When selecting the native mode for a display we weren't taking into account
whether or not it was actually supported on that particular output.

This patch modifies our native mode selection to run all modes through
mode_valid() first.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

It was once assumed that all G8x had dual-link TMDS everywhere, this isn't
actually the case - especially considering passive DP->DVI converters and
some HDMI connectors only support single-link.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This resulted in accidently switching off the eDP panel on certain laptops
since the default state in the GPIO table was off.

Fixes rh#582621
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We totally fail at detecting un-POSTed chipsets prior to G80.  This commit
changes the pre-G80 POST detection to read the programmed horizontal total
from CRTC 0, and assume the card isn't POSTed if it's 0.

NVIDIA use some other heuristics more similar to what we do on G80, but I
wasted quite a long time trying to figure out the exact specifics of what
they do so we can try this for a bit instead.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This will be useful for computing GPU-CPU latency, including
GL_ARB_timer_query extension.
Signed-off-by: NMarcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

- This isn't triggered yet on a normal kernel, because it still does a VT
switch, but it seemed like a good idea to fix this now.
Tested-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NMaarten Maathuis <madman2003@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Mutliple issues.  INIT_ZM_I2C_BYTE/INIT_I2C_BYTE didn't even try and
use the register value, and all the handlers were using the wrong
slave address.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

It appears to be meant to reference the second "default index".
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We may not have parsed the entry yet if the i2c_index is for an i2c bus
that's not referenced by a DCB encoder.

This could be done oh so much more nicely, except we have to care about
prehistoric DCB tables too, and they make life painful.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Some handlers don't report specific errors, but we still *really* want to
know if we failed to parse a complete init table.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We really want to be able to distinguish between INIT_DONE and an actual
error sometimes.  This commit fixes up several lazy "return 0;" to be
actual error codes, and explicitly reserves "0" as "success, but stop
parsing this table".
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

There appears to be some kind of switch on certain chips to control whether
the DP auxch or traditional i2c bus will be operational on a connector,
this commit hopefully fixes nouveau to do the right thing.

Likely only relevent on chips with DP outputs.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

I actually thought these were gone already when the initial commit was
done.. I guess not!
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NMarcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NMarcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reported-by: Dan Carpenter
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Use radeon hpd enum consistently (in both hotplug and dp)
- Legacy r100 with DVI should be HPD_1 not NONE
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Some LVDS connectors don't have a ddc bus, so reset the
ddc bus to invalid before parsing the next connector
to avoid using stale ddc bus data.  Should fix
fdo bug 28164.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

print an error if these fail.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch is a combination of the previous two profile
patches, but without the index bugs.  It cleans up and
fixes some issues with pm profile setup on r6xx chips.
Some tables have different orderings for the power states,
also, r600 only has 1 clock mode per power state. On
desktop cards there are no battery modes, so the low and high
power states are the same.  For the low profile case, choose
the lower clock mode.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Separate dynpm and profile based power management methods.  You can select the pm method
  by echoing the selected method ("dynpm" or "profile") to power_method in sysfs.
- Expose basic 4 profile in profile method
  "default" - default clocks
  "auto" - select between low and high based on ac/dc state
  "low" - DC, low power mode
  "high" - AC, performance mode
  The current base profile is "default", but it should switched to "auto" once we've tested
  on more systems.  Switching the state is a matter of echoing the requested profile to
  power_profile in sysfs.  The lowest power states are selected automatically when dpms turns
  the monitors off in all states but default.
- Remove dynamic fence-based reclocking for the moment.  We can revisit this later once we
  have basic pm in.
- Move pm init/fini to modesetting path.  pm is tightly coupled with display state.  Make sure
  display side is initialized before pm.
- Add pm suspend/resume functions to make sure pm state is properly reinitialized on resume.
- Remove dynpm module option.  It's now selectable via sysfs.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The lowest power states often cause display problems, so only enable
them when all displays are off.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

GUI idle interrupts don't seem to work terribly well on r500 and earlier,
so let's use a fence instead.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We need to handle the ring while we've already locked it, so split out
the allocation and commit functions in order to allow them to be used.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

voltage drop, dynamic voltage, dynamic sclk, pcie lane adjust, etc,
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

voltage drop, dynamic voltage, dynamic sclk, pcie lane adjust, etc,
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

since derefing the object might free it.
Signed-off-by: NDave Airlie <airlied@redhat.com>

- disable gui idle interrupt use
  Seems to hang some r5xx chips
- move vbl range check into
  existing vbl check function in
  radeon_pm.c
- disable crtc mc acccess for the
  whole reclocking process
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>