- 10 5月, 2015 23 次提交
-
-
由 Edward Cree 提交于
* Accept EPERM in some simple cases, the following cases are handled: 1) efx_mcdi_read_assertion() Unprivileged PCI functions aren't allowed to GET_ASSERTS. We return success as it's up to the primary PF to deal with asserts. 2) efx_mcdi_mon_probe() in efx_ef10_probe() Unprivileged PCI functions aren't allowed to read sensor info, and worrying about sensor data is the primary PF's job. 3) phy_op->reconfigure() in efx_init_port() and efx_reset_up() Unprivileged functions aren't allowed to MC_CMD_SET_LINK, they just have to accept the settings (including flow-control, which is what efx_init_port() is worried about) they've been given. 4) Fallback to GET_WORKAROUNDS in efx_ef10_probe() Unprivileged PCI functions aren't allowed to set workarounds. So if efx_mcdi_set_workaround() fails EPERM, use efx_mcdi_get_workarounds() to find out if workaround_35388 is enabled. 5) If DRV_ATTACH gets EPERM, try without specifying fw-variant Unprivileged PCI functions have to use a FIRMWARE_ID of 0xffffffff (MC_CMD_FW_DONT_CARE). 6) Don't try to exit_assertion unless one had fired Previously we called efx_mcdi_exit_assertion even if efx_mcdi_read_assertion had received MC_CMD_GET_ASSERTS_FLAGS_NO_FAILS. This is unnecessary, and the resulting MC_CMD_REBOOT, even if the AFTER_ASSERTION flag made it a no-op, would fail EPERM for unprivileged PCI functions. So make efx_mcdi_read_assertion return whether an assert happened, and only call efx_mcdi_exit_assertion if it has. Signed-off-by: NShradha Shah <sshah@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shradha Shah 提交于
To be able to use MC_CMD_VADAPTOR_SET_MAC, vadaptors must be manually allocated and freed as automatic vadaptors will disappear when their reference_count reaches zero, which must happen before the MAC address is changed. Vadaptors are allocated and freed in the vswitching_probe/remove functions for PFs and VFs, and this means that vadaptors are restored correctly following an MC reboot or other reset when required. Signed-off-by: NShradha Shah <sshah@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shradha Shah 提交于
The parent PF creates vports for all its child VFs and adds MAC addresses to these. When the VF driver loads, it can make an MCDI call to get the MAC address that the parent PF assigned it. The parent PF also assigns a mac address to its own vport because implicit creation of a vAdaptor will only work on evb ports with MAC addresses assigned. The vport MAC address needs to be stored in the PF's nic_data struct as it can later be changed on the vadaptor (and its net_dev struct). When removing a vport the original MAC address must be deleted. A new flag is needed in the VF data structure to identify whether a vport has been assigned to the VF. This is to determine whether it needs to be un-assigned before freeing the vport. Also, attempting to un-assign a vport which is not assigned will result in an EALREADY error. Signed-off-by: NShradha Shah <sshah@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shradha Shah 提交于
Added efx_nic_type structure for VF. Mapped a different BAR for VF as it uses BAR 0 for memory. Added functions sriov_init and sriov_fini. Signed-off-by: NShradha Shah <sshah@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Daniel Pieczko 提交于
Use MC_CMD_GET_FUNCTION_INFO to record the PF number in nic_data. This will be needed when assigned vports to VFs. Signed-off-by: NShradha Shah <sshah@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Daniel Pieczko 提交于
Adds functions to allocate and free vswitches and vports; vadaptors are automatically allocated and freed when TX/RX queues are initialised and finalised. This vswitching structure is only created if the firmware supports it, so a check that full-featured firmware is running is performed first. If the MC resets, the vswitching infrastructure will need to be recreated, so mark the "must_probe_vswitching" flag when an MC reboot is detected. Don't try to create a vswitch if vf-count=0 This allocation of vswitches and vports does not currently support configuring VLAN tags, but that can be added in a future change. Signed-off-by: NShradha Shah <sshah@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Daniel Pieczko 提交于
The default port ID of EVB_PORT_ID_ASSIGNED is a "magic" number for the MCFW to select the physical port of the PF. If other vswitches and vports are created on top of the default firmware configuration, the ID of the newly created vport is then required when passed to MCDI commands. Currently, this doesn't happen so the vport_id is never changed, but a subsequent patch will change this behaviour so that other vswitches and vports are created. The vport_id recorded in nic_data is only relevant for PFs. VFs will have their vports created by their parent PF, and in that case the parent PF will record the vport ID of each VF. For a VF, nic_data->vport_id is expected to remain at the default value. Signed-off-by: NShradha Shah <sshah@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Daniel Pieczko 提交于
The (future) code to add/remove vswitches and vports will be dependent on the firmware variant. To simplify the checking of the firmware variant, record values for rx_dpcpu_fw_id and tx_dpcpu_fw_id in EF10 nic_data. There was only one place where this was previously used: efx_mcdi_print_fwver() in ethtool.c. The MC_CMD_GET_CAPABILITIES can be replaced and the values from nic_data used instead. Note that the printing of "?" if the MC command fails or if the outlength is incorrect no longer apply, because errors are returned in efx_ef10_init_datapath_caps() in both of these cases. Signed-off-by: NShradha Shah <sshah@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shradha Shah 提交于
The TX_DOMAIN field is currently reserved but its safer to set it to 0 for future compatibility. Signed-off-by: NShradha Shah <sshah@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shradha Shah 提交于
This patch adds support for the use of sriov_configure on EF10 to enable Virtual Functions while the driver is loaded. Signed-off-by: NShradha Shah <sshah@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Daniel Pieczko 提交于
The efx_vf struct contains Siena-specific fields for VFs, so rename to siena_vf. Also move it into the siena_nic_data struct, as EF10 will track its VFs in its own ef10_nic_data, storing much less information about them since VFDI is no longer used. Signed-off-by: NShradha Shah <sshah@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shradha Shah 提交于
sfc: Own header for nic-specific sriov functions, single instance of netdev_ops and sriov removed from Falcon code By putting all the efx_{siena,ef10}_sriov_* declarations in {siena,ef10}_sriov.h, ensure they cannot be called from nic-generic code. Also fixes up an instance of this, where mcdi.c was calling efx_siena_sriov_flr. The single instance of netdev_ops should call general high level functions that can then call something adapter specific in efx_nic_type. We should only do adapter specialisation via efx_nic_type. Removal of sriov functionality from the Falcon code means that tests are needed for the presence of some callbacks. Signed-off-by: NShradha Shah <sshah@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Andrew Lunn says: ==================== More Marvell DSA refactring and fixup This patch setup continues the refactoring and cleanup of the Marvell DSA drivers. Patch #1 Centralizes the duplicated parts of port setup and global setup into the shared mv88e6xxx. Patch #2 Centralizes looping over the ports setting them up Patch #3 Uses mnemonics for the remaining register access in the drivers. Patch #4 The 6172 is actually a member of the 6352 family. This moves the probe code into the correct driver. Patch #5 Adds more members of the 6171 family to the 6171 driver. The new devices are untested. Patch #6 The 6185 is a member of the 6131 family. Add it to the probe code of the 6131 driver. Patch #7 and Patch #8 Simply the mutex's in mv88e6xxx.c. The SMI bus is the bottleneck, not the granularity of the mutex's so simply the code down to a single mutex. Patch #8 Fixes a false positive lockdep splat, due to nested uses of MDIO busses. Patch #9 Fixes another false positive lockdep splat with the transmit queue because of stacked Ethernet devices. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
DSA stacks an Ethernet device on top of an Ethernet device. This can cause false positive lockdep splats for the transmit queue: Acked-by: NFlorian Fainelli <f.fainelli@gmail.com> ============================================= [ INFO: possible recursive locking detected ] 4.0.0-rc7-01838-g70621a215fc7 #386 Not tainted --------------------------------------------- kworker/0:0/4 is trying to acquire lock: (_xmit_ETHER#2){+.-...}, at: [<c040e95c>] sch_direct_xmit+0xa8/0x1fc but task is already holding lock: (_xmit_ETHER#2){+.-...}, at: [<c03f4208>] __dev_queue_xmit+0x4d4/0x56c other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(_xmit_ETHER#2); lock(_xmit_ETHER#2); To avoid this, walk the tq queues of the dsa slaves and set a lockdep class. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
DSA can have nested MDIO busses, where the Ethernet MDIO bus is used to access an MDIO bus within the switch which has the PHYs connected to it. This nesting causes lockdep to give false positives. Use mutex_lock_nested() to avoid this. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
The SMI bus is the bottleneck in all switch operations, not the granularity of locks. Replace the stats mutex by the SMI mutex to make the locking concept simpler. The REG_READ/REG_WRITE macros cannot be used while holding the SMI mutex, since they try to acquire it. Replace with calls to the appropriate function which does not try to get the mutex. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
The SMI bus is the bottleneck in all switch operations, not the granularity of locks. Replace the PHY mutex by the SMI mutex to make the locking concept simpler. The REG_READ/REG_WRITE macros cannot be used while holding the SMI mutex, since they try to acquire it. Replace with calls to the appropriate function which does not try to get the mutex. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
The mv88e6185 is part of the family that the mv88e6131 driver supports. Add it to the probe function, and set the number of ports. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
The 6171 is one member of the family 6171/6175/6350/6351. Add the other family members to the driver. Not tested on these new devices. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
The mv88e6172 is part of the mv88e6352 family of devices. Move support for it out of the mv88e6171 driver into the mv88e6352, which results in some simplifications to the code. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
Use defines for registers, shifts and bits in the remaining register accesses in the individual drivers, in order to aid readability. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
Now that setting up a port is identical for all switches, centralisers the code looping over all the ports to set them up. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
The port setup code in the individual drivers is identical for 6123, 6171, and 6352, and very similar in 6131. Move it all into mv88e6xxx, using the chip families to differentiate on features. Similarly, the global setup is also very similar. Move the majority into mv8e6xxx. The chips themselves fall into families. Add helpers which uses the device IDs to determine if a device is a member of a family or not. Add some additional device IDs to the existing list, to make these helper functions more complete. However these IDs are not yet added to the probe functions. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 06 5月, 2015 17 次提交
-
-
由 Thomas Graf 提交于
VXLAN must provide the skb mark and specifiy IPPROTO_UDP when doing the FIB lookup for the remote ip. Otherwise an invalid route might be returned. Signed-off-by: NThomas Graf <tgraf@suug.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Simek 提交于
This patch remove kernel-doc warnings. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Srikanth Thokala 提交于
Synchronize names with other drivers. Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Srikanth Thokala 提交于
Use of_property_* calls Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Srikanth Thokala 提交于
use devm_* calls Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Srikanth Thokala 提交于
Synchronize names with other drivers Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Simek 提交于
There is rule for network drivers with comments blocks which is newly checked by checkpatch.pl script. Let's fix it. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Srikanth Thokala 提交于
Removed checkpatch.pl errors and warnings. Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Srikanth Thokala 提交于
This patch adds proper checks to handle the PHY-less case. Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Srikanth Thokala 提交于
In the current implementation, jumbo frames are supported only for the frame sizes > 16K. This patch corrects this logic to handle jumbo frames for lesser frame sizes (< 16K) ensuring jumbo frame MTU is within the limit of max frame size configured in the h/w design. Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peter Crosthwaite 提交于
The packet completion interrupts for TX and RX should be serviced before the packets are consumed. This ensures against the degenerate case when a new completion interrupt is raised after the handler has exited but before the interrupts are cleared. In this case its possible for the ISR to clear an unhandled interrupt (leading to potential deadlock). Signed-off-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com> Tested-by: NJason Wu <huanyu@xilinx.com> Acked-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peter Crosthwaite 提交于
The AXI-DMA rx-delay interrupt can sometimes be triggered when there are 0 outstanding packets received. This is due to the fact that the receive function will greedily consume as many packets as possible on interrupt. So if two packets (with a very particular timing) arrive in succession they will each cause the rx-delay interrupt, but the first interrupt will consume both packets. This means the second interrupt is a 0 packet receive. This is mostly OK, except that the tail pointer register is updated unconditionally on receive. Currently the tail pointer is always set to the current bd-ring descriptor under the assumption that the hardware has moved onto the next descriptor. What this means for length 0 recv is the current descriptor that the hardware is potentially yet to use will be marked as the tail. This causes the hardware to think its run out of descriptors deadlocking the whole rx path. Fixed by updating the tail pointer to the most recent successfully consumed descriptor. Reported-by: NWendy Liang <wendy.liang@xilinx.com> Signed-off-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com> Tested-by: NJason Wu <huanyu@xilinx.com> Acked-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Srikanth Thokala 提交于
This patch adds support for the RGMII. The h/w configuration parameter C_PHY_TYPE, which represents the interface configured in the design, is used to differentiate various interfaces supported by AXI Ethernet. Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Hariprasad Shenai says: ==================== Trivial fixes and changes for SGE This patch series adds the following. Discard packet if length is greater than MTU, move sge monitor code to a new routine, add device node to ULD info, add congestion notification from SGE for ingress queue and freelists and for T5, setting up the Congestion Manager values of the new RX Ethernet Queue is done by firmware now. This patch series has been created against net-next tree and includes patches on cxgb4 driver. We have included all the maintainers of respective drivers. Kindly review the change and let us know in case of any review comments. Thanks V2: Align parenthesis for PATCH 2/6 and PATCH 5/6 ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hariprasad Shenai 提交于
pktgen sends raw udp packets and bypasses most of the linux networking stack. User can specify different packet sizes. Hence we need to discard the packet if the length is greater than mtu Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hariprasad Shenai 提交于
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hariprasad Shenai 提交于
Adds device node to ULD info. Use the node info to alloc_ring() for ctrl TX queues Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-