Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Support for the SBC610 VPX Single Board Computer from GE (PowerPC MPC8641D).

This patch adds basic support for the on-board flash.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch enables the NVRAM found on the GE Fanuc SBC610
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Updated mpc85xx_{smp_}defconfig to enable:
* XES_MPC85xx board
* PCI MSI
* RapidIO
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Now that all EEPROM drivers live in the same place, let's harmonize
their symbol names.

Also fix eeprom's dependencies, it definitely needs sysfs, and is no
longer experimental after many years in the kernel tree.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>

Support for the FPGA based watchdog timer on GE Fanuc's SBC610.

This patch enables one of the watchdog timers found on the SBC610. There are
two identical watchdog timers at different offsets in the above mentioned
boards, however the current driver is only capable of supporting one of them.

The watchdog timers are also capable of generating interrupts at a
user-configurable threshold, though support for this operation is currently
not supported by the driver.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Adding use of newly added Epson RTX-8581 real-time clock driver to GE
Fanuc SBC610's dts file and adding driver to default config.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The Marvell PHY driver is currently being used for the 88E1111 on the
SBC610. This driver is causing the link to run in 10/Half mode, the generic
PHY driver is correctly configuring the PHY as 1000/Full.

Edit default config to use generic PHY driver.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

unset CONFIG_PCI_LEGACY in the defconfigs as none of them enable
ISDN drivers which seem to be the only place we are using pci_find_device
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Because CHRP and PMAC are by default enabled, several non-CHRP and non-PMAC
PowerPC defconfigs will have these Kconfig options set erroneously.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).

This is the default config file for GE Fanuc's SBC610, a 6U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Since we are updated defconfigs I went ahead and moved the
asp8347_defconfig under 83xx/ and the mpc8536_ds_defconfig under
85xx/ as that is where they should have been to start with.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This adds a sample defconfig for the Wind River SBC8641D
board, with SMP, PCI and NFS root enabled.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Board specific defconfigs are useful, however with the ability to do
multi-board defconfigs they aren't needed in the top level configs directory

Move the 83xx/85xx board specific defconfigs to individual directories under
arch/powerpc/configs.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This updates all the defconfigs in arch/powerpc/configs except iseries
and ps3, which were updated by the preceding commits.

This mostly takes the defaults, except that I turned on tickless idle
and high-resolution timers for everything, and turned off instrumentation
support and "Fair group CPU scheduler" for the smaller/embedded platforms.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Now the rtc class ds1374 driver has been added, remove the old rtc
driver hookup code, add rtc node to device trees, and turn on the
new driver in the defconfigs.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

When checking out the new NO_HZ support in powerpc, I noticed we never
slept for more than 2 seconds.  It turns out SLAB has a 2 second per cpu
timer that causes this.

After switching to SLUB I see some nice 4 second sleeps which is the
limit on this POWER6 box (the decrementer ticks at 512MHz):

slept 4.19 sec
slept 4.19 sec
slept 4.19 sec
slept 4.19 sec
slept 3.96 sec
slept 3.80 sec
slept 2.99 sec

Since SLUB is now the default and some powerpc defconfigs already enable
it, lets enable SLUB across the board for consistency.  While doing this
I also noticed that the maple defconfig has SLAB debugging enabled which
is sure to make your box nice and slow.  Fix that too.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Added the PCIe device node to the 8568 dts and the needed quirk entries.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Renamed the MPC8568 MDS platform code to follow other 85xx boards.  There
isn't anything specific about the 8568 MDS code that wouldn't apply to another
85xx MDS system at this point.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add defconfig for the MPC8568 MDS reference board
Signed-off-by: NAndrew Fleming <afleming@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The MPC834x SYS board has always been called the MPC834x MDS since its public
release.  Removed all references to SYS and replaced with MDS.  Additionally
renamed the .dts to match the defconfig (mpc834x_mds*).
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Updated MATH_EMULATION depends to be on PPC_MPC832x instead of PPC_83xx.  Only
the the MPC832x has no floating point unit in the core.  Updated the other
83xx defconfigs that got math emulation turned on incorrectly.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Mostly took the defaults, except tried to get the netfilter options
more or less as they were before.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes MPC834x MDS (formerly SYS) and ITX platform code to get IRQ data (including PCI) from the device tree, and to use the new IPIC code.

renamed defconfig (sys -> mds), left one redundant NULL assignment in mpc83xx_pcibios_fixup to keep the compiler happy.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add the first MPC83xx board that uses a flat device tree to arch/powerpc.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

MPC834x uses the gianfar network driver which now uses the new phylib.  We
need to update the platform code to create a gianfar platform MDIO bus and
pass the right intializations to the gianfar driver to make things work
again.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!