This does not work with multiple sta's in a vif.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For consistency with other code.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

While poking at this I also change two related things. I rename one
variable to make the names consistent. I also move one assignment of
priv_sta to the declaration to save a few lines.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some code used priv_vif and some used vif_priv. Convert all to vif_priv
for consistency.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Makes the code a little easier to read.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The wcn36xx FW expects a fixed size TIM PVM in the beacon template. If
supplied with a shorter than expected PVM it will overwrite the IE
following the TIM.

Squashed with fix from Jason Mobarak <jam@cozybit.com>:
Patch "wcn36xx: Pad TIM PVM if needed" has caused a regression in mesh
beaconing.  The field tim_off is always 0 for mesh mode, and thus
pvm_len (referring to the TIM length field) and pad are both incorrectly
calculated.  Thus, msg_body.beacon_length is incorrectly calculated for
mesh mode. Fix this.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJason Mobarak <jam@cozybit.com>
[bjorn: squashed in Jason's fixup]
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Needed for coming improvements. No functional changes.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
[bjorn: restored BEACON_TEMPLATE_SIZE define to 0x180]
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The Wistron DNMA-92 and Compex WLM200NX have inverted LED polarity
(active high instead of active low).

The same PCI Subsystem ID is used by both cards, which are based on
the same Atheros MB92 design.

Cc: <linux-wireless@vger.kernel.org>
Cc: <ath9k-devel@qca.qualcomm.com>
Cc: <ath9k-devel@lists.ath9k.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NVittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The LED can be active high instead of active low on some hardware.

Add the led_active_high module parameter. It defaults to -1 to obey
platform data as before.

Setting the parameter to 1 or 0 will force the LED respectively
active high or active low.

Cc: <linux-wireless@vger.kernel.org>
Cc: <ath9k-devel@qca.qualcomm.com>
Cc: <ath9k-devel@lists.ath9k.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NVittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It's not needed for anything so just get rid of it.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Now that all firmware-N.bin related are within struct ath10k_fw_file we can
switch to use ath10k_core_fetch_firmware_api_n() and delete almost identical
ath10k_tm_fetch_utf_firmware_api_2().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Preparation for testmode.c to use ath10k_core_fetch_board_data_api_n().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Preparation for testmode.c to use ath10k_core_fetch_board_data_api_n().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Preparation for testmode.c to use ath10k_core_fetch_board_data_api_n().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Preparation for testmode.c to use ath10k_core_fetch_board_data_api_n().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To make it easier to share ath10k_core_fetch_board_data_api_n() with testmode.c
refactor all firmware components to struct ath10k_fw_components. This structure
will hold firmware related files, for example firmware-N.bin and board-N.bin.

For firmware-N.bin create a new struct ath10k_fw_file which contains the actual
firmware image as well as the parsed data from the image.

Modify ath10k_core_start() to take struct ath10k_fw_components() as an argument
which makes it possible in following patches to drop some ugly hacks from
testmode.c.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This has ben deprecated years ago, I haven't heard anyone using it since and
most likely it won't even work anymore. So just remove all of it.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ah is written twice with the same value, remove one of the
redundant assignments to ah.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Tx power limitations at upper layers are interpreted in
the EIRP domain. When the user requests a given maximum
txpower, e.g. with: 'iw phy0 set txpower fixed 1500',
he expects the EIRP to be at or below 15dBm.

In ath9k_hw_apply_txpower(), the interpretation is
different: the antenna-gain is capped against the
current txpower limit in the regulatory, but not
against the user set value. It ensures that the
resulting EIRP is below the limit defined by the
active countrycode, but not below the value the
user requested.

In a scenario like e.g.
 a) antenna_gain=6
 b) countrycode limits to eirp=18
 c) user set txpower=15
this will cause a setting for AR_PHY_POWER_TX_RATE
regs resulting in an EIRP > 15.

This patch ensures that antenna-gain is considered
whenever the txpower limit is adjusted and with that
the user set limits are kept.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Replace an explicit initialisation for one local variable at the beginning
by a conditional assignment.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Reviewed-by: NOleksij Rempel <linux@rempel-privat.de>
Reviewed-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

push-pull mode needs certain amount the host driver involvement for
managing queues in the host memory and packet delivery to firmware.
qca4019 wifi firmware has an option to stay in push mode for less
number of active traffic flow and then switch to push-pull mode when
the active traffic flow goes beyond the certain limit.

The advantage of staying in push mode for less active traffic is, the
host cpu consumption is reduced. qca4019 firmware supports this
flexibility of the mode switch. It takes the host driver interest
(LOW_PERF/HIGH_PERF) via WMI_EXT_RESOURCE_CFG_CMDID,

 LOW_PERF  - fw would stay in push mode and switch to push-pull
               based on demand.
 HIGH_PERF - fw would stay in push-pull mode from the boot.

To make this configuration generic, new WMI services
WMI_SERVICE_TX_MODE_PUSH_ONLY, WMI_SERVICE_TX_MODE_PUSH_PULL,
WMI_SERVICE_TX_MODE_DYNAMIC are introduced to take dynamic tx mode
switch support availability in firmware.
Based on WMI_SERVICE_TX_MODE_DYNAMIC, LOW_PERF or HIGHT_PERF is
configured to the firmware.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NTamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Smatch complains that since "ev->peer_id" comes from skb->data that
means we can't trust it and have to do a bounds check on it to prevent
an array overflow.

Fixes: 6942726f ('ath10k: add fast peer_map lookup')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Upon firmware assert, restart work will be triggered so that mac80211
will reconfigure the driver. An issue is reported that after restart
work, survey dump data do not contain in-use (SURVEY_INFO_IN_USE) info
for operating channel. During reconfigure, since mac80211 already has
valid channel context for given radio, channel context iteration return
num_chanctx > 0. Hence rx_channel is always NULL. Fix this by assigning
channel context to rx_channel when driver restart is in progress.

Cc: stable@vger.kernel.org
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Return value is incorrect for btcoex and peer stats debugfs
'write' entries if the user provides a value that matches with
the already available debugfs entry, this results in the debugfs
entry getting stuck and the operation has to be terminated manually.
Fix this by returning the appropriate return 'count' as we do it for
other debugfs entries like pktlog etc.

Fixes: cc61a1bb ("ath10k: enable debugfs provision to enable Peer Stats feature")
Fixes: c28e6f06 ("ath10k: fix sanity check on enabling btcoex via debugfs")
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Found by checkpatch:

drivers/net/wireless/ath/ath10k/mac.c:6800: Alignment should match open parent
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warning:

drivers/net/wireless/ath/ath10k/wmi.c:5800: Prefer ether_addr_copy() over memcpy() if the Ethernet addresses are __aligned(2)
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

drivers/net/wireless/ath/ath10k/mac.c:452: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
drivers/net/wireless/ath/ath10k/mac.c:455: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
drivers/net/wireless/ath/ath10k/txrx.c:133: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

drivers/net/wireless/ath/ath10k/htt.h:1477: Prefer kernel type 'u64' over 'u_int64_t'
drivers/net/wireless/ath/ath10k/htt.h:1480: Prefer kernel type 'u64' over 'u_int64_t'
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix checkpatch warnings about use of spaces with operators:

spaces preferred around that '*' (ctx:VxV)

This has been recently added to checkpatch.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

MSI-X is never well-tested, might contain bugs and generally isn't
really all that useful to maintain. Also ath10k is mainly used with
shared/singly-MSI interrupt systems. Hence removing MSI range support.
This change will be useful for further cleanup in copy engine lock
and to add NAPI support.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 firmware has addeded set_tsf vdev parameter,
hence enable it.
set_tsf function can be used to shift TBTT that will
help avoid its clockdrift which happens when beacons
are collided.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Update 10.4 WMI vdev param to sync to current 10.4 firmware
as of 2/23/2016.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.2.4.70.24 firmware introduces new feature to set TSF
via vdev parameter, hence implement relevant function.
set_tsf function can be used to shift TBTT that will
help avoid its clockdrift which happens when beacons
are collided.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This will help anyone trying to use the ack-rssi reporting
feature with the host-specified TX-rate option in 10.4 firmware.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Merge tag 'wireless-drivers-next-for-davem-2016-04-11' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers patches for 4.7

Major changes:

iwlwifi

* support for Link Quality measurement
* more work 9000 devices and MSIx
* continuation of the Dynamic Queue Allocation work
* make the paging less memory hungry
* 9000 new Rx path
* removal of IWLWIFI_UAPSD Kconfig option

ath10k

* implement push-pull tx model using mac80211 software queuing support
* enable scan in AP mode (NL80211_FEATURE_AP_SCAN)

wil6210

* add basic PBSS (Personal Basic Service Set) support
* add initial P2P support
* add oob_mode module parameter
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

verifier is using the following structure to track the state of registers:
struct reg_state {
    enum bpf_reg_type type;
    union {
        int imm;
        struct bpf_map *map_ptr;
    };
};
and later on in states_equal() does memcmp(&old->regs[i], &cur->regs[i],..)
to find equivalent states.
Throughout the code of verifier there are assignements to 'imm' and 'map_ptr'
fields and it's not obvious that most of the assignments into 'imm' don't
need to clear extra 4 bytes (like mark_reg_unknown_value() does) to make sure
that memcmp doesn't go over junk left from 'map_ptr' assignment.

Simplify the code by converting 'int' into 'long'
Suggested-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A stupid refactoring bug in inet6_lookup_listener() needs to be fixed
in order to get proper SO_REUSEPORT behavior.

Fixes: 3b24d854 ("tcp/dccp: do not touch listener sk_refcnt under synflood")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NMaciej Żenczykowski <maze@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull tty fixes from Greg KH:
 "Here are two tty fixes for issues found.

  One was due to a merge error in 4.6-rc1, and the other a regression
  fix for UML consoles that broke in 4.6-rc1.

  Both have been in linux-next for a while"

* tag 'tty-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: Fix merge of "tty: Refactor tty_open()"
  tty: Fix UML console breakage