Sometimes it's useful to know the FireWire speed of the request that has
just come in to a fw_address_handler callback. As struct fw_request is
opaque we can't peek inside to get the speed out of the struct fw_packet
that's just inside. For example, the SBP-2 spec says:

"The speed at which the block write request to the MANAGEMENT_AGENT
register is received shall determine the speed used by the target for
all subsequent requests to read the initiator’s configuration ROM, fetch
ORB’s from initiator memory or store status at the initiator’s
status_FIFO. Command block ORB’s separately specify the speed for
requests addressed to the data buffer or page table."

[ ANSI T10/1155D Revision 4 page 53/54 ]
Signed-off-by: NChris Boot <bootc@bootc.net>
Acked-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Now that tasks are gone we are guaranteed to only get a single completion
per command, and thus don't need this counter.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Now that tasks are gone we are guaranteed to only get a single completion
per command, and thus don't need this counter.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Now that tasks are gone we are guaranteed to only get a single completion
per command, and thus don't need this counter.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

We can use struct se_cmd for everything it did.  Make sure to pass the S/G
list and data direction to the execution function to ease adding back BIDI
support later on.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Now that we only have a single task per command we can use a direct pointer
to it instead of list.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Simply transport_generic_new_cmd to only allocate a single task.  For normal
unidirection commands nothing changes except that the code is a lot simpler
now.  Any BIDI support that used to work will stop now for the next few
patches at least.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Make CDB emulation work on commands instead of tasks again as a preparation
of removing tasks completely.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Remove the task_sectors field that isn't used anywhere.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Now that we don't split commands the size field in the task is always
equivalent to the one in the CDB, even in cases where we have two tasks
due to a BIDI transfer.  Just refer the the size in the command instead
of duplicating it in the task.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Now that we don't split commands the lba field in the task is always
equivalent to the one in the CDB, even in cases where we have two tasks
due to a BIDI transfer.  Just refer the the lba in the command instead
of duplicating it in the task.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Now that tasks are always the same size as the command there is no need
to rewrite a CDB in common code.  Notw that we keep the separately allocated
CDB in the pscsi and stgt backends for now, to easy reintroducing any
command splitting local to these backends if nessecary.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The SCSI MMC GET_EVENT_STATUS_NOTIFICATION command can be used to find
out about media change, among other things.  This patch adds it to the
command sequencer so that PSCSI CD-ROM passthrough works with modern
Linux guests that issue this command.
Tested-by: NCong Meng <mengcong@cn.ibm.com>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

We can use kcalloc() here instead of kzalloc().  It's better style and
it has overflow checking built in.

Also -ENOMEM is the correct error code for allocation errors.  -1 means
-EPERM.  None of the callers preserve the error codes so it doesn't
matter except as a cleanup.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

We originally changed iscsi to allocate its own buffers just as an
intermediate step to clean up some core buffer allocation mechanisms. Now
we can put it back.

Also had to change allocate_iovecs to use data_length instead of
t_data_nents because iovecs are now allocated before the data buffer, thus
t_data_nents is not yet initialized.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

It appears iscsi is the only one to call this in its cmd submit path, but
it appears to be applicable to all fabrics, and should always be called.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Rename iscsit_build_pdu_and_seq_list to iscsit_do_build_pdu_and_seq_lists

Rename iscsit_do_build_list to iscsit_build_pdu_and_seq_lists

Move code from iscsit_decide_list_to_build into _seq_pdu_list.c, seems
a better fit.

Also update some comments in pdu/seq code for correctness and whitespace.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Redundant, just use iscsi_cmd->se_cmd.data_length once se_cmd is
initialized, or hdr->data_length before then.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

if we can get calls to init_se_cmd, get_sess_cmd, lookup_cmd_lun,
core_alua_check_nonop_delay, and handle_cdb_direct next to each other,
then we can just call target_submit_cmd. This is a step towards that
goal.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Trying to move a bunch of stuff around so iscsi can use target_submit_cmd
someday, and so stuff needs to be in that function directly instead of
hidden, so it can be reordered etc.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch renames a horribly misnamed function that no longer allocate
tasks to something more descriptive for it's modern use in target core.

(nab: Fix up ib_srpt to use this as well ahead of a target_submit_cmd
conversion)
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch includes the handful of squashed patches for target/iscsi from
Andy's original series into lio-core/master code:

*) Make iscsit_add_reject static
*) Remove unused data_offset_end from iscsi_datain_req
*) Remove "#if 0" stubs
*) Rename iscsi_datain_req to cmd_datain_node
*) Cleanups for built_r2ts_for_cmd()
*) Cleanups for Cleanup build_sendtargets_response()
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Immediate queue:

Consolidate down to one switch statement by moving send_tx_data and stuff
from second switch into the first switch, or the functions the first switch
calls.

Response queue:

Do not lock istate_lock except directly around i_state modifications.

Put entire ISTATE_SEND_DATAIN path within first switch statement, in prep
for further refactoring.

All other cases set use_misc = 1 and will not be using sendpage, so just
use send_tx_data for these and set use_misc param to 1.

map_sg, sent_status, use_misc, and se_cmd vars no longer needed.

Then put immediate and response handling in separate functions in order
to get iscsi_target_tx_thread down to where it fits on a page.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

When processing immediate queue, we're switching on a local variable
so it's not necessary to lock around it. However, we are modifying
cmd->i_state in two spots, so lock around those parts only.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

*) Use decoded cmd->immediate_cmd for conditional instead of
   re-examining hdr->opcode
*) Make iscist_dataout_post_crc_passed more legible
*) use max() to reduce code in build_r2ts_for_cmd()
*) Remove CONFIG_SMP and if 0 ifdefs
*) Replace if/goto with a while loop
*) Remove unused conn->tx_immediate_queue and tx_response_queue
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The name change makes it clear this list_head is so the cmd can be an
item in the connection's conn_cmd_list.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Now that all fabrics are converted over to using se_cmd->t_data_sg
directly, we can drop the task sg chaining support.  With the modern
memory allocation in target core, task sg chaining is needless
overhead -- we would split up the main cmd sglist into pieces, and
then splice those pieces back together instead of just using the
original list directly.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

With the modern target core, se_cmd->t_data_sg already points to a
sglist that covers the whole command.  So task_sg chaining is needless
overhead and obfuscation -- instead of splicing the split up task
sglists back into one list, we can just use the original list directly.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

With the modern target core, se_cmd->t_data_sg already points to a
sglist that covers the whole command.  So task_sg chaining is needless
overhead and obfuscation -- instead of splicing the split up task
sglists back into one list, we can just use the original list directly.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NKiran Patil <Kiran.patil@intel.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

From hch:

The high-performance backends (iblock and rd) support tasks of unlimited
size.  With that there is no reason to keep a complex infrastructure for
splitting up commands in place.  Stop doing so and only submit a single
task per data direction.  Once this is in place we can slowly remove fields
from the task that duplicate things in the command, or move other fields
into the command.

From nab:

The benefit to IBLOCK performance by removing the additional
fast-path allocation overhead + SGL mapping to se_task->task_sg[] is now
greater than transparently supporting an received CDB I/O length that
exceeds what is allowed by backend pSCSI LLD hardware max_sectors, that
was originally supported for all backend export cases.

This change may effect some users of pSCSI users on legacy hardware, but
I think most folks are now using TYPE_DISK struct scsi_device export
with IBLOCK.  The only other place where this may can issues that cannot
be resolved with IBLOCK TYPE_DISK is using TYPE_ROM, TYPE_TAPE or other
pSCSI non TYPE_DISK export with an SCSI LLDs using a smaller
max_sectors.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The ramdisk backend has not inherent limitations for handling requests,
so don't artificially limits the transfer size.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Remove various leftovers of the old direct/indirect split, as well as the
unused rd_request structure and a couple unused defines and fields.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The UASP protocol does not inform the target device upfront how much
data it should expect so we have to learn in from the CDB.  So in order
to handle this case, add a TARGET_SCF_UNKNOWN_SIZE to target_submit_cmd()
and perform an explictly assignment for se_cmd->data_length from the
extracted CDB size in transport_generic_cmd_sequencer().
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This was used at one time as a hack by FILEIO backend registration to
allow a struct block_device that was claimed with blkdev_get (by a local
filesystem mount for example) to be exported as read-only (SCSI WP=1).

Since FILEIO backend registration will no longer attempt to obtain
exclusive access to an underlying struct block_device here, this flag is
now obsolete.
Reported-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Pull two more small regmap fixes from Mark Brown:
 - Now we have users for it that aren't running Android it turns out
   that regcache_sync_region() is much more useful to drivers if it's
   exported for use by modules.  Who knew?
 - Make sure we don't divide by zero when doing debugfs dumps of
   rbtrees, not visible up until now because everything was providing at
   least some cache on startup.

* tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: prevent division by zero in rbtree_show
  regmap: Export regcache_sync_region()

Pull a few KVM fixes from Avi Kivity:
 "A bunch of powerpc KVM fixes, a guest and a host RCU fix (unrelated),
  and a small build fix."

* 'kvm-updates/3.4' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: Resolve RCU vs. async page fault problem
  KVM: VMX: vmx_set_cr0 expects kvm->srcu locked
  KVM: PMU: Fix integer constant is too large warning in kvm_pmu_set_msr()
  KVM: PPC: Book3S: PR: Fix preemption
  KVM: PPC: Save/Restore CR over vcpu_run
  KVM: PPC: Book3S HV: Save and restore CR in __kvmppc_vcore_entry
  KVM: PPC: Book3S HV: Fix kvm_alloc_linear in case where no linears exist
  KVM: PPC: Book3S: Compile fix for ppc32 in HIOR access code