The mlxsw driver relies on NETDEV_CHANGEUPPER events to configure the
device in case a port is enslaved to a master netdev such as bridge or
bond.

Since the driver ignores events unrelated to its ports and their
uppers, it's possible to engineer situations in which the device's data
path differs from the kernel's.

One example to such a situation is when a port is enslaved to a bond
that is already enslaved to a bridge. When the bond was enslaved the
driver ignored the event - as the bond wasn't one of its uppers - and
therefore a bridge port instance isn't created in the device.

Until such configurations are supported forbid them by checking that the
upper device doesn't have uppers of its own.

Fixes: 0d65fc13 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NNogah Frankel <nogahf@mellanox.com>
Tested-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

wl1251: add a missing spin_lock_init()

This fixes the following kernel warning:

 [ 5668.771453] BUG: spinlock bad magic on CPU#0, kworker/u2:3/9745
 [ 5668.771850]  lock: 0xce63ef20, .magic: 00000000, .owner: <none>/-1,
 .owner_cpu: 0
 [ 5668.772277] CPU: 0 PID: 9745 Comm: kworker/u2:3 Tainted: G        W
 4.12.0-03002-gec979a4-dirty #40
 [ 5668.772796] Hardware name: Nokia RX-51 board
 [ 5668.773071] Workqueue: phy1 wl1251_irq_work
 [ 5668.773345] [<c010c9e4>] (unwind_backtrace) from [<c010a274>]
 (show_stack+0x10/0x14)
 [ 5668.773803] [<c010a274>] (show_stack) from [<c01545a4>]
 (do_raw_spin_lock+0x6c/0xa0)
 [ 5668.774230] [<c01545a4>] (do_raw_spin_lock) from [<c06ca578>]
 (_raw_spin_lock_irqsave+0x10/0x18)
 [ 5668.774658] [<c06ca578>] (_raw_spin_lock_irqsave) from [<c048c010>]
 (wl1251_op_tx+0x38/0x5c)
 [ 5668.775115] [<c048c010>] (wl1251_op_tx) from [<c06a12e8>]
 (ieee80211_tx_frags+0x188/0x1c0)
 [ 5668.775543] [<c06a12e8>] (ieee80211_tx_frags) from [<c06a138c>]
 (__ieee80211_tx+0x6c/0x130)
 [ 5668.775970] [<c06a138c>] (__ieee80211_tx) from [<c06a3dbc>]
 (ieee80211_tx+0xdc/0x104)
 [ 5668.776367] [<c06a3dbc>] (ieee80211_tx) from [<c06a4af0>]
 (__ieee80211_subif_start_xmit+0x454/0x8c8)
 [ 5668.776824] [<c06a4af0>] (__ieee80211_subif_start_xmit) from
 [<c06a4f94>] (ieee80211_subif_start_xmit+0x30/0x2fc)
 [ 5668.777343] [<c06a4f94>] (ieee80211_subif_start_xmit) from
 [<c0578848>] (dev_hard_start_xmit+0x80/0x118)
...

    by adding the missing spin_lock_init().
Reported-by: NPavel Machek <pavel@ucw.cz>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 7ad813f2 ("net: phy:
Correctly process PHY_HALTED in phy_stop_machine()") because it is
creating the possibility for a NULL pointer dereference.

David Daney provide the following call trace and diagram of events:

When ndo_stop() is called we call:

 phy_disconnect()
    +---> phy_stop_interrupts() implies: phydev->irq = PHY_POLL;
    +---> phy_stop_machine()
    |      +---> phy_state_machine()
    |              +----> queue_delayed_work(): Work queued.
    +--->phy_detach() implies: phydev->attached_dev = NULL;

Now at a later time the queued work does:

 phy_state_machine()
    +---->netif_carrier_off(phydev->attached_dev): Oh no! It is NULL:

 CPU 12 Unable to handle kernel paging request at virtual address
0000000000000048, epc == ffffffff80de37ec, ra == ffffffff80c7c
Oops[#1]:
CPU: 12 PID: 1502 Comm: kworker/12:1 Not tainted 4.9.43-Cavium-Octeon+ #1
Workqueue: events_power_efficient phy_state_machine
task: 80000004021ed100 task.stack: 8000000409d70000
$ 0   : 0000000000000000 ffffffff84720060 0000000000000048 0000000000000004
$ 4   : 0000000000000000 0000000000000001 0000000000000004 0000000000000000
$ 8   : 0000000000000000 0000000000000000 00000000ffff98f3 0000000000000000
$12   : 8000000409d73fe0 0000000000009c00 ffffffff846547c8 000000000000af3b
$16   : 80000004096bab68 80000004096babd0 0000000000000000 80000004096ba800
$20   : 0000000000000000 0000000000000000 ffffffff81090000 0000000000000008
$24   : 0000000000000061 ffffffff808637b0
$28   : 8000000409d70000 8000000409d73cf0 80000000271bd300 ffffffff80c7804c
Hi    : 000000000000002a
Lo    : 000000000000003f
epc   : ffffffff80de37ec netif_carrier_off+0xc/0x58
ra    : ffffffff80c7804c phy_state_machine+0x48c/0x4f8
Status: 14009ce3        KX SX UX KERNEL EXL IE
Cause : 00800008 (ExcCode 02)
BadVA : 0000000000000048
PrId  : 000d9501 (Cavium Octeon III)
Modules linked in:
Process kworker/12:1 (pid: 1502, threadinfo=8000000409d70000,
task=80000004021ed100, tls=0000000000000000)
Stack : 8000000409a54000 80000004096bab68 80000000271bd300 80000000271c1e00
        0000000000000000 ffffffff808a1708 8000000409a54000 80000000271bd300
        80000000271bd320 8000000409a54030 ffffffff80ff0f00 0000000000000001
        ffffffff81090000 ffffffff808a1ac0 8000000402182080 ffffffff84650000
        8000000402182080 ffffffff84650000 ffffffff80ff0000 8000000409a54000
        ffffffff808a1970 0000000000000000 80000004099e8000 8000000402099240
        0000000000000000 ffffffff808a8598 0000000000000000 8000000408eeeb00
        8000000409a54000 00000000810a1d00 0000000000000000 8000000409d73de8
        8000000409d73de8 0000000000000088 000000000c009c00 8000000409d73e08
        8000000409d73e08 8000000402182080 ffffffff808a84d0 8000000402182080
        ...
Call Trace:
[<ffffffff80de37ec>] netif_carrier_off+0xc/0x58
[<ffffffff80c7804c>] phy_state_machine+0x48c/0x4f8
[<ffffffff808a1708>] process_one_work+0x158/0x368
[<ffffffff808a1ac0>] worker_thread+0x150/0x4c0
[<ffffffff808a8598>] kthread+0xc8/0xe0
[<ffffffff808617f0>] ret_from_kernel_thread+0x14/0x1c

The original motivation for this change originated from Marc Gonzales
indicating that his network driver did not have its adjust_link callback
executing with phydev->link = 0 while he was expecting it.

PHYLIB has never made any such guarantees ever because phy_stop() merely just
tells the workqueue to move into PHY_HALTED state which will happen
asynchronously.
Reported-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reported-by: NDavid Daney <ddaney.cavm@gmail.com>
Fixes: 7ad813f2 ("net: phy: Correctly process PHY_HALTED in phy_stop_machine()")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BCM7278 has only 128 entries while BCM7445 has the full 256 entries set,
fix that.

Fixes: 7318166c ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cq_period_mode assignment was mistakenly removed so it was always set to "0",
which is EQE based moderation, regardless of the device CAPs and
requested value in ethtool.

Fixes: 6a9764ef ("net/mlx5e: Isolate open_channels from priv->params")
Signed-off-by: NTal Gilboa <talgi@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fix inline header size, make sure it is not greater than skb len.
This bug effects small packets, for example L2 packets with size < 18.

Fixes: ae76715d ("net/mlx5e: Check the minimum inline header mode before xmit")
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When changing from switchdev to legacy mode, all the representor port
devices (uplink nic and reps) are cleaned up. Part of this cleaning
process is removing the neigh entries and the hash table containing them.
However, a representor neigh entry might be linked to the uplink port
hash table and if the uplink nic is cleaned first the cleaning of the
representor will end up in null deref.
Fix that by unloading the representors in the opposite order of load.

Fixes: cb67b832 ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: NShahar Klein <shahark@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently if vxlan tunnel ipv6 src isn't supplied the driver fails to
resolve it as part of the route lookup. The resulting encap header
is left with a zeroed out ipv6 src address so the packets are sent
with this src ip.

Use an appropriate route lookup API that also resolves the source
ipv6 address if it's not supplied.

Fixes: ce99f6b9 ('net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels')
Signed-off-by: NPaul Blakey <paulb@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently, increasing the number of combined channels is changing
the RSS spread to use the new created channels.
Prevent the RSS spread change in case the user explicitly declare it,
to avoid overriding user configuration.

Tested:
when RSS default:

# ethtool -L ens8 combined 4
RSS spread will change and point to 4 channels.

# ethtool -X ens8 equal 4
# ethtool -L ens8 combined 6
RSS will not change after increasing the number of the channels.

Fixes: 8bf36862 ('ethtool: ensure channel counts are within bounds during SCHANNELS')
Signed-off-by: NInbar Karmy <inbark@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Function mlx5e_dealloc_rx_wqe is using page pointer value as an
indication to valid DMA mapping. In case that the mapping failed, we
released the page but kept the dangling pointer. Store the page pointer
only after the DMA mapping passed to avoid invalid page DMA unmap.

Fixes: bc77b240 ("net/mlx5e: Add fragmented memory support for RX multi packet WQE")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

MLX5_INTERFACE_STATE_SHUTDOWN is not used in the code.

Fixes: 5fc7197d ("net/mlx5: Add pci shutdown callback")
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

There is an issue where the firmware fails during mlx5_load_one,
the health_care timer detects the issue and schedules a health_care call.
Then the mlx5_load_one detects the issue, cleans up and quits. Then
the health_care starts and calls mlx5_unload_one to clean up the resources
that no longer exist and causes kernel panic.

The root cause is that the bit MLX5_INTERFACE_STATE_DOWN is not set
after mlx5_load_one fails. The solution is removing the bit
MLX5_INTERFACE_STATE_DOWN and quit mlx5_unload_one if the
bit MLX5_INTERFACE_STATE_UP is not set. The bit MLX5_INTERFACE_STATE_DOWN
is redundant and we can use MLX5_INTERFACE_STATE_UP instead.

Fixes: 5fc7197d ("net/mlx5: Add pci shutdown callback")
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Support for ISSI version 0 was recently broken as the arm_srq_cmd
command, which is used only for ISSI version 0, was given the opcode
for ISSI version 1 instead of ISSI version 0.

Change arm_srq_cmd to use the correct command opcode for ISSI version
0.

Fixes: af1ba291 ('{net, IB}/mlx5: Refactor internal SRQ API')
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Current code doesn't report DCB_CAP_DCBX_HOST capability when query
through getcap. User space lldptool expects capability to have HOST mode
set when it wants to configure DCBX CEE mode. In absence of HOST mode
capability, lldptool fails to switch to CEE mode.

This fix returns DCB_CAP_DCBX_HOST capability when port's DCBX
controlled mode is under software control.

Fixes: 3a6a931d ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

qos capability is the master capability bit that determines
if the DCBX is supported for the PCI function. If this bit is off,
driver cannot run any dcbx code.

Fixes: e207b7e9 ("net/mlx5e: ConnectX-4 firmware support for DCBX")
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

It is quite common for ti_cm_get_macid() to fail on some of the
platforms it is invoked on. They include any platform where
mac address is not part of SoC register space.

On these platforms, mac address is read and populated in
device-tree by bootloader. An example is TI DA850.

Downgrade the severity of message to "information", so it does
not spam logs when 'quiet' boot is desired.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy is connected at early stage of probe but not properly
disconnected if error occurs.  This patch fixes the issue.

Also changing the return type of xgene_enet_check_phy_handle(),
since this function always returns success.
Signed-off-by: NQuan Nguyen <qnguyen@apm.com>
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both the nfp_net_pf_app_start() and the nfp_net_pci_probe() functions
call nfp_net_pf_app_stop_ctrl(pf) so there is a double free.  The free
should be done from the probe function because it's allocated there so
I have removed the call from nfp_net_pf_app_start().

Fixes: 02082701 ("nfp: create control vNICs and wire up rx/tx")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should inform user about wrong firmware version
by printing message in dmesg.

Fixes: 3d2ff7eebe26 ("net: ethernet: aquantia: Atlantic hardware abstraction layer")
Signed-off-by: NPavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the HW supports up to 32 multicast filters we should
track count of multicast filters to avoid overflow.
If we attempt to add >32 multicast filter - just set NETIF_ALLMULTI flag
instead.

Fixes: 94f6c9e4cdf6 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: NIgor Russkikh <Igor.Russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver choose the optimal interrupt throttling settings depends
of current link speed.
Due this bug link_status field from aq_hw is never updated and as result
always used same interrupt throttling values.

Fixes: 3d2ff7eebe26 ("net: ethernet: aquantia: Atlantic hardware abstraction layer")
Signed-off-by: NPavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware has the HW Checksum Offload bug when small
TCP patckets (with length <= 60 bytes) has wrong "checksum valid" bit.

The solution is - ignore checksum valid bit for small packets
(with length <= 60 bytes) and mark this as CHECKSUM_NONE to allow
network stack recalculate checksum itself.

Fixes: ccf9a5ed14be ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.")
Signed-off-by: NPavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The number of RSS queues should be not more than numbers of CPU.
Its does not make sense to increase perfomance, and also cause problems on
some motherboards.

Fixes: 94f6c9e4cdf6 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: NPavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes datapath spinlocks which does not perform any
useful work.

Fixes: 6e70637f9f1e ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: NPavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Passing commands for logging to t4_record_mbox() with size
MBOX_LEN, when the actual command size is actually smaller,
causes out-of-bounds stack accesses in t4_record_mbox() while
copying command words here:

	for (i = 0; i < size / 8; i++)
		entry->cmd[i] = be64_to_cpu(cmd[i]);

Up to 48 bytes from the stack are then leaked to debugfs.

This happens whenever we send (and log) commands described by
structs fw_sched_cmd (32 bytes leaked), fw_vi_rxmode_cmd (48),
fw_hello_cmd (48), fw_bye_cmd (48), fw_initialize_cmd (48),
fw_reset_cmd (48), fw_pfvf_cmd (32), fw_eq_eth_cmd (16),
fw_eq_ctrl_cmd (32), fw_eq_ofld_cmd (32), fw_acl_mac_cmd(16),
fw_rss_glb_config_cmd(32), fw_rss_vi_config_cmd(32),
fw_devlog_cmd(32), fw_vi_enable_cmd(48), fw_port_cmd(32),
fw_sched_cmd(32), fw_devlog_cmd(32).

The cxgb4vf driver got this right instead.

When we call t4_record_mbox() to log a command reply, a MBOX_LEN
size can be used though, as get_mbox_rpl() will fill cmd_rpl up
completely.

Fixes: 7f080c3f ("cxgb4: Add support to enable logging of firmware mailbox commands")
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the bindings have been controversial, and we follow the DT stable ABI
rule, we shouldn't let a driver with a DT binding that might change slip
through in a stable release.

Remove the compatibles to make sure the driver will not probe and no-one
will start using the binding currently implemented. This commit will
obviously need to be reverted in due time.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously the vlan tci field was incorrectly exact matched. This patch
fixes this by using the flow dissector to populate the vlan tci field.

Fixes: 5571e8c9 ("nfp: extend flower matching capabilities")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously when calculating the supported key layers MPLS, IPv4/6
TTL and TOS were not considered. This patch checks that the TTL and
TOS fields are masked out before offloading. Additionally this patch
checks that MPLS packets are correctly handled, by not offloading them.

Fixes: af9d842c ("nfp: extend flower add flow offload")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously flow dissectors were referenced without first checking that
they are in use and correctly populated by TC. This patch fixes this by
checking each flow dissector key before referencing them.

Fixes: 5571e8c9 ("nfp: extend flower matching capabilities")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mac address is only retrieved from h/w when using PPv2.1. Otherwise
the variable holding it is still checked and used if it contains a valid
value. As the variable isn't initialized to an invalid mac address
value, we end up with random mac addresses which can be the same for all
the ports handled by this PPv2 driver.

Fixes this by initializing the h/w mac address variable to {0}, which is
an invalid mac address value. This way the random assignation fallback
is called and all ports end up with their own addresses.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Fixes: 26975821 ("net: mvpp2: handle misc PPv2.1/PPv2.2 differences")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The u-blox TOBY-L4 is a LTE Advanced (Cat 6) module with HSPA+ and 2G
fallback.

Unlike the TOBY-L2, this module has one single USB layout and exposes
several TTYs for control and a NCM interface for data. Connecting this
module may be done just by activating the desired PDP context with
'AT+CGACT=1,<cid>' and then running DHCP on the NCM interface.
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check memory allocation failure and return -ENOMEM in such a case, as
already done few lines below for another memory allocation.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rtl_tx() is the TX reclamation process whereas rtl8169_tx_clear_range() does
the TX ring cleaning during shutdown, both of these functions should call
dev_consume_skb_any() to be drop monitor friendly.

Fixes: cac4b22f ("r8169: do not account fragments as packets")
Fixes: eb781397 ("r8169: Do not use dev_kfree_skb in xmit path")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rtl8169_tx_clear_range() is responsible for cleaning up the TX ring
during interface shutdown, incrementing tx_dropped for every SKB that we
left at the time in the ring is misleading.

Fixes: cac4b22f ("r8169: do not account fragments as packets")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a deadlock possible when canceling the link status
delayed work queue. The removal process is run with RTNL held,
and the link status callback is acquring RTNL.

Resolve the issue by using trylock and rescheduling.
If cancel is in process, that block it from happening.

Fixes: 122a5f64 ("staging: hv: use delayed_work for netvsc_send_garp()")
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case bcm_sysport_init_tx_ring() is not able to allocate ring->cbs, we
would return with an error, and call bcm_sysport_fini_tx_ring() and it
would see that ring->cbs is NULL and do nothing. This would leak the
coherent DMA descriptor area, so we need to free it on error before
returning.
Reported-by: NEric Dumazet <edumazet@gmail.com>
Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are 3 spots where we call dev_kfree_skb() but we are actually
just doing a normal SKB consumption: __bcmgenet_tx_reclaim() for normal
TX reclamation, bcmgenet_alloc_rx_buffers() during the initial RX ring
setup and bcmgenet_free_rx_buffers() during RX ring cleanup.

Fixes: d6707bec ("net: bcmgenet: rewrite bcmgenet_rx_refill()")
Fixes: f48bed16 ("net: bcmgenet: Free skb after last Tx frag")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Utilize dev_consume_skb_any(cb->skb) in bcm_sysport_free_cb() which is
used when a TX packet is completed, as well as when the RX ring is
cleaned on shutdown. None of these two cases are packet drops, so be
drop monitor friendly.
Suggested-by: NEric Dumazet <edumazet@gmail.com>
Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc-8.0.0 (snapshot) points out that we copy a variable-length string
into a fixed length field using memcpy() with the destination length,
and that ends up copying whatever follows the string:

    inlined from 'ql_core_dump' at drivers/net/ethernet/qlogic/qlge/qlge_dbg.c:1106:2:
drivers/net/ethernet/qlogic/qlge/qlge_dbg.c:708:2: error: 'memcpy' reading 15 bytes from a region of size 14 [-Werror=stringop-overflow=]
  memcpy(seg_hdr->description, desc, (sizeof(seg_hdr->description)) - 1);

Changing it to use strncpy() will instead zero-pad the destination,
which seems to be the right thing to do here.

The bug is probably harmless, but it seems like a good idea to address
it in stable kernels as well, if only for the purpose of building with
gcc-8 without warnings.

Fixes: a61f8026 ("qlge: Add ethtool register dump function.")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change is needed to not fool drop monitor.
(perf record ... -e skb:kfree_skb )

Packets were properly sent and are consumed after TX completion.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>