This fixes a regression caused by commit
d3557fc8 megaraid_sas : Add separate function
for setting up IRQs This makes boot end with 'root does not exist' message on
certain adapters.

The bug is that the driver does not setup ints for cards without msi-x
support.  This patch fixes it, in addition to that it moves tasklet
initialisation before enable_intr, otherwise a kernel panic may occur, when an
interrupt arrives before the tasklet is ready.
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The domain controller PLOGI's concurrent with prior LOGO's/unreg_rpi's
completing created a race condition where driver rpi ref count can
inadvertantly hit 0 and the rpi attempted to be freed. This error
sometimes resulted in Warning messages indicating kref.h via
lfpc_nlp_get+0x128.

Correct by dropping any new PLOGI until the prior nport state has settled.
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

TMF's were getting error messages on FCP_RSP errors (underrun). Underruns
aren't meaningful in the scenario. Change the error message to filter out
these response check errors, and don't unconditionally mark the cmd as
in error.
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The driver inadvertainly constrained the id space to 8 bits, when its
a full 16 bits from hw. This resulted in bad id's being written to the
hardware. Resulted in symptoms such as incomplete initialization, no
detection of link events, etc.
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Didn't check for less-than-or-equal zero. Means we may later call
scsi_dma_unmap() even though we don't have valid mappings.
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

With blk-mq support in the mid-layer, lpfc can do IO steering based
on the information in the request tag.  This patch allows lpfc to use
blk-mq if enabled. If not enabled, we fall back into the emulex-internal
affinity mappings.

This feature can be turned on via CONFIG_SCSI_MQ_DEFAULT or passing
scsi_mod.use_blk_mq=Y as a parameter to the kernel.
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

When a remote nport changes it's DID, a new ndlp is used.
However, we left the old ndlp state unchanged and still in
a discovery state. The may stall discovery resulting in some
devices not being discovered.  Correct by swapping the state
of the 2 ndlp's when a DID swap is detected.
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

If a vport was deleted while in the middle of discovery, we weren't
clearing the nport discovery flag. Correct by clearing the flag and
cancelling our discovery timeout timer.
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

LCB requests to set Beacon would fail if the beacon was already enabled
internally as the mailbox command used to query the state failes with
an already-set status.

Correct by enhancing the check so we don't fail if if the already set
status comes back.
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Correct locking and refcounting in tracking our rports
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

We inadvertantly took the path to recreate the vport while in a
driver teardown path
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Also has a little whitespace fixing.
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Fix incorrect reference counting
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The order (it's a shall, but hard to dictate after the fact) is given in
FC-SCM - kind of.  SCM indicates what shall be implemented, lists it as (a),
(b), (c), but actually doesn't say it has to be in that order.  The only hard
requirement, called out in FCP-4, is that you must register your FC-4 Type
(via RFT_ID) before registering FC-4 Type Features (via RFF_ID), which makes
sense. We obviously violated this and there were some switches (or newer fw in
them) that enforced it.  The other rule of thumbs are: register your data with
the switch first, then register for SCRs, then do queries about the fabric,
with the SCRs telling you of changes post the queries.
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NSebastian Herbszt <herbszt@gmx.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NNicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

When creating a new endpoint, we look for a free id
for the new endpoint. We baisically loop on possible ids
and use the first id that class_find_device() returns NULL.
However, we are missing a reference put when class_find_device()
does find an existing device for a given id.
Reported-by: NAlex Lyakas <alex@zadarastorage.com>
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

non-x86 builds want the #warning in the IPS code about compiling on the wrong
architecture removed because it keeps triggering on their platforms build
farms.  Transform from a compile time warning into a runtime one with taint to
preserve the original intent of the authors.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The driver waits for command completion event while cleanup of task
within the frwd lock and back locks. The frwd lock was still held
which caused the call trace while issuing a device reset.
Release the frwd lock along with the back lock
to avoid waiting in the lock context.
Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Fix the firmware assert, during target logout in
case driver received FIN from target before waiting for
asyncronous response.
Signed-off-by: NTej Parkash <tej.parkash@qlogic.com>
Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Newer revisions of QUALCOMM Technologies UFS host controller may not
advertise the correct version information in UFS HCI VER register.
To handle this, enable UFSHCD_QUIRK_BROKEN_UFS_HCI_VERSION to let
UFS standard host controller driver call into vendor specific
operation to get right UFS HCI VER register value.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Some host controller hardware controllers may not advertise correct
version in UFS HCI VER register. To workaround this, add new quirk
and call the host controller hardware vendor specific callback to
get the correct UFS HCI version register value.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Current version of host controller on QUALCOMM Technologies requires
this quirk to be enabled, as DME commands to device must be sent
only in AUTO mode (SLOW AUTO or FAST AUTO).
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Some UFS host controllers may only allow accessing the peer DME attribute
in AUTO mode (FAST AUTO or SLOW AUTO) hence we had added a quirk for
switching to AUTO power mode before accessing the peer DME attribute.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

With the G3 UFS devices, changing gear into HS is failing in UFS host
controllers of version 0x2.
The quirk solves the problem of changing gear into HS by enabling
the attribute that specifies whether or not the inbound Link supports
unterminated line in HS mode.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The attribute PA_RXHSUNTERMCAP specifies whether or not the
inbound Link supports unterminated line in HS mode. enabling this
attribute to 1 fixes moving to HS gear.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

LCC (Line Control Command) are being used for communication between
UFS host and UFS device. But UFS host controller on QUALCOMM
Technologies have an issue with issuing the LCC commands to
UFS device and hence this quirk is enabled in order to to disable
LCC from the host side.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

LCC (Line Control Command) are being used for communication between
UFS host and UFS device.
New commercial UFS devices don't have the issues with LCC processing
but UFS host controller might still have the issue with LCC processing,
hence, added a routine to disable TX LCC on the device.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Current versions of UFS host controllers on QUALCOMM Technologies
have interrupt aggregation logic broken.
Interrupt aggregation may not work if both threshold count and timeout
is enabled. Hence disable interrupt aggregation by enabling
UFSHCD_QUIRK_BROKEN_INTR_AGGR quirk until its fixed in the newer
UFS host controller revisions.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

UFS HCI (Host Controller Interface) allows the transfer requests
interrupts to be aggregated to generate the single interrupt but
this can impact the performance. Hence introduce the capability which
gives choice to use the interrupt aggregation capability or not.
By default interrupt aggregation capability is kept disabled.

This change also introduces a quirk for broken interrupt aggregation
feature, as in some UFS controllers, this feature may not work.
Signed-off-by: NYaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>