In commit 5a7baa78 ("bonding: Advertize vxlan offload features when
supported"), Or Gerlitz added support conditional vxlan offload.

In this patch I also add support for all kind of tunnels,
but we allow a bonding device to not require segmentation,
as it is always better to make this segmentation at the very last stage,
if a particular slave device requires it.

Tested:

 Setup a GRE tunnel,
 on a physical NIC not having tx-gre-segmentation.
 Results on bnx2x are even better, as we no longer have to segment
 in software.

ethtool -K bond0 tx-gre-segmentation off

super_netperf 50 --google-pacing-rate 30000000 -H 10.7.8.152 -l 15
7538.32

ethtool -K bond0 tx-gre-segmentation on

super_netperf 50 --google-pacing-rate 30000000 -H 10.7.8.152 -l 15
10200.5
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Static checkers complain that we should maybe set "ret" before we do the
"goto out;".  They interpret the NULL return from br_port_get_rtnl() as
a failure and forgetting to set the error code is a common bug in this
situation.

The code is confusing but it's actually correct.  We are returning zero
deliberately.  Let's re-write it a bit to be more clear.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy and dsa random fixes/cleanups

These two patches were already present as part of my attempt to make
DSA modules work properly, these are the only two "valid" patches at
this point which should not need any further rework.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Factor the interrupt disabling in a function: bcm_sf2_intr_disable()
since we are doing the same thing in the setup and suspend paths.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fixed_phy_set_link_update() contains an early check against a NULL
callback pointer, which basically prevents us from removing any
previous callback we may have set. The users of the fp->link_update
callback deal with a NULL callback just fine, so we really want to allow
"removing" a link_update callback to avoid dangling callback pointers
during e.g: module removal.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kernel forcefully applies MTU values received in router
advertisements provided the new MTU is less than the current. This
behavior is undesirable when the user space is managing the MTU. Instead
a sysctl flag 'accept_ra_mtu' is introduced such that the user space
can control whether or not RA provided MTU updates should be applied. The
default behavior is unchanged; user space must explicitly set this flag
to 0 for RA MTUs to be ignored.
Signed-off-by: NHarout Hedeshian <harouth@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alexander Duyck says:

====================
Fixes and improvements for recent fib_trie updates

While performing testing and prepping the next round of patches I found a
few minor issues and improvements that could be made.

These changes should help to reduce the overall code size and improve the
performance slighlty as I noticed a 20ns or so improvement in my worst-case
testing which will likely only result in a 1ns difference with a standard
sized trie.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While doing further work on the fib_trie I noted a few items.

First I was using calls that were far more complicated than they needed to
be for determining when to push/pull the suffix length.  I have updated the
code to reflect the simplier logic.

The second issue is that I realised we weren't necessarily handling the
case of a leaf_info struct surviving a flush.  I have updated the logic so
that now we will call pull_suffix in the event of having a leaf info value
left in the leaf after flushing it.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function fib_find_alias is only accessed by functions in fib_trie.c as
such it makes sense to relocate it and cast it as static so that the
compiler can take advantage of optimizations it can do to it as a local
function.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It doesn't make much sense to count the pointers ourselves when
empty_children already has a count for the number of NULL pointers stored
in the tnode.  As such save ourselves the cycles and just use
empty_children.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch really does two things.

First it pulls the logic for determining if we should collapse one node out
of the tree and the actual code doing the collapse into a separate pair of
functions.  This helps to make the changes to these areas more readable.

Second it encodes the upper 32b of the empty_children value onto the
full_children value in the case of bits == KEYLENGTH.  By doing this we are
able to handle the case of a 32b node where empty_children would appear to
be 0 when it was actually 1ul << 32.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change corrects an issue where if inflate or halve fails we were
exiting the resize function without at least updating the slen for the
node.  To correct this I have moved the update of max_size into the while
loop so that it is only decremented on a successful call to either inflate
or halve.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses two issues.

The first issue is the fact that I believe I had the RCU freeing sequence
slightly out of order.  As a result we could get into an issue if a caller
went into a child of a child of the new node, then backtraced into the to be
freed parent, and then attempted to access a child of a child that may have
been consumed in a resize of one of the new nodes children.  To resolve this I
have moved the resize after we have freed the oldtnode.  The only side effect
of this is that we will now be calling resize on more nodes in the case of
inflate due to the fact that we don't have a good way to test to see if a
full_tnode on the new node was there before or after the allocation.  This
should have minimal impact however since the node should already be
correctly size so it is just the cost of calling should_inflate that we
will be taking on the node which is only a couple of cycles.

The second issue is the fact that inflate and halve were essentially doing
the same thing after the new node was added to the trie replacing the old
one.  As such it wasn't really necessary to keep the code in both functions
so I have split it out into two other functions, called replace and
update_children.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In doing performance testing and analysis of the changes I recently found
that by shifting the index I had created an unnecessary dependency.

I have updated the code so that we instead shift a mask by bits and then
just test against that as that should save us about 2 CPU cycles since we
can generate the mask while the key and pos are being processed.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4: Fix and enhance the device reset flow

This series from Yishai Hadas fixes the device reset flow and adds SRIOV support.

Reset flows are required whenever a device experiences errors, is unresponsive,
or is not in a deterministic state. In such cases, the driver is expected to
reset the HW and continue operation. When SRIOV is enabled, these requirements
apply both to PF and VF devices.

Currently, the mlx4 reset flow doesn't work properly: when a fatal error is
detected on the FW internal buffer the chip is not reset and stays in its
bad state. There are cases that assumed to be fatal such as non-responsive FW,
errors via closing commands but are not handled today.

The AER mechanism should also be fixed:
- It should use mlx4_load_one instead of __mlx4_init_one which is done
  upon HCA probing.
- It must be aligned with concurrent catas flow, mark device to be in
  an error state, reset chip, etc.
- Port types should be restored to their original values before error occurred.

In addition, there the SRIOV use-case isn't supported.

In above cases when the device state becomes fatal we must act as follows:
1) Reset the chip and mark the HW device state as in fatal error.
2) Wake up any pending commands, preventing new ones to come in.
3) Restart the software stack.

We also address the SRIOV mode as follows: In case the PF detects a fatal error,
it lets VFs know about that, then both itself and VFs are restarted asynchronously.
However, in case only the VF encountered a fatal case or forced to be reset, they
reset the VF stuff and then restart software.

changes from V0:

No need to call pci_disable_device upon permanent PCI error. This will
be done as part of mlx4_remove_one which is called later once we
return PCI_ERS_RESULT_DISCONNECT from the pci error handler.

Initial toggle value should use only the T bit and not the whole byte value.
Not doing so sometimes broke SRIOV as of junky value seen by the VF as a
non-ready comm channel
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When SRIOV commands are executed over the comm-channel and get
a fatal error (e.g. timeout, closing command failure) the VF enters
into error state and reset flow is activated.

To be able to recognize whether the failure was on a closing command, the
operational code for the given VHCR command is used. Once the device entered
into an error state we prevent redundant error messages from being printed.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In SRIOV, both the PF and the VF may attempt device recovery whenever they
assume that the device is not functioning.  When the PF driver resets the
device, the VF should detect this and attempt to reinitialize itself.

The VF must be able to reset itself under all circumstances, even
if the PF is not responsive.

The VF shall reset itself in the following cases:

1. Commands are not processed within reasonable time over the communication channel.
This is done considering device state and the correct return code based on
the command as was done in the native mode, done in the next patch.

2. The VF driver receives an internal error event reported by the PF on the
communication channel. This occurs when the PF driver resets the device or
when VF is out of sync with the PF.

Add 'VF reset' capability, which allows the VF to reinitialize itself even when the
PF is not responsive.

As PF and VF may run their reset flow simulantanisly, there are several cases
that are handled:
- Prevent freeing VF resources upon FLR, when PF is in its unloading stage.
- Prevent PF getting VF commands before it has finished initializing its resources.
- Upon VF startup, check that comm-channel is online before sending
  commands to the PF and getting timed-out.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix AER callbacks to work properly, it includes:
- Refractoring AER to be aligned with Reset flow support.
- Sync with concurrent catas flow.

In addition, fix the shutdown PCI callback to sync with
concurrent catas flow.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to manage interface state to sync between reset flow and some other
relative cases such as remove_one. This has to be done to prevent certain
races. For example in case software stack is down as a result of unload call,
the remove_one should skip the unload phase.

Implement the remove_one case, handling AER and other cases comes next.

The interface can be up/down, upon remove_one, the state will include an extra
bit indicating that the device is cleaned-up, forcing other tasks to finish
before the final cleanup.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We activate reset flow upon command fatal errors, when the device enters an
erroneous state, and must be reset.

The cases below are assumed to be fatal: FW command timed-out, an error from FW
on closing commands, pci is offline when posting/pending a command.

In those cases we place the device into an error state: chip is reset, pending
commands are awakened and completed immediately. Subsequent commands will
return immediately.

The return code in the above cases will depend on the command. Commands which
free and close resources will return success (because the chip was reset, so
callers may safely free their kernel resources). Other commands will return -EIO.

Since the device's state was marked as error, the catas poller will
detect this and restart the device's software stack (as is done when a FW
internal error is directly detected). The device state is protected by a
persistent mutex lives on its mlx4_dev, as such no need any more for the
hcr_mutex which is removed.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This includes:

- resetting the chip when a fatal error is detected (the current code
  does not do this).

- exposing the ability to enter error state from outside the catas code
  by calling its functionality. (E.g. FW Command timeout, AER error).

- managing a persistent device state. This is needed to sync between
  reset flow cases.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using a WQ per device instead of a single global WQ, this allows
independent reset handling per device even when SRIOV is used.

This comes as a pre-patch for supporting chip reset
for both native and SRIOV.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an HCA enters an internal error state, this is detected by the driver.
The driver then should reset the HCA and restart the software stack.

Keep ports information and some SRIOV configuration in a persistent area
to have it valid across reset.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Maintain a persistent memory that should survive reset flow/PCI error.
This comes as a preparation for coming series to support above flows.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call hex2bin() library function instead of doing conversion here.
Signed-off-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call hex2bin() library function, instead of doing conversion here.
Signed-off-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-01-22

This series contains updates to e1000, e1000e, igb, fm10k and virtio_net.

Asaf Vertz provides a fix for e1000 to future-proof the time comparisons
by using time_after_eq() instead of plain math.

Mathias Koehrer provides a fix for e1000e to add a check to e1000_xmit_frame()
to ensure a work queue will not be scheduled that has not been initialized.

Jacob adds the use of software timestamping via the virtio_net driver.

Alex Duyck cleans up page reuse code in igb and fm10k.  Cleans up the
page reuse code from getting into a state where all the workarounds
needed are in place as well as cleaning up oversights, such as using
__free_pages instead of put_page to drop a locally allocated page.

Richard Cochran provides 4 patches for igb dealing with time sync.
First provides a helper function since the code that handles the time
sync interrupt is repeated in three different places.  Then serializes
the access to the time sync interrupt since the registers may be
manipulated from different contexts.  Enables the use of i210 device
interrupt to generate an internal PPS event for adjusting the kernel
system time.  The i210 device offers a number of special PTP hardware
clock features on the Software Defined Pins (SDPs), so added support for
two of the possible functions (time stamping external events and
periodic output signals).

Or Gerlitz fixes fm10k from double setting of NETIF_F_SG since the
networking core does it for the driver during registration time.

Joe Stringer adds support for up to 104 bytes of inner+outer headers in
fm10k and adds an initial check to fail encapsulation offload if these
are too large.

Matthew increases the timeout for the data path reset based on feedback
from the hardware team, since 100us is too short of a time to wait for
the data path reset to complete.

Alexander Graf provides a fix for igb to indicate failure on VF reset
for an empty MAC address, to mirror the behavior of ixgbe.

Florian Westphal updates e1000 and e1000e to support txtd update delay
via xmit_more, this way we won't update the Tx tail descriptor if the
queue has not been stopped and we know at least one more skb will be
sent right away.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
vxlan: Don't use UDP socket for transmit

UDP socket is not pertinent to transmit for UDP tunnels, checksum
enablement can be done without a socket. This patch set eliminates
reference to a socket in udp_tunnel_xmit functions and in VXLAN
transmit.

Also, make GBP, RCO, can CSUM6_RX flags visible to receive socket
and only match these for shareable socket.

v2: Fix geneve to call udp_tunnel_xmit with good arguments.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the vxlan transmit path there is no need to reference the socket
for a tunnel which is needed for the receive side. We do, however,
need the vxlan_dev flags. This patch eliminate references
to the socket in the transmit path, and changes VXLAN_F_UNSHAREABLE
to be VXLAN_F_RCV_FLAGS. This mask is used to store the flags
applicable to receive (GBP, CSUM6_RX, and REMCSUM_RX) in the
vxlan_sock flags.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The UDP tunnel transmit functions udp_tunnel_xmit_skb and
udp_tunnel6_xmit_skb include a socket argument. The socket being
passed to the functions (from VXLAN) is a UDP created for receive
side. The only thing that the socket is used for in the transmit
functions is to get the setting for checksum (enabled or zero).
This patch removes the argument and and adds a nocheck argument
for checksum setting. This eliminates the unnecessary dependency
on a UDP socket for UDP tunnel transmit.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable kernel config "CONFIG_HAVE_DMA_API_DEBUG", FEC have kernel warning:
[    6.650444] fec 2188000.ethernet: DMA-API: device driver tries to free DMA memory it has not allocated
[    6.664289] Modules linked in:
[    6.667378] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 3.19.0-rc4-00688-g88340160-dirty #150
[    6.675841] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[    6.681698] Backtrace:
[    6.684189] [<80011e3c>] (dump_backtrace) from [<80011fdc>] (show_stack+0x18/0x1c)
[    6.691789]  r6:80890154 r5:00000000 r4:00000000 r3:00000000
[    6.697533] [<80011fc4>] (show_stack) from [<806d2d88>] (dump_stack+0x80/0x9c)
[    6.704799] [<806d2d08>] (dump_stack) from [<8002a4e4>] (warn_slowpath_common+0x7c/0xb4)
[    6.712917]  r5:00000445 r4:00000000
[    6.716544] [<8002a468>] (warn_slowpath_common) from [<8002a5c0>] (warn_slowpath_fmt+0x38/0x40)
[    6.725265]  r8:809a2ee8 r7:00000000 r6:00000000 r5:00000000 r4:00000042
[    6.732087] [<8002a58c>] (warn_slowpath_fmt) from [<802d6268>] (check_unmap+0x86c/0x98c)
[    6.740202]  r3:808c79bc r2:8089060c
[    6.743826] [<802d59fc>] (check_unmap) from [<802d65e4>] (debug_dma_unmap_page+0x80/0x88)
[    6.752029]  r10:00000000 r9:00000000 r8:00000000 r7:00000001 r6:be12a410 r5:00000000
[    6.759967]  r4:00000042
[    6.762538] [<802d6564>] (debug_dma_unmap_page) from [<80440248>] (fec_enet_rx_napi+0x7ec/0xb9c)
[    6.771345]  r7:00000400 r6:be3e4000 r5:bf08fa20 r4:be036000
[    6.777094] [<8043fa5c>] (fec_enet_rx_napi) from [<8056ae24>] (net_rx_action+0x134/0x324)
[    6.785297]  r10:be089e60 r9:80998180 r8:ffff8d68 r7:0000012c r6:00000040 r5:00000001
[    6.793239]  r4:be036718
[    6.795801] [<8056acf0>] (net_rx_action) from [<8002db24>] (__do_softirq+0x138/0x2d0)
[    6.803655]  r10:00000003 r9:00000003 r8:80996378 r7:8099c080 r6:00000100 r5:8099c08c
[    6.811593]  r4:00000000
[    6.814157] [<8002d9ec>] (__do_softirq) from [<8002dd00>] (run_ksoftirqd+0x44/0x5c)
[    6.821836]  r10:00000000 r9:00000000 r8:809b133c r7:00000000 r6:00000001 r5:00000000
[    6.829775]  r4:be027e80
[    6.832346] [<8002dcbc>] (run_ksoftirqd) from [<80048290>] (smpboot_thread_fn+0x154/0x1c4)
[    6.840649] [<8004813c>] (smpboot_thread_fn) from [<80044780>] (kthread+0xdc/0xf8)
[    6.848224]  r10:00000000 r8:00000000 r7:8004813c r6:be027e80 r5:be027ec0 r4:00000000
[    6.856179] [<800446a4>] (kthread) from [<8000ebc8>] (ret_from_fork+0x14/0x2c)
[    6.863425]  r7:00000000 r6:00000000 r5:800446a4 r4:be027ec0
[    6.869156] ---[ end trace 861cf914d2461a8b ]---

There have one bug in .fec_enet_tx_queue() function to unmap the DMA memory:
For SG or TSO, get one buffer descriptor and then unmap the related DMA memory, and then
get the next buffer descriptor, loop to while() to check "TX_READY". If "TX_READY" bit
still __IS__ existed in the BD (The next fraglist or next TSO packet is not transmited
complitely), exit the current clean work. When the next work is triggered, it still repeat
above step with the same BD. The potential issue is that unmap the same DMA memory for
multiple times.

The patch fix the clean work for SG and TSO packet.
Reported-by: NAnand Moon <moon.linux@yahoo.com>
Reported-by: NChristian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sathya Perla says:

====================
be2net: patch set

Hi David, as the below patch-set includes minor bug fixes and some
code re-org, pls consider applying it to the "net-next" tree. Thanks!

Patch 1 fixes a bit of code duplication involving interface object
creation code.

Patch 2 ensures that when a flow-control FW cmd fails, the adapter state
continues to reflect the old values. This allows for correct reporting
on subsequent ethtool "get".

Patch 3 returns proper error for link config change on BE3/Lancer

Patch 4 adds a kernel log message for FW boot error on Lancer

Patch 5 adds a function reset on Lancer as a part of the function init
sequence.

Patch 6 moves some FW-cmd definitions that belong in be_cmds.h, but
were placed in be_hw.h

Patch 7 resets the "bw_min" field while configuring "bw_max" needed
for TX rate limiting config.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When max_tx_rate is set via bw_max in the NIC resource desc, bw_min must be
set to 0.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some FW cmd related definitions were included in be_hw.h
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Lancer FW is picky about requiring a function reset FW cmd as a part
of the initialization sequence.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a log message in case of POST timeout in Lancer to
help debugging failure cases. It also logs sliport_status register value in
case of POST timeout.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The support for this exists only in skyhawk FW.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the FW cmd to set flow control fails, the adapter state must simply
reflect the old values.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This removes a bit of duplication of code that initializes the en_flags.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Romain Perier says:

====================
net: stmmac: dwmac-rk: Fix phy regulator issues

This series fixes few issues in dwmac-rk:

1. Voltage settings was hardcoded into the driver for the phy regulator.
   The driver now uses the default voltage settings found in the devicetree,
   which are applied throught the regulator framework.
2. The regulator name used to power on or power off the phy was put in the devicetree
   variable "phy_regulator", which is not standard and added a lot of code for nothing.
   The driver now uses the devicetree property "phy-supply" and the corresponding functions
   to manipulate this regulator.

The corresponding devicetree files are also updated. As this new binding for
rk3288 has not been released with any official kernel yet (not until 3.20),
I don't need to care about keeping compatibility with the old non standard property.
====================
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>