiioc4.c:ioc4_ide_init() to __init
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

From: Amit Gud <amitg@calsoftinc.com>

Patch follows from the suggestions by AC and Felipe W Damasio for fixing the
return codes from IDE drivers.

[ bart: fix coding style while at it ]
Signed-off-by: NAmit Gud <gud@eth.net>
Signed-off-by: NDomen Puncer <domen@coderock.org>
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!